Kohler K-T314 User manual

1012557-2-A2001 Kohler Co.
Español, Página 13
Français, Page 25

FINIAL FUNDAMENTALS
BATH/DECK-MOUNT BATH FAUCET
K-T314, K-T314M, K-T333, K-T333M
1. BEFORE YOU BEGIN
HOW TOUSE THESEINSTRUCTIONS
Please read these instructions carefully to familiarize
yourselfwiththerequiredtools,materials,andinstallation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based onthe latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time
without notice.
PRODUCTREQUIREMENTS
For roughing-in dimensions, see Fig. #1.
Ensure that any holes drilled in the deck are not
oversized. The spout requires adequate base
material strength. Spout and valve washers must
contact a maximumamountof decksurface.Spout
hole = 1” (2.5cm) maximum; and valve holes =
1-1/2” (3.8cm) maximum.
Finish deck material must fit closely to the
diameters of the plaster guards, especially the
spout plaster guard.
Ifholesaredrilledinthesheetdeckmaterialbefore
placement on the deck, they must match the
plaster guard diameters.
Plaster guard diameters are approximately 1-5/8”
(4.1cm) for the valve, and 13/16” (2.1cm) for the
spout.
Installer-supplied copper tubing is to be 5/8” O.D.
(1/2” nominal).
Provide an access panel to the valves from the
underside of the deck.
Install water hammer arrestors in the supply lines
near the valves.
INSTALLER INFORMATION
Observe all local plumbing and building codes.
Products purchased separately may influence
valve placement and alignment.
Spout will require that the spout supply tube be cut
to the proper length.
Instructions are given for installation with 8”
(20.3cm) centers. For installations wider than 8”
(20.3cm) centers, adjust all roughing-in
dimensionsandcoppertubinglengthsaccordingly.
These instructions cover two methods of
installation:installationonfinisheddeckorrim;and
installation on rough (unfinished) deck (to be
covered later with tile or other finish material).
Leave the protective sleeve on the spout supply
tube until the spout is installed. This is an O-ring
sealing surface, which may be damaged if
unprotected.
ORDERING INFORMATION
Bath/Deck-mount bath faucet:
Cross handles K-T314-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever handles K-T314-4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Tee handles K-T314-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross handles K-T333-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever handles K-T333-4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Tee handles K-T333-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOOLS AND MATERIALSREQUIRED
Open end/adjustable wrenches
Adjustable arc pliers
1/2” Nom. (5/8” O.D.) tubing
Tubing cutter
Hole cutting equipment
Soldering equipment and supplies
Phillips screwdriver

2
1012557-2-AKohler Co., Kohler, WI U.S.A.
ROUGHING-IN
Turn off the water supply.
Installor relocatethesuppliesas necessarytoconform to
the roughing-in dimensions.
* Dashed lines indicate items to be supplied by the
installer.
Diameter of the spout hole in the deck = 1” (2.5cm).
Diameter of valve hole in the deck = 1-1/2” (3.8cm).
NOTE: Reinforcingmaterial may be requiredifthedeckor
rim is thin. Install before proceeding.
NOTE: Forinstallationson a rough(unfinished)deckto be
covered later with tile, the tile thickness must not exceed
1-1/4” (3.2cm).
Fig. #1
2-3/8” (6cm)
1-5/16”
(3.3cm) D.
8” (20.3cm) Min.
2-1/8” (5.4cm) MAX.
ROUGH DECK
3/4” I.D.
9-1/2”
(24.1cm)
6-1/4”
(15.9cm) 7-1/2”
(19.1cm)
1/4” (6mm) TO 2-1/8”
(5.4cm) MAX. RIM OR
DECK MOUNT
1/4” (6mm) TO 1-1/4”
(3.2cm) MAX.
FINISHED DECK
ROUGH + FINISHED
DECK MOUNT INSTALLATION
RIM OR DECK MOUNT
INSTALLATION
7/8”
(2.2cm) D.
4-1/2”
(11.4cm)
1-1/4”
(3.2cm)
3-3/8” (8.6cm) 3-3/4” (9.5cm)
2-1/2” (6.4cm) TEECROSS LEVER
2-1/2” (6.4cm) 2-1/2” (6.4cm)
3-3/8”
(8.6cm)
4-1/2”
(11.4cm) 4-1/2”
(11.4cm)

