Kohler Rada Tripoint-F 2.1658.011 User manual

111074257-W2-D
Tripoint-F
PRODUCT MANUAL
IMPORTANT
Installer: This Product Manual is the property of the
customer and must be retained with the product
for maintenance and operational purposes.

2
1074257-W2-D
Installations must comply with all Local/National Water Regulations/Bye-laws
(Scotland), Building and Plumbing Regulations.
Installation must be carried out in accordance with these instructions, and must be
conducted by designated, qualied and competent personnel.
Disinfectants: In applications where system chemical disinfection is practised,
chlorine can be used (calculated chlorine concentration of 50 mg/l [ppm] maximum in
water, per one hour dwell time), at service interval frequency. Such procedures must
be conducted strictly in accordance with the information supplied with the disinfectant
and with all relevant Guidelines/Approved Codes of Practice. If in any doubt as to
the suitability of chemical solutions, refer to Kohler Mira Limited, or your Local Agent.
When the battery has reached the end of its serviceable life, make sure the battery
is disposed of in a safe manner, in accordance with current local authority recycling,
or waste disposal policy.
IMPORTANT SAFETY INFORMATION
DESCRIPTION
The Rada Tripoint-F sensor deck mounted washbasin tap complies with all relevant
directives for CE marking. The Tripoint-F sensor tap can be installed as an adjustable,
a pre-set non-adjustable or for pre-mixed supply for most commercial applications.
SPECIFICATIONS
Pressures
Maximum Static Pressure 1000 kPa (10 bar)
Minimum Pressure Loss 200 kPa (2 bar)
Flow Rates and Times
Minimum Flow Rate (Flow Regulator Fitted) 6 L/min (300 kPa (3 bar))
Maximum Flow Period 2 minutes ±3 seconds
Intelligent After Flow Period 3 seconds ± 2 seconds
Temperatures
Maximum Hot Water 70 °C
Electrical
Power Supply 6 V lithium battery 2CR5
Sensor Recognition Range Optimal preset
Approvals
Noise Class I (ISO 3822)
IP Rating (Protection Class) IP67
Guarantee
We guarantee this product against any defect in materials or workmanship for a period of
one year from the date of purchase. For terms and conditions refer to the back cover.

311074257-W2-D
DIMENSIONS AND CHECKLIST
Tick the appropriate box after familiarising yourself with the tap and to conrm that all
the parts illustrated are included.
Note! All dimensions are nominal and in millimetres.
Documentation
1 x Product Manual
1 x Instruction Sticker
1 x Temperature Plug Cover
2 x Wall Plugs
2 x Fixing Screws
2 x Cable Ties
1 x 2.5 mm Hexagonal Wrench
1 x Flow Straighter + Washer
2 x 3/8’’ - 1/2’’ Adapters
2 x Filters
1 x Blanking Plug
2 x 3/8’’ Adapters/Check valves
1 x Cleaning Cover

4
1074257-W2-D
INSTALLATION
Installation Options
Note! Do not install opposite a mirror.
Adjustable
temperature outlet
Set for
xed temperature outlet
Using pre-mixed
temperature supply
Note! Turn to full cold and
block hot inlet.
Warning! Inlets have left
hand threads.
Blanking Plug

511074257-W2-D
Warning! Battery must be installed as
shown. Failure to do so will invalidate
warranty.
Minimum Ø30 mm
Maximum Ø37 mm
2
1
3

6
1074257-W2-D
4
Important! IMake sure
that the ats on the
connectors line up before
you install the cable

711074257-W2-D
Operate the tap and rotate the lever to adjust
the water to your required temperature.
5
This completes the tting of the Rada
Tripoint-F sensor tap.
OPERATION

8
1074257-W2-D
Setting the Rada Tripoint-F sensor tap for xed temperature ow
Operate the tap until the temperature of the water ow is stable and follow steps
1 to 4 to set the xed water temperature.
Operate the tap and check the water temperature is correctly set.
1
2
1
3
4

911074257-W2-D
Note! Isolate the water supplies and operate the tap to release pressure and to assist
the draining of residual water before any maintenance is carried out.
Cleaning the Filters
MAINTENANCE
Changing the Flow Straightener / Aerator
2
1
3

10
1074257-W2-D
FAULT DIAGNOSIS
Symptom Cause / Rectication
Continuous ow from the tap Solenoid valve damaged / Replace
Reduced ow from the tap Blocked lter or aerator / Refer to ‘Maintenance’
section
No ow from the tap Check the water supply and rectify
The sensor is covered, dirty, disconnected or
damaged / Clean, check the connections or replace
the sensor
The solenoid valve is damaged / Replace the
solenoid valve
The battery is at / Replace the battery
Cleaning
The tap should ONLY be cleaned using a mild washing up detergent or soap solution
and wiped dry with a soft cloth.
Note! To isolate the sensor, place cleaning cover over the sensor.
Cleaning Cover
Change the Battery
When the 2CR 6Volt battery has expired,
battery replacement should be carried out
with care.
DO NOT force the battery into the battery
box. Observe the shape of the battery box.
The battery should easily slip in and out of
the battery box.
DO NOT force the plug into the battery box
socket in reverse. Follow the alignment line
on the plug.
Warning! The
battery must be
inserted to match
the shape of
battery case.