Kohler MEMOIRS User manual

, 2013
Copyright Kohler China Ltd., 2013
MEMOIRS
SINGULIER
INSTALLATION INSTRUCTIONS
8mm
HINGED, ANGLE, 1DR2PAN, 8mm
K-36938T/K-36952T
10mm
HINGED, ANGLE, 1DR2PAN, 10mm
K-36945T/K-36959T
-1-
13-1 528437
·
·
·
·
·
·
2
80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should fall
above 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1146426-T01-B

-2-
ROUGHING-IN
Unit: mm
PARTS IDENTIFICATIONPARTS IDENTIFICATION
BCHSKU
H
B
C
K-36938T
K-36952T
K-36945T
K-36959T
800-1200 800-1200 1850-2000
K-36938T/K-36945T
MEMOIRS Bracket Assy
X2
MEMOIRS Handle Assy
MEMOIRS Wall Clip Assy
X4
MEMOIRS 135 DEG Hinge Assy
135 X2
MEMOIRS Bottom Clip Assy
X2
MEMOIRS Wall Clip Body Cover
X4
Special Key
X1
Cover
X8
4mm Allen Key
4mm
X5
X5
X2
Hinge Cover
X10
SINGULIER Bracket Assy
X2
SINGULIER Handle Assy
SINGULIER Wall Clip Assy
X4
SINGULIER 135 DEG Hinge Assy
135 X2
SINGULIER Bottom Clip Assy
X2
SINGULIER Wall Clip Body Cover
X4
Frame Cap, 135 LH
()X1
°
135°Frame Cap, 135 LH
()X1
°
135°
Frame Cap, 135 RH
()X1
°
135°Frame Cap, 135 RH
()X1
°
135°
Special Key
X1
Cover
X8
4mm Allen Key
4mm
X5
X5
X2
Hinge Cover
X10
K-36952T/K-36959T
1146426-T01-B

-3-
STEP
1
Fix the gasket to the glass.
STEP
2
Affix the wall clip to the glass ,screws not locked.
Note: Please
insert the glass
in the correct
direction.
INSTALLATION
STEP
3
Fix the wall clip and the floor clip.
30
30
6mm
6mm
1146426-T01-B

STEP
5
STEP
4
Align the glass to level, and lock the wall clip and the
floor clip.
Complete the glass installation of the other side
following the same steps.
If the door opens inward, please first insert the
gasket into the glass.
Affix the hinge to the hole on top of the glass,
screws not locked.
Be aware of the direction
of the hinge: The upper
part should be fixed to the
glass.
STEP
6
STEP
7
-4-
Skip this step if the door
opens outward.
1146426-T01-B

+1mm
Align the cam with tools to up the hinge to level, then
lock the screws.
Tips: there are two
holes on the surface
of the cam, the
bigger one and the
smaller one
separately mark the
highest and the
lowest point of the
cam.
STEP
8
-5-
Affix the hinge to the hole on the bottom of the glass,
screws not locked.
STEP
9
STEP
10
Take down the hinge platen.
STEP
11
Aim the door glass at the hole location and affix it to
the hinge, and install the hinge platen, crews not
locked.
Be auare of the
direction of the hige:
The upper part should
be fixed to the glass.
1146426-T01-B

STEP
12
Align the cam with tools to level the glass, then lock
the screws.
Tips: there are
two holes on
the surface of
the cam, the
bigger one and
the smaller one
separately mark
the highest and
the lowest point
of the cam.
0mm
-6-
STEP
13
Fix the handle.
STEP
14
STEP
15
Install bottom frame channel and cap.Fix the bottom gasket.
1146426-T01-B

STEP
19
-7-
STEP
16
If the door opens unwell, please loosen the wall clip
and the floor clip slightly, adjust the glass until the
door closed completely, then lock the screws.
Fix the magnetic stripe and the gasket.
Be aware of the
direction of the magnetic
stripe and the gasket.
STEP
17
Fix the tierod.
0mm 0mm
STEP
18
Fix the cover caps to the wall
clips.
1146426-T01-B

STEP
20
Fix the cover caps to the hinges.
-8-
STEP
22
Fix the bottom of the glass and use the water-
resistant gel.
STEP
21
Do not use the enclosure for at least 24 hours.
24
24hrs
1146426-T01-B