Kogan KASBRBT21A User manual

2.1 Wireless Soundbar
with Bluetooth
KASBRBT21A
Quick Start Guide
Product Speci ications
Power Supply AC 100-240V / 50-60Hz
Total Power Consumption 80W
Input Sensitivity (Subwoo er) 300mV -/+ 20mV
Input Sensitivity (Satellite) 800mV -/+ 50mV
Speaker impedance o Satellite 4 Ohm
S/N (A Weight) 8 Ohm
THD (1kHz, 1W) 0.5%
Frequency Response 45Hz ~ 20KhzdB
L/R Separation (1kHz) 30dB
L/R Balance (Stereo) +/- 2dB
Bluetooth Transmission Distance CSR 2.1m
2.4G Between wireless subwoo er transmission distance 5 met es
Controls and Functions
Front Panel
Rear Panel

Sa ety Precautions
All safety and ope ational inst uctions should be ead befo e the unit is used.
A copy of these inst uctions should be kept fo futu e efe ence.
•Powe & Powe Co d: connect the device to the powe type as advised. Do not place
objects on top of the powe co d.
•Wate & Moistu e: the device should not be used nea wate (fo example, nea a
bathtub, sink, laund y, nea a swimming pool etc..)
•Ventilation: The device should be situated so that its location o position does not
inte fe e with its p ope ventilation. Do not use the device on a bed, sofa, ug o simila
su face that may block the ventilation openings.
•Heat: Keep the device away f om heat sou ces such as adiato s, heate s, stoves o othe
appliances that gene ate heat.
•Damage equi ing se vice: The appliance should be se viced by the Kogan custome
suppo t technicians when:
1) The powe -supply co d o the plug has been damaged; o
2) Objects o liquids have fallen into the device; o
3) The device has been exposed to ain; o
4) The device is not ope ating no mally o exhibits a ma ked change in pe fo mance; o
5) The device has been d opped o damaged.
•Clean only with a d y cloth.
•Unplug the device du ing lightning sto ms o when it will emain unused fo extended
pe iods of time.
Remote Control
1 Standby (On/Off)
2 No mal Mode
3 Reset (location et ieval button)
4 Bluetooth t ack P ev
5 Volume down
6 Bass down
7 Music mode
8 Input
9 Bluetooth t ack next
10 Mute mode
11 Movie mode
12 EQ adjust sound effect
13 Sho t p ess: Bluetooth Play/Pause
Long p ess: Blueooth Pai /Disconnect
14 Volume op
15 Bass up
Remote control battery replacement
1. Replace the emote cont ol batte y when the ange is
educed conside ably.
2. Use only C 2025 o D12032 3V lithium batte ies.
3. Bea in mind that lighting and othe oom conditions, in
addition to batte y age, can affect the ope ating ange
of an inf a ed emote cont ol.

System Connection Instructions
Basic Status
Connected AUX single, Optical and Coaxial signal on the ea panel of the Sound Ba .
The LED display will display “- -” to show it is in standby mode.
LED Digit Status and Function
LED DIGIT FUNCTION LED DIGIT FUNCTION
AU AUX audio signal input EQ Adjust Equalise mode
OP Optical audio signal input E1 No mal sound effect
CO Coaxial signal input E2 Music sound effect
BL Bluetooth audio signal input E3 Movie sound effect
Numbe Volume label
EQ Setting
T eble setting: p ess the EQ button on the emote cont ol, then p ess the VOL+ button and the
VOL- button to adjust the t eble, with the ange inc easing o dec easing by 7db. (Reset: P ess
EQ, then p ess the eset button).

Pairing the Soundbar & Subwoo er
To use the wi eless subwoofe , you must ensu e that the soundba itself has
been powe ed up and is eady fo pai ing. To do this, simply tu n the soundba
on, then switch the subwoofe on 30 seconds late .
If you tu n the subwoofe on befo e the soundba has booted up, the units will
not pai and you will not get any sound f om the subwoofe . The failu e to pai
will be indicated by the small blue LED light in the ea of the subwoofe
flashing.
If the units fail to pai co ectly, tu n the subwoofe off, wait fo 10 seconds, then
switch it back on again.