Kohler Englefield Valencia 1500 FS User manual

1365837-A02-C 27/02/2019
INSTALLATION
INSTRUCTIONS
BATHS
Engleeld
FREESTANDING
Englefield has a history of
making superb baths and
their popularity is testament to
their quality and affordability.
It’s the details that Englefield
cares about - from pioneering
the latest technology, to
innovative design, it’s all to
make your bathing
experience the very best it
can be.
Valencia 1500 FS Bath
Valencia 1700 FS Bath
Part number: 24247A-0
Part number: 24248A-0
Sierra 1500 FS Bath
Sierra 1700 FS Bath
Part number: 24249A-0
Part number: 24250A-0
Product & Part Number
ROUGH IN DIMENSIONS
Rough-in dimensions
NOTE: Check the rough-in and room dimensions to provide adequate available
space for the bath unit. Check the flooring under designated bath position and make
repairs as needed. For best results, ensure that the floor is level.
585mm
585mm
750mm
750 /
800 mm
1500 / 1700mm
1500 / 1700mm
Tuscano 1500 FS Bath
Part number: 24251A-0
Tuscano 1700 FS Bath
Part number: 24252A-0
1500 / 1700mm
585
mm
750 / 800
mm
Studio II 1700 FS Bath
Part number: 24246A-0
1700mm
800mm
585
mm

Page 1
Before installing the bath please read these instructions carefully to familiarise yourself with
the required tools, materials and installation sequences. This will help you avoid costly
mistakes. The installation documents included assume that walls are plumb and floors are
level. Slight adjustments to the installation procedure may be required for out-of-square
surfaces.
In addition to proper installation, read all operating and safety instructions and refer to the
Homeowner’s Guide for important care and cleaning information. Ensure that all local
building and plumbing codes are observed.
These instructions contain important care, cleaning and warranty information. Please leave
these instructions for the consumer after installation.
INSTALLATION INSTRUCTIONSFREESTANDING BATHS
BEFORE YOU BEGIN
TOOLS AND MATERIALS REQUIRED
ENGLEFIELD
INSTALLATION
Note: Instructions, drawings, and diagrams contained in this manual present information available at the
time of printing. Although every attempt has been made to keep them up-to-date, Englefield reserves the
right to implement product changes without further notice.
1) Unpack the bath and check for any transit damage prior to installation.
2) Position the bath in the desired location in the bathroom.
3) Check that the plumbing can be connected to the bath when in the desired location and
that the positioning of the bath does not interfere with other bathroom fixtures.
Timber blocks
4) Install the waste system (not supplied) in accordance with the manufacturers instructions.
Please adhere to the relevant sections of NZS 3500 plumbing standard.

Page 2
INSTALLATION INSTRUCTIONSFREESTANDING BATHS
ENGLEFIELD
5) Raise the Free Standing bath off the floor by propping it up onto timber blocks
positioned at either end of the bath. Install and connect the waste outlet.
7) Carefully remove the timber blocks and use a spirit level to check that the bath is level
with the floor, adjust feet as necessary.
Product Part Number
40mm pop-up bath waste
99329A-CP
6) Adjust the feet so that the bottom of each foot is protruding approximately 3 to 5mm from
the underside of the bath. The feet must extend past the bath shell to take the weight
of the bath. Feet should be level with each other so that the weight of the bath is evenly
supported by the four feet.
Self-sealing trap with flexible waste pipe 80144A-NA
Recommended products are:
8) Carefully tilt the bath backward and apply an appropriate adhesive to each of the bath
feet. Lower the bath back into position.

Page 3
INSTALLATION INSTRUCTIONSFREESTANDING BATHS
ENGLEFIELD
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
Please refer to the Homeowner’s Guide for cleaning instructions.
For warranty information, please visit our website.
CLEANING AND MAINTENANCE INSTRUCTIONS
Installation complete.
Valencia Freestanding BTW Baths Sierra Freestanding BTW Baths
Ensure that the silicone sealant is
applied along the back edge of the bath.
Ensure that silicone sealant is applied
along the back edge and top edge of
sides of bath that are adjacent to a wall.
9) Apply silicone sealant between edges and adjacent surfaces ensuring that a watertight
seal is formed.
Tuscano Freestanding Baths
Ensure that silicone sealant is applied
along the base edges that are adjacent
to the floor.
Studio II Freestanding Baths
Ensure that silicone sealant is applied
along the base edges that are adjacent
to the floor.