Kohler MAXISPACE 2.0 K-24369X User manual

Kohler Co. 1 1358590-X2-A
BEFORE YOU BEGIN 
TOOLS 
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect
it for damage. Return the lavatory to its protective carton
until you are ready to install it.
The walls and floor must be square, plumb, and level.
All information in these instructions is based upon
the latest product information available at the time of
publication. Kohler Co. reserves the right to make
changes in product characteristics, packaging, or
availability at anytime without notice.

 





INSTALLATION AND CARE GUIDE
ขอแนะนําการติดตั้งและการดูแลรักษา
MAXISPACE 2.0 VANITY LAVATORY


K-24369X / K-24370X

1358590-X2-A 2 Kohler Co.
ROUGH-IN 
Dimensions are approximate.
Unit: mm


*Kohler reserves the right to change marked dimensions without prior notice.

K-24369X-1
35
75
380
154
450 202
80
145
447
70
800
K-24370X-1
522
196
75
1000
450 204
145
70
80
447
35
Fig. 1 / 

Kohler Co. 3 1358590-X2-A
INSTALLATION 
Install the Lavatory
NOTE: The lavatory tops must be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
Rough-in the supplies and the drain piping.
NOTE: The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
Drill two 10 mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 65-75 mm
of each bolt remains exposed.
NOTE:
1. The distance from center of vanity drain hole to the wall is 80
mm (see roughing-in), and please choose suitable drainage
pipe.
2. The height in Fig. 2 to Fig. 3 can be adjusted according to
actual height of the cabinet. Inlet of hot water and cold water
can be adjusted according to installation conditions.
3. Other fastening devices of sufcient size and strength may
also be used.

 











1.





K-24369X-1
MAXISPACE 2.0 800mm Vanity Top

Finished floor / 
 1-1/2” OD / 
G1/2” COLD / 
Center of vanity

Attachment
Bolt (x2)

G1/2” HOT
Wall Plug

Fig. 2 / 

1358590-X2-A 4 Kohler Co.
Install the faucet and drain to the lavatory according to the
manufacture's instructions.
Put the sealant around the back wall attached surface of
the lavatory evenly.
Carefully place the lavatory against the wall, so the hanger
bolts extend through the lavatory holes.




Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
CAUTION: Risk of product damage. Do not overtight-
en the cap nuts. Overtightening may cause damage to
the product.
Clean the lavatory top.





Apply Silicone sealant along this face.

Washer

Nut

Offset Nut

Fig. 4 / 
Finished floor / 
 1-1/2” OD / 
G1/2” COLD / 
Center of vanity

Attachment
Bolt (x2)

G1/2” HOT
Wall Plug

K-24370X-1
MAXISPACE 2.0 1000mm Vanity Top

Fig. 3 / 

Kohler Co. 5 1358590-X2-A
Take out Deck and place it at the designated place after instal-
lation is nished.


Install the Plumbing
1. Install the drain in accordance with the manufacturer's
instructions.
NOTE: The distance from center of vanity drain hole to the
wall is 78 mm/81 mm (see roughing-in), and please choose
suitable drainage pipe.
Caution! Make sure a watertight seal exists on all basin
drain connections.
Caution! Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
Install the drain
Install the flexible pipe into the drain.
Fill up the gap between drain stub-out pipe with sealants.


 









Fig. 6 / 
CARE AND CLEANING 
Carefully read the cleaner product label to ensure the
cleaner is safe for use on the material.
Always test your cleaning solution on an inconspicuous
area before applying to the entire surface.
Wipe surfaces clean and rinse completely with water
immediately after cleaner application. Rinse and dry
any overspray that lands on nearby surfaces.
Do not allow cleaners to sit or soak on the surface.
Use a soft, dampened sponge or cloth. Never use an
abrasive material such as a brush or scouring pad to
clean surfaces.
Be careful not to leave staining materials in contact
with the surface for extended periods of time.
The ideal cleaner technique is to rinse thoroughly and
blot dry any water from the surface after each use.



 

 


 



ท่ออ่อน
Flexible Pipe
Pipe
รูท่อน้ำทิ้ง
Sealants.
Fig. 5 / 


 

E-mail: [email protected]
1358590-X2-A
KOHLER (THAILAND) PUBLIC COMPANY LIMITED
16th FL. Jasmine City Bldg., 2 Soi Sukhumvit 23, Sukhumvit Road, Wattana, Bangkok 10110 Thailand
Call Center Tel. +(66) 2700 9299 Fax. +(66) 2204 6224
ASIAN EMERGING MARKETS
Asia Customer Service Centre, Kohler Asia Pacic Limited
No.158, Jiang Chang San Road, Zhabei District, Shanghai, PRC. 200436.
Tel: +(86) 21 2606 2572 Fax: +(86) 21 6107 8900