Kohler Candide 7688K-4E3 User manual

All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
3. The highest working pressure for handspray is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure
reducer is needed. The highest water and environment temperature is 60°C. Please keep handspray,
showerhead and the shower arm away from heater, or it may become damaged and cause injury to the user.
1141292-2A-B 1
7688K-4E3 WALL MOUNT BATH & SHOWER FAUCET
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
Wall Mount Bath & Shower Faucet
ROUGH-IN DIMENSIONS
Lift the handle gently. Turn clockwise for hot water, turn counter-clockwise for cold water.
Diverter turns clockwise for shower. Shut off the faucet, turns counter-clockwise until it stops for bath spout.
HANDLE OPERATION
115
Ø60
Ø66
G1/2˝
159
G1/2˝
24°
170
150±15
226
G1/2 ˝
Ø90
88
G1/2˝
G1/2˝
1500
**Color code must be specified when ordering
SERVICE PARTS
1141292-2A-B 4
7688K-4E3 WALL MOUNT BATH & SHOWER FAUCET
Wall Mount Bath & Shower Faucet
1169649
Restrictor
1181006**
Handspray
831727**
Hose
3010479**
Lever
833438
Screw
834705
Plug
3006660
Nut
834460
Valve
880084
O-Ring
880085
O-Ring
3008415**
Diverter Plug
834562**
Aerator
1216770**
Shower Bracket
3008440**
Diverter Assy
831752
Check Valve
1219595**
Connection Kit
880010
Washer
49
40º
27
60
58

1141292-2A-B 2
CLEANING INSTRUCTIONS
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight.
Ensure that the lever handle is in the close position.
Turn on the main water supply, and check for leaks. Repair as
needed.
Remove the aerator assembly(15) and handspray. Run hot and cold
water through the faucet for about one minute to remove any debris.
Check for leaks. Remove any debris from the aerator assembly. Shut
the faucet off, and reinstall the aerator assembly and handspray.
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a clean
soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. Which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
1141292-2A-B 3
45
7
6
How to Install the Faucet
To perform installation, installer must provide G1/2˝ female supply
fittings(1), spaced 150mm apart, horizontal and not extending beyond
finished wall surface. Hot supply pipe must be located on the left.
Flush the water supply pipes thoroughly to remove any debris.
Install the two offset connectors(2) into the hot and cold supply pipes.
Use appropriate thread sealants on pipe threads.
Adjust the center-to-center distance between the connectors to
150mm and horizontal. They should extend 29mm beyond the
finished wall.
Thread the escutcheons(3) onto the connectors until they are against
the finished wall.
Insert washer seals(4) into supply nuts(5) of the faucet. Thread the
faucet supply nuts onto the connectors and tighten. When tighten the
nuts, use strap wrench or soft cloth between product and regular
wrench to protect the finish.
Insert the water flow restrictor(9) into the inlet of the handspray(10) if
needed. Connect hose(8) to the faucet outlet(7), and to the handspray
with washers(6).
INSTALLATION
29mm
150mm
2
1
Hot
Cold
8
10
3
9
6
How to Install the Shower Bracket
Determine a suitable location on the finished wall to install the bracket.
Mark bracket base mounting hole locations on the wall according to the
dimension. Drill two holes on the finished wall, the holes should match
the anchors(11). Install the anchors.
Tighten screws(12) to secure bracket base(13, flat side upward). Put
the bracket(14) onto the bracket base and lock by stopper.
15
27
12
14
13
11