Kohler 73087T-B4 User manual

1338435-2A-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. The minimum working pressure for the diverter is 0.05MPa(0.5bar).
5. Check for leaks before covering the pipes, repairs as needed.
6. The highest working pressure for handshower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure
reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower and
shower arm away from heater, or it may become damaged and cause injury to the user.
7. Please purchase the matched mounting base 97905T when install the faucet.
INSTALLATION INSTRUCTIONS
73087T-B4 Floor Mount Bath Filler With Handshower
ROUGH-IN DIMENSIONS
*Please purchase the appropriate bathtub according to the dimension.
1338435-2A-A 4
SERVICE PARTS
COMPOSED
73087T-B4 Floor Mount Bath Filler With Handshower
COMPOSED
G1/2˝
G1/2˝
1500
Hose
658~678
901~921
G1/2˝ 2º
*210
50 233
*70 Min.
816~836
883~903
630 Max.
Ø124
Bathtub
50
94
Handshower
Ø28
240
250
G1/2˝
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
Special model meets or exceeds the following at date of manufacture: TIS
STANDARD APPLICABLE
880010
2BZ:1202014-2BL
Others:831727**
880010
1082901
1084120
833730
835598
77955
1010167
3023925**
831752
1229992
3023748 3022132**
3023796**
1249005
3006148
1258088
1297467**
3023611 3023609** 3023751
3022141**
834638
834404
1030624
1240266
77420

1338435-2A-A 2 1338435-2A-A 3
INSTALLATION CHECKOUT
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
INSTALLATION
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off
position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Remove the aerator(15) by key(14).
Remove the handshower(11). Turn on
faucet handle. Run hot and cold water
through spout for about one minute to
remove any debris. Check for leaks at
this time. Remove any debris. Shut off
the faucet. Reinstall the aerator and
handshower.
How to Install the Handshower
Remove the protector from diverter
kit(9).
If needed, install the restrictor(13) into
the inlet of the handshower(11).
Connect hose(10) to diverter kit and
handshower with washers. Tighten all
the connections.
Hang the handshower on the bracket
(12) of the faucet.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
Press the diverter for handshower. Pull the diverter in the normal position for bath spout.
5
4
7
8
1
6
2
3
How to Install the Faucet
Shut off water supply. Cut away the
extending part of the base protector(1)
in accordance with the tile surface.
Remove plug(2) from the base.
Remove protector(3) from the faucet.
Slide up the escutcheon kit(4). Install
the faucet. NOTE: Keep the faucet
vertical to base, to avoid damaging the
O-rings on the bottom.
Keep the spout pointing to tub. Fix the
faucet to the base with screws(5) and
washers(6) through flange(7). Tighten
the screws with hex wrench(8).
Slide down the escutcheon kit, make
sure it against the finished wall.
11
13
9
12
10
15
14
11
Katalyst Air
Intense Massage
How to Operate the Handshower
Press the buttons of the handshower to
change the water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause
the flow stream to become distorted or
reduce the flow rate. To remove the debris
or mineral build-up, run water through the
handshower, firmly press or rub your finger
back and forth across the rubber nozzles.
Remove and clean the screen washer.