Kohler MINIMA K-45805T User manual

13-1 528437
INSTALLATION INSTRUCTIONS
L
SLIDING, L SHAPE
8mm K-45805T
10mm K-45808T
MINIMA
-1-
, 2014
Copyright Kohler China Ltd., 2014
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
2
:(
). 80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1197575-T01-B

-2-
ROUGHING-IN
800-820-2628
IMPORTANT
800-820-2628
Before installation check that all components are
correctly supplied.
If any parts are missing please ring the helpline.
PARTS IDENTIFICATIONPARTS IDENTIFICATION
Unit: mm
Wall Channel
Wall Channel
Glass Clamp
Glass Clamp
Threshold
Splashguard
Inline Panel Top Lintel Door Panel Side Panel
H
B
C
1200-1600 700-1100 1850-2000
K-45805T
K-45808T
SKU B C H
1197575-T01-B

D
E
ABC
4mm Allen key
4mm
3mm Allen Key
3mm
Top Cap
X6
X3
X8
X2
X2 Wall Plugs
X8
Screw Covers
X8
Screw Covers
X8
Top Roller Clamps
X2
Mid-support Clamp
End Socket End-support Clamp
Bottom Guide
Plastic Guides Door Closing Guide
Support Strip
X2
Handle
-3-
Wedge
X2
Frame Cap,LH Frame Cap,RH
1197575-T01-B

-4-
·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Masonry Drill & 6mm Drilll Bit
Level
Drop Cloth
Materials Required
Tape
Silicone Sealant
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
6mm
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
INSTALLATION
STEP
1
Fit tray and then tile walls before fitting the unit.
Tray be level in all planes or the unit will not install properly.
IMPORTANT: MUST
NOTE: LH version shown, RH fitting is a mirror image of these instructions
0mm
20mm
1197575-T01-B

STEP
2
-5-
12
3
4
5
Wall channels
be
plumb.
MUST
Fit wall channels x2
x2
NOTE: Glass seal will
extend out of wall
channel.
A
X3
X3
X3
X3 6mm
20mm
STEP
3
53mm
Ensure the support strips are still on the bottom edge of the side panel, inside the H section, and that the H
section is 53mm from the corner of the glass.
53mm
1197575-T01-B

-6-
Caution
STEP
4
Glass needs to be at least 8mm into wall channel.
8mm
8mm minimum
8mm
Rest panel against seal of
wall channel.
Support panel until glass
clamp is fitted.
Panel needs to be parallel to
edge of tray.
Bottom channel
fits under seal.
STEP
5
C
X4
Fit glass clamp and turn screw until it lightly grips
glass.
1197575-T01-B

-7-
STEP
6
STEP
7
When glass is in correct position, fully tighten glass clamp screws, retighten screws after 10 minutes.
10
Make sure that distance between edge of glass and wall channel "A" outer corner projection is 15mm.
A 15mm
A
Glass
panel
be
plumb.
MUST
A
15mm
Ensure the support strips are still
on the bottom edge of the inline
panel, inside the H section, and
that the H section is 44mm from
the corner of the glass.
44mm
44mm
1197575-T01-B

-8-
Caution
STEP
8
Rest panel against seal
of wall channel "A".
A
Support panel until
glass clamp is fitted.
Bottom channel fits
under seal. Panel must be parallel
to edge of tray.
Glass needs to be at least
8mm into wall channel.
8mm
8mm minimum
8mm
A
C
STEP
9
X4
Fit glass clamp and turn screw until it lightly grips
glass.
STEP
10
When glass is in correct position fully tighten glass
clamp screws, retighten screws after 10 minutes.
10
Glass panel
be
plumb.
MUST
1197575-T01-B

=
=
STEP
15
Keep threshold position parallel to
tray edge.
-9-
STEP
12
STEP
11
STEP
13
53mm
Top view
Mark hole position
remove temporarily the
bottom guide and drill
hole into the tray.
6mm
Lay a bead of sealant in bottom guide as shown, then
slide it under glass.
2
STEP
14
Locate one end of threshold under the bottom guide.
1
1197575-T01-B

B
-10-
STEP
16
3
2
1
Caution
Lift side panel and fit end cap
guide.Lift Side Panel and Fit End
Cap Guide and Threshold Cover.
B
B
STEP
19
Screw bottom
guide to tray.
Top view
STEP
18
STEP
17
Cut seals exposed at top with
a sharp knife.
Fit top cap.
Fit screw
covers.
1197575-T01-B