Kohler 10089W-CP User manual

11081774-W2-A
IMPORTANT
INSTALLER: THIS MANUAL IS THE PROPERTY OF THE
CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT
FOR MAINTENANCE AND OPERATIONAL PURPOSES.
Installation and User Guide
Oblo Deck and Wall Mounted Bath/Shower
Mixers and Wall Mounted Thermostatic
Shower
MODEL NUMBERS
Important! Please quote the above model number(s) when ordering spares
10089W-CP, 10091W-CP, 10098W-CP

2
1081774-W2-A
CONTENTS
Specication ............................................................................................2
Pressures ............................................................................................. 2
Temperatures .......................................................................................2
Installation ...............................................................................................3
Before you Begin..................................................................................3
Install the Wall Mounted Mixer .............................................................3
Install the Deck Mounted Mixer............................................................ 4
Connect the Shower Fittings ................................................................5
Finish the Installation............................................................................5
Operation.............................................................................................. 5
User Maintenance....................................................................................6
Cleaning ............................................................................................... 6
Spare Parts ..............................................................................................6
Dimensions ..............................................................................................7
Customer Care.........................................................................................8
SPECIFICATION
Pressures
The minimum recommended operating pressure is 0.5 bar.
For optimum performance, a minimum operating pressure of 1.0 bar is
recommended.
Temperatures
Minimum hot water supply temperature: 50°C
Maximum hot water supply temperature:70°C
Recommended hot water supply temperature: 60°C
Temperature adjustment range (approximate): 20°C - 50°C
Safety button set at: 38°C
Maximum hot water temperature from mixer: 50°C

31081774-W2-A
Install the Wall Mounted Mixer
1. Install the bath and drain (refer to the manufacturer’s instructions).
Note! When wall mounting the mixer it should be noted that the product is supported
by the pipework only.
2. Make sure that the connectors are level and set at the correct distance apart.
Note! Make sure that the connectors extend 40 - 45 mm from the nished wall.
3. Screw on the concealing plates hand tight.
4. Position the washer on each of the nuts.
5. Align the mixer and connectors and tighten the nuts using the special tool
supplied.
Note! Make sure that you do not damage the chrome plated surfaces when
you tighten the nuts.
INSTALLATION
Before you Begin
1. Make sure that the tap is installed by a competent installer.
2. Turn off the water supply.
3. The plumbing installation must comply with Building Regulations or any
particular regulations and practices, specied by the local water company or
water undertakers.
150 mm
Spirit Level
40-45 mm
1
2
3

4
1081774-W2-A
Install the Deck Mounted Mixer
1. Install the two column connectors to the mixer.
2. Install the grub screw and tighten with a hexagonal wrench.
3. Place the concealing plate over the threaded section of the column
connectors.
4. Apply a ring of sealant in accordance with the manufacturer’s instructions
underneath the concealing plates.
5. Fit the mixer through the top of the bath.
6. Install the washers and the locknuts. Use a tap spanner to tighten the nut.
7. Remove any excess sealant.
1
2
Concealing Plate
Locknut
Washer
Apply Sealant

51081774-W2-A
Connect the Shower Fittings
1. Install the shower ttings (refer to the manufacturer’s instructions).
2. Connect the shower ttings to the mixer.
Finish the Installation
1. Make sure that the mixer knobs are in the off position.
2. Turn on the hot and cold water supplies and check for leaks from both the mixer
and the drain.
3. Use the special key (provided) to unscrew and remove the aerator.
4. Turn on the hot and cold knobs and allow the water to run for approximatley
one minute to remove any debris.
5. Turn the hot and cold knobs to the off position and re-install the aerator using
the special key.
Operation
Set the temperature by slowly turning the temperature selector (right handle).
For safety reasons there is a stop that limits the tempeature to 38°C. To get a higher
temperature, push the button and contiue turning the temperature selector
Tool
Aerator
Shower