Kohler ENGLEFIELD TRADE SERIES User manual

-1-
1310239-A02-A 10/01/2017
Sika Sikasil NG (Arctic White)
•To seal the WHITE shower door to the shower tray.
Usage:
• 1 cartridge per shower
Sika Sikasil NG (Translucent)
•To seal the METALLIC shower door to the shower tray.
Usage:
• 1 cartridge per shower
SEALANT REQUIRED TO COMPLETE THIS INSTALLATION:
IMPORTANT
READ ALL INSTRUCTIONS
CAREFULLY BEFORE
STARTING THE
INSTALLATION
THIS WILL ENSURE YOU
OBTAIN THE BEST
POSSIBLE
RESULTS
TOOLS REQUIRED
• Level
•Tape
•Pencil
•Phillips screwdriver
•Ruler
•Drill
•Caulking gun
INSTALLATION GUIDE
TRADE SERIES
ALCOVE SHOWER

Fitting Instructions – ALCOVE DOOR
INSTALLATION
INSTRUCTIONS
SHOWER WALL
DOOR RETAINER
INSTALLATION KIT
HANDLE KIT
DOOR SILL
TOP RAIL
DOOR
ASSEMBLY
SHOWER TRAY
DOOR
RETAINER
NOTE: SHOWER TRAY MUST BE INSTALLED AS
DETAILED ON SUPPLIED INSTRUCTIONS
1310239-A02-A 10/01/2017 -2-

Check the distance between the
walls to ensure they are within
the maximum and minimum
enclosure adjustment tolerances.
1dellatsniebTSUMesabrewohS
level.
3
It is recommended that the waste
outlet be ‘taped over’ to avoid the loss
of any components during installation.
2
Lift door panel onto the tray and slide
it hinge side into the wall retainer.
Push it hard against the wall.
6
CAUTION: BEFORE DRILLING
HOLES, ENSURE THERE ARE NO
ELECTRICAL CABLES OR WATER
PIPES BEHIND WALLS
Fix hinge side wall retainer in
place using 3 of the 6 long
screws. Make sure the screws go
into studs.
5
wall retainers by screwing
through the backing board
and into studs. Other
methods may cause warping
andmight void warranty.
Note: If screwing into backing
board only, use appropriate
wall anchors in the wall.
10 mm
Select preferred shower door
opening. It is recommended to start
the installation from the hinge side
of the door.
4
against shower wall, resting on the shower
the inside of the shower.
from the front of the shower base. Check
holes.
ENSURE WALL RETAINER PROFILE IS PLUMB.
TYPE ADJUSTMENT TOLERANCE (mm)
MIN MAX
900 mm
1000 mm
837
937
880
980
1310239-A02-A 10/01/2017 -3-

Attach second Wall Retainer
P
7Check that the Door Assembly
top edges are level.
10
Fit top and bottom hinge caps.
(Note: bottom cap has ‘wings’.)
11
position against the wall.
8
Centralise Door Assembly
9
Slide drip edge seal over wing
on bottom hinge cover and
Repeat between hinge cover
and door magnet extrusion.
12
door edge extrusion enough to slip
drip seal moulding underneath.
(Note: Drip seal moulding and
retainer and ‘handed’).
glass and pull into contact with
door edge extrusion. Clamp in
place using the bracket and No. 6
screw.
13
NOTE: DOOR ASSEMBLY MUST BE
PLUMB USING A SPIRIT LEVEL.
Fit the other small screw to the top
hole in the door edge extrusion.
front of the shower base.
Check vertical with spirit level and
remaining long scews. Ensure the
screws go into the stud.
Fit all 6 screw caps.
10 mm
1310239-A02-A 10/01/2017 -4-
trim seal
ush with
door glass

Using spirit level plumb
Door Assembly. Tape into
position as indicated.
14 Fit long seal to hinge edge of
glass. Flap faces into
enclosure. Push down to butt against
bottom seal. Trim to top of glass.
16
If door alignment is incorrect, door
will not function properly and
further adjustments are necessary.
Remove tape and re-align until
correct alignment is achieved.
DO NOT PROCEED TO STEP 15 UNTIL
DOOR IS OPERATING CORRECTLY.
NOTE: This is an important part of
the installation procedure and your
careful attention at this stage will
ensure that you will obtain the best
possible results.
IMPORTANT
TEST THE OPENING AND CLOSING
OPERATION OF THE PIVOT DOOR. SILICONE APPLICATION
18
(b) Hold tube at 45° angle and push
(c) The surface of the sealant can
be smoothed (before surface dries)
small quantity of water with one drop
of washing-up liquid added.
(d) Excess silicone should be
removed immediately with a damp
cloth.
(e) Allow the silicone 24 hours to
cure before using the enclosure.
CAUTION: Avoid contact with skin,
eyes and mouth and avoid breating
with water. If irritation persists, seek
medical attention. Keep out of reach
of children.
IMPORTANT
SILICONE SEALANT SHOULD BE
APPLIED TO ALL OUTSIDE JOINTS.
DO NOT SEAL FROM INSIDE.
Seal these areas:
A - Full height between retainers
and walls.
B - Between door sill and tray.
C - Between retainer and door
jamb to a height of 100mm.
(a) Cut tip of Silicone Tube Nozzle
at 45° angle.
Ensure all joints are clean and
dry before applying sealant.
For sealant application, follow
steps (a) to (e) below.
clear silicone is required.
silicone is required.
IMPORTANT
Fit handles following instruc-
tions supplied with handle.
17
Drill holes (use 2.5mm drill bit,
DO NOT USE A BIGGER DRILL
BIT) through punched holes at top
and bottom of each wall retainer to
secure door. Fix screws as pictured.
Fit caps & remove positioning tape.
15
1310239-A02-A 10/01/2017 -5-
See next page for a more detailed
explanation of sealant application.

1310239-A02-A 10/01/2017 -6-
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
For spare parts and warranty information, please visit our website.
SEALANT APPLICATION STEPS
SEALANT APPLICATION
Ensure all joints are clean and
dry before applying sealant.
(b) Hold the tube at 45° angle & push
(c) The surface of the sealant can
be smoothed (before surface dries)
a small quantity of water with one
drop of washing liquid added.
(d) Excess sealant should be
removed immediately with a
damp cloth.
IMPORTANT
SIKASIL NG SEALANT SHOULD BE
APPLIED TO ALL OUTSIDE JOINTS.
DO NOT SEAL FROM INSIDE.
CAUTION
AVOID CONTACT WITH SKIN, EYES &
MOUTH. AVOID BREATHING VAPOUR.
IF IN EYES, IMMEDIATELY FLUSH WITH
WATER. IF IRRITATION PERSISTS, SEEK
MEDICAL ATTENTION.
KEEP OUT OF REACH OF CHILDREN
2a. Seal full height of the joint
between the Walls and the
Wall Retainers.
(a) Cut tip of silicone tube nozzle
at 45° angle.
1.
(e) Allow the silicone 24 hours to
cure before using the enclosure.
6mm
45°
For sealant application, follow
steps (a) to (e) detailed below.
b. Seal joint between the Door
Sill and the shower tray.
To a height of 100mm, seal
joints between Door Frame
& Wall Retainer.
c.
IMPORTANT
ALLOW 24 HOURS FOR SEALANT AND
ADHESIVE TO CURE BEFORE USING THE
SHOWER.
24hrs