Kohler Englefield EVORA Back-to-Wall User manual

1265059-A2-D June 2016
INSTALLATION
INSTRUCTIONS
TOILET
EVORATM Back-to-Wall
Nov 2020 1
1294931-A2-D
With an Englefield toilet suite
you can be sure of having
excellence, comfort, durability
and style.
It’s the details that Englefield
cares about - from pioneering
the latest technology, to
innovative design.
NOTE: The Evora Back-to-Wall toilet suite is suitable for both
a rear & side entry water inlet.
TM

CAUTION: Risk of personal injury or product damage. Handle
with care. Vitreous china can break or chip if the product is handled
carelessly.
Observe all local plumbing and building codes. Installation shall be in
accordance with AS/NZS 3500 and AS/NZS 6400.
Carefully inspect the new toilet for damage.
If the existing toilet does not have a supply shut-off valve below the
cistern, install one before installing the new toilet.
Install sufficient backing behind the finished wall to provide a secure
material for the anchoring devices.
Water supply hose not supplied. Your plumber can provide a suitable
hose of sufficient length from the shut-off valve to the tank inlet.
WARNING: Ensure that no part of the cistern inlet hose is submerged in water.
INSTALLATION INSTRUCTIONSEVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
BEFORE YOU BEGIN
ENGLEFIELD
2
Before proceeding with installation, please read these instructions carefully
to familiarise yourself with the required tools, materials and installation
sequences. Please leave these instructions for the consumer after
installation.
Prior to installation, inspect the toilet to ensure that no damage has
occurred in transit. If damage has occurred, or a visible defect exists,
do not proceed with installation, and advise your supplier immediately.

250mm hose for
Top/Rear install
(supplied with cistern)
Side Inlet Valve
(for Top Rear Entry.
Supplied with cistern)
Caulking Gun
Adjustable Pliers
Metal File
1/2” Socket
Hacksaw
Silicone Sealant
Pencil
Screwdriver
Safety Glasses
Tape MeasureAdjustable
Spanner
Level Pipe Wrench
Tube Cutter
Sponge
Drill & Bits
Side Entry
Capping Plug
Pan Fixing Kit
(supplied)
Water Supply Hose
(not supplied)
Cistern Bung
(supplied with cistern)
Shut-off Valve
(not supplied)
Vario Connector
(supplied)
Bottom Inlet Valve
(supplied with cistern)
INSTALLATION INSTRUCTIONS
ENGLEFIELD
2
TOOLS AND MATERIALS REQUIRED
Back-to-Wall Toilet Suite
ENGLEFIELD
3
PARTS IDENTIFICATION
EVORA
TM

3
1 Remove the existing toilet: Turn off the water supply and flush the toilet,
then sponge out all remaining water from the cistern. Disconnect the supply
hose from the shut-off valve and remove the old pan and cistern.
CAUTION: Risk of hazardous gases. Temporarily stuff a rag in the closet
flange. Ensure this is removed before installing the new toilet.
Identify the type of toilet installation:
A) Side Entry with Bottom Inlet or B)Top Rear Entry with Side Inlet Valve.
For Side Entry toilets, the bottom inlet valve is supplied with the cistern.
Bottom
Inlet
Valve
Bottom
Inlet
Side
Inlet
Valve
2
For Side Entry/Bottom Inlet installations, check the shut-off valve position.
Left-hand
valve position
Right-hand
valve position
Shut-off
valve Shut-off
valve
Side entry hole
For Top Rear Entry installations, skip toPan Installation on page 6.
For Side Entry/Bottom Inlet installations, proceed with instructions, below.
B) Top Rear Entry
cistern configuration
Cistern
Inlet Hose
Top Rear
Entry
Bung
Side entry hole
NOTE:For shut-off valves positioned on the right-hand side,
a longer water supply hose may be required (not supplied).
WARNING: Ensure that no part of the cistern inlet hose is submerged in water.
Captive
Nut
(in pan)
Captive
Nut
(in pan)
A) Bottom inlet
cistern configuration
ENGLEFIELD
4
INSTALLATION INSTRUCTIONS
Back-to-Wall Toilet Suite
PREPARING TO INSTALL
EVORA
TM