31012557-2-A
Kohler Co., Kohler, WI U.S.A.
2. INSTALLATION ON FINISHED DECK OR RIM
NOTE: For installation on rough (unfinished) deck,
proceed to Section 3.
Preparation: For installations with 8” (20.3cm) centers
using copper tubing (1/2” nominal, 5/8” O.D.), cut the
tubing to the lengths as follows:
2 pieces: 2-7/8” (7.3cm) long
1 piece: 2-3/8” (6cm) long (for spout supply)
For non-8” (20.3cm) center installations, adjust the
tubing lengths as necessary.
NOTE: Leave the protective sleeve on the spout supply
tube until the spout is installed. This is an O-ring sealing
surface, which may be damaged if unprotected.
Install Spout Supply Tube: Slide a brass washer from
the bottom of the spout supply tube over the threads until
the washer reaches the supply tube shoulder.
Insert the spout supply tube through the mounting hole
from the top of the deck/rim. Ensure that the flat portion
of the washer faces forward. The supply tube will be
suspended by the washer.
Slide a brass washer onto the spout supply tube from the
bottom, and thread on the mounting nut. Tighten the nut.
NOTE: Do not use the supplied wood screws for
installation on finished deck or rim. Fig. #2
Supply Tube Shoulder Brass Washer
Brass Washer
Nut
Spout Supply Tube
Install Valve Bodies: Thread one mounting nut, flange
side up, onto each valve body.
NOTE: Rims less than 1/4” (6mm) thick require two
rubber washers in the following step; other installations
require only one rubber washer.
Slide one fiber washer, followed by one or two rubber
washers, onto each valve body.
Insert the 2-7/8” (7.3cm) long copper tubes between the
valvebodiesandthe1/2”tee.Theninsertthe2-3/8”(6cm)
long copper tube into the top of the tee.
DO NOT solder the connections yet.
Fig. #3
Rubber Washer
or Washers
Fiber Washer
Mounting Nut
Valve Body 2-7/8” (7.3cm)
Copper Tubes
2-3/8” (6cm)
Copper Tube 1/2”
Tee

4
1012557-2-AKohler Co., Kohler, WI U.S.A.
NOTE: Orient the valve body marked “COLD” so it is on
the right when you are facing the front of the faucet.
Insert the valve bodies through the mounting holes from
thebottomofthedeck/rim.Matethecoppertube from the
tee with the spout supply tube. Hold in place.
Setacollar, withtheflange side up,ontoeach valve body.
Thread down to at least 1” (2.5cm) from the top thread on
the valve body. Fig. #4
1” (2.5cm)
Collar
Tighten the mounting nuts on each valve body from
underneath the deck/rim.
Solder the copper tubes to the valve bodies, tee, and
spout supply tube.
Solder the hot and cold water tubes to the valve body
inlets. Ensure that the cold supply is on the right side.
NOTE: Proceed to Section 4.
Fig. #5
Solder
Hot
Supply Solder
Cold
Supply
Solder
3. INSTALLATION ON ROUGH (UNFINISHED) DECK
Preparation: For installations with 8” (20.3cm) centers
using copper tubing (1/2” nominal, 5/8” O.D.), cut two
pieces of tubing to 2-7/8” (7.3cm) in length.
Fornon-8”(20.3cm) centerinstallations,adjustthetubing
lengths as necessary.
NOTE: Leave the protective sleeve on the spout supply
tube until the spout is installed. This is an O-ring sealing
surface which may be damaged if unprotected.
Install Spout Supply Tube: Slide a brass washer from
the bottom of the spout supply tube over the threads until
thewasherreachesthesupplytubeshoulder.Ensurethat
the countersunk holes in the washer are facing upward.
Insert the spout supply tube through the mounting hole
from the top of the deck. Ensure that the flat portion of
washer faces forward.The supplytube willbe suspended
by the washer.
Slide a brass washer onto the spout supply tube, and
thread on the mounting nut. Tighten the nut.
Secure the brass washer to the deck using the two
supplied wood screws. Fig. #6
Brass
Washer
ScrewScrew
Supply Tube
Shoulder
Brass
Washer
Nut
Spout Supply Tube
Rough
Deck

