Kohler LOURE 97907T-4 User manual

1262282-2A-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. If possible, install this faucet before installing the lavatory.
3. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
4. Observe local plumbing codes.
5. Shut off the water supplies to the fitting.
6. The hightest working pressure for faucet is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure
reducer is needed. Or maybe damage the faucet.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, turn counter-colckwise for cold water.
1262282-2A-A 4
INSTALLATION INSTRUCTIONS
97907T-4 Single Handle Lavatory Faucet
97908T-4 Single Handle Tall Lavatory Faucet
LOURE
97907T-4 Single Handle Lavatory Faucet
97908T-4 Single Handle Tall Lavatory Faucet
LOURE
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering.
97908T-4
97907T-4
188~200
Ø69
Ø60
Ø41.2
27~60
Ø31.75
112
188~200
Ø69
Ø60
Ø41.2
27~60
Ø31.75
112
219
113
525
50 Max.
375370
50 Max.
G1/2˝
G1/2˝
Ø31~Ø37
Ø31~Ø37
135
135
36º
36º
269
1245336**
832751
1262286
1262287
1245330**
1245332
1267494**
1123942
1115707
1115726
1113689
1115710
1245337**
1249321
1267495
880096
1228834
50729
871472
1245333
834704
1182548
1069314
1069314
97907T-4:1245335
97908T-4:1249319
1142103**
1102890**
1102891
1102892

1262282-2A-A 2 1262282-2A-A 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Spout
If needed to take off the hoses(4) to repair, reinstall
and tighten them by hand.
Install the mounting stud(2) into the faucet body
base(1). Slide the washer(3) over the flexible hoses(4)
and mounting stud, and into the groove at the bottom
of the faucet body.
Insert the faucet assembly into the lavatory hole.
Position the faucet. From underside of the lavatory,
place the brackets(5, Rubber washer is on the top)
onto the mounting stud. Tighten the nuts(6) by
wrench(7) to secure the faucet.
Attach the hoses to water supplies. The hose with
"COLD" label connects to cold water.
7
1
2
3
4
6
5
12
13
11
10
9
8
How to Install the Drain
Remove the locknut(8), plastic washer(9), rubber
gasket(10) from the drain body(11).
Insert the drain body into the lavatory. Reinstall the
rubber gasket(Tapered side up), plastic washer and
locknut back to the drain body in turn. Tighten the
locknut.
NOTE: If needed, apply a ring of plumbers putty or
other sealants around the underside of the drain
flange(12), instead of using rubber washer(13).
Do not reposition the drain after the locknut is
tightened, or you may break the putty or sealant seal.
Remove any excess putty.
17
18
16
19
20
14
15
Ensure that all connections are tightened and the
handle is in the off position.
Open the drain. Turn on main water supply and check
for leaks. Repair as required.
Loosen screw(15) with 1.5mm hex wrench(14).
Remove the aerator(17) carefully with key(16). Turn
on the faucet. Run the water through the spout for
about one minute to remove any debris. Remove any
debris from the aerator. Shut off the faucet. Keep the
fixing hole facing downwards, reinstall the aerator.
Replacing the Washer & Piston Kit
Turn counterclockwise to remove the stopper(18).
Take out washer(19). Replace with a new one.
Turn counterclockwise to remove the piston kit(20).
Replace with a new one. Reinstall stopper and
washer.
①
②