51012557-2-A
Kohler Co., Kohler, WI U.S.A.
Install Valve Bodies: Thread one mounting nut, flange
side up, followed by one fiber washer and one rubber
washer onto each valve body.
Insert the 2-7/8” (7.3cm) long copper tubes between the
valve bodies and tee.
DO NOT solder the connections yet.
Fig. #7
Rubber Washer
Fiber Washer
Mounting Nut
Valve Body
1/2” Tee
2-7/8” (7.3cm)
Copper Tubes
NOTE: Orient the valve body marked “COLD” so it is on
the right when facing the front of the faucet.
Insert the valve bodies through the mounting holes from
the bottom of thedeck. Matethecopper tubefrom thetee
with the spout supply tube. Hold in place.
Setacollar, withtheflange side up,ontoeach valve body.
Thread down to at least 1” (2.5cm) from the top thread on
the valve body. Fig. #8
1” (2.5cm)
Collar
Set Valve Body Height: Use one of the following two
formulas to calculate the valve body clearance required
for the finish material at your site.
Addthetile thickness to 1-1/4” (3.2cm)(distancerequired
from the finished deck to the top of the valve threads), if
the tile is less than 1” (2.5cm) thick.
Example #1: Tile thickness 3/4” (2cm) + 1-1/4” (3.2cm)
= 2” (5cm) clearance.
If the tile thickness is between 1” (2.5cm) and 1-1/4”
(3.2cm), add only 1” (2.5cm) to the 1-1/4” (3.2cm)
distance.
Example #2: Tile thickness 1” (2.5cm) + 1-1/4” (3.2cm)
= 2-1/4” (5.7cm) clearance.
Adjustthethreadedcollaruntilthedimensionfrom thetop
of the valve threads to the top of the rough deck surface
equals the clearance requirement you calculated.
Note this dimension. You will need to use it again after
connecting the supply tube.
Fig. #9
ÀÀÀÀ
ÀÀÀÀ
ÉÉÉÉ
ÉÉÉÉ
Tile
Thickness
2-1/8”
(5.4cm)
Max.
2” (5cm)
1-1/4” (3.2cm) Top of Valve
Threads Threaded
Collar
Rough
Deck
3/4” (2cm)
EXAMPLE #1

6
1012557-2-AKohler Co., Kohler, WI U.S.A.
Supply Tube Connection: Measure the distance from
the bottom of the spout supply tube to the top of the tee.
Add 1” (2.5cm) to this measurement, and cut a piece of
1/2”nominal(5/8”O.D.)coppertubingtofitintothesupply
tube and tee port.
Back off the threaded collars as far as possible without
removing them. Pivot the valve bodies enough to remove
the tee and two pieces of tubing. If the valve body holes
are smaller than recommended, it may be necessary to
remove the entire valve body assembly.
Install the tubing into the tee. Mate the copper tube from
the tee with the spout supply tube. Pivot the valvebodies
onto the two pieces of copper tubing.
DO NOT solder at this time.
Fig. #10
Threaded
Collar
Rough
Deck
Mounting
Nut Copper
Tube
Spout
Supply
Tube
Tee
Reset Valve Body Height: Adjust the threaded collars
untilthedimensionfrom thetopof thevalvethreads tothe
top of the rough deck surface equals the clearance
requirement you calculated in Fig. #9.
Fig. #11
ÀÀÀÀ
ÀÀÀÀ
ÉÉÉÉ
ÉÉÉÉ
Tile
Thickness
Threaded
Collar
Rough
Deck
Pre-determined
Clearance
Requirement
Top of Valve Threads
Tightenthemountingnutsoneachvalvebodyunderneath
the deck.
Solder the copper tubes to the valve bodies, tee, and
spout supply tube.
Ensure that the cold supply is on the right side.
Solder the hot and cold water supply tubes to the valve
body inlets.
Fig. #12
Solder
Cold
Supply
Solder
Hot
Supply
Mounting
Nut Solder
Copper
Tube
Rough
Deck
Spout
Supply
Tube
Valve
Body

71012557-2-A
Kohler Co., Kohler, WI U.S.A.
4. VALVING CHECKOUT (ALL INSTALLATIONS)
Thread a 1/4” pipe plug into the top of the spout supply
tube.
Ensure that the valves are closed (cold - fully
counterclockwise, hot - fully clockwise).
Turn on the main water supply, and check the complete
installation for leaks with the valves closed and open.
Repair leaks as required.
Close both valves. Turn off the main water supply.
1/4” Pipe Plug Close
Cold
Close
WARNING: Risk of personal injury. Lines will be
pressurized. Do not lean over pipe plug when
turning or removing the plug.
Close
Hot
Wrapatowelaroundthe pipeplugto preventwaterspray.
Water will purge from the supply tube when you remove
the plug.
Carefully back out the pipe plug to relieve pressure.
Thread the pipe plug back into the spout supply tube.
Leave the pipe plug installed until the spout and handle
are installed.
Install the cardboard plaster guards over both valves and
the spout supply tube. Leave in place until the spout and
handle are installed.
Fig. #13
5. INSTALL TILE (IF APPLICABLE)
Verify that there will be a 1-1/4” (3.2cm) distance fromthe
top of the sleeve to the top of the tile. If not, do not install
the tile due to improper valve installation.
If proper clearance exists, install tile up to the plaster
guards on the valves and the spout supply tube.
Fig. #14
Threaded
Collar
Rough
Deck
Tile Spout
Supply
Tube

8
1012557-2-AKohler Co., Kohler, WI U.S.A.
6. BEFORE INSTALLING SPOUT AND HANDLES
REMOVEPIPEPLUG
Ensure that the valves are closed (cold - fully
counterclockwise, hot - fully clockwise).
Turn off the main water supply.
1/4” Pipe Plug Close
Cold
Close
Hot
WARNING: Risk of personal injury. Linesmaybe
pressurized. Do not lean over pipe plug when
turning or removing the plug.
Wrapatowelaroundthe pipeplugto preventwaterspray.
Water may purge from the supply tube when you remove
the plug.
Carefully remove the pipe plug. Fig. #15
7. INSTALL SPOUT
Remove the plaster guard from the spout supply tube.
Cutoffthespoutsupplytube1-1/4”(3.2cm)abovetherim,
finished deck, or tile.
Ensure that all burrs are removed from the supply tube to
prevent damage to the O-ring seal on the sleeve.
Fig. #16
1-1/4” (3.2cm)
Tile
Finish
Rough
Deck
NOTE: The following step is applicable to a tile covered
rough deck installation only.
Slide a brass washer, flat side facing forward, onto the
supplytube.Thebrasswasherisfurnishedwiththespout.
NOTE: The washer is not needed for rim/finished deck
installation.
Fig. #17
Spout
Supply
Tube
Rough
Deck
Finished
Deck
Washer

91012557-2-A
Kohler Co., Kohler, WI U.S.A.
Back off the setscrews in the sleeve, and with a twisting
motion install the sleeve on the spout supply tube until it
contacts the washer surface.
Align the sleeve so the setscrews are not facing directly
forward or backward.
Tighten the setscrews.
Whensupplied,positiontheringoverthesleevesoitrests
upon the washer. Fig. #18
Setscrew
Setscrew
Sleeve
Apply a ring of plumbersputty or other sealantaround the
underside of the spout according to the putty
manufacturer’s instructions.
Fig. #19
Spout
Apply Plumbers Putty
Î
CAUTION: Risk of product damage. Use care
when installing the spout assembly to prevent
damage to the O-ring seal on the sleeve.
Install the spout assembly onto the sleeve, and carefully
pressdownuntilthespoutbasecontactsthedeck, rim, or
tile.
Align the spout as desired, and tighten the setscrew.
If included, press the plug button into the setscrew hole.
Fig. #20
Setscrew
Plug
Button
Î

10
1012557-2-AKohler Co., Kohler, WI U.S.A.
8. INSTALL HANDLES
Remove the plaster guards from the hot and cold valves.
Fig. #21
Install a stem extension onto each valve stem spline.
Ensure that the splines are properly aligned.
Fig. #22
Valve Stem Spline Stem Extension
Valve Body
NOTE: There are several handle styles available for this
product. For illustrative purposes, only the Cross handle
is shown. Installation of the different handle styles is
identical.
Install the handle assembly by threading onto the valve
body. Take care that the splines inside the skirt and stem
extension are engaged. Adjust as required.
NOTE: The stem extension allows for fine adjustment of
handle alignment. To refine the alignment, unthread the
handle assembly, and reposition the stem extension on
thevalvestem.Rethreadthehandleassembly,andcheck
the handle alignment. Repeat until the alignment is
satisfactory. Fig. #23
Handle
Assembly
Stem Extension