3 Position the cistern on the pan
by centering the gasket on the
pan inlet. Securely tighten the
screws so the cistern is level.
4 Connect the supply hose to
the cistern inlet and feed the
hose through the appropriate
side hole in the pan.
5 Connect the supply hose tothe shut-off valve totest the system
for leaks. Shut off the water supply and disconnect the hose. Insert a
capping plug into the unused hole.
1 Remove the Side Inlet valve and 250mm hose.
2 Install the Bottom Inlet valve tothe cistern. Discard the bung. Place
the washers over the fixing screws and locate in cistern fixing holes.
Capping Plug
Water Supply Hose
(Not supplied)
Gasket
Screw
Pan Inlet
NOTE:
Bottom Inlet Valve
has been preset to
deliver a full flush
volume of 4.5L.
Side Entry Holes
Bottom
Inlet
Valve
Washer
Seal
Nut Captivated Nut
(in pan)
Rubber Seal
Washer
Fixing Screw
CISTERN INSTALLATION - BOTTOM INLET
ENGLEFIELD
4
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
5
Skip this page if installing a
Top Rear Entry cistern configuration.

2Using the template, mark the positions of the floor fixing kit holes.
PAN INSTALLATION
ENGLEFIELD
6
Template
Fixing hole
locations
Wall
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
1 The pan can be installed as P-Trap or S-Trap.
For S-Trap installations please use the supplied Vario Pan Connector, and
follow the included instructions.
For P-Trap installations the straight pan connector is not supplied.
P-Trap Finished
Wall
Pan
Straight Pan
Connector Setout
S-Trap Finished
Wall
Vario
Connector
Pan
Waste Pipe
Setout
(90-120mm)

4
5
6
Place a washer onto each of the hexagon screws and fix the brackets
to the floor.
Position the toilet in the marked location, while ensuring an effective
connection is made with the pan connector.
Install the plastic screw sleeves and use the screws to fix the
toilet to the brackets. Attached the chromed caps to the screw heads.
For Side Entry/Bottom inlet installations, skip to Push Button Installation on page 9.
For Top Rear entry installations, proceed to Cistern Installation on page 8.
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
7
3 Drill fixing holes at the marked locations on the floor and insert the
anchors where required.
Anchor
Screw
Sleeve
Hole
Cap
Hexagon
Lag Screw
Bracket
Washer
Anchor

4 Insert capping plugs into the side entry holes in the pan.
1 Securely install the bung into the bottom inlet of the cistern. Place
the washers over the fixing screws and locate in cistern fixing holes.
2
Skip this page if installing a
bottom inlet cistern configuration.
Bung
Seal
Washer
Nut
Captivated Nut
(in pan)
Seal
Washer
Fixing Screw
Position the cistern on the pan
by centering the gasket on the
pan inlet. Securely tighten the
screws so the cistern is level.
3 Connect the supply hose to
the cistern inlet and connect the
hose to the water supply
shut-off valve.
Gasket
Screw
Pan Inlet
5Connect the supply hose tothe shut-off valve totest the system
for leaks. Shut off the water supply and disconnect the hose.
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
8
CISTERN INSTALLATION - TOP REAR ENTRY
Cistern Inlet
Hose
(supplied)
Side Entry Holes

1 Disassemble the push rods. 2 Using the push rod, measure
the distance between the flush
valve and the top of the cistern
lid. Mark this length and cut the
push rod to length.
3 Reassemble the push rods. 4 Fit the lid and test the buttons.
Adjust the rods as required.
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
9
PUSH BUTTON INSTALLATION

2
Flush Valve B
1
2
Flush Valve A
1
1
2
1
2
Release flush valve by turning
anti-clockwise and pulling straight
up on the canister.
Release flush valve by
squeezing the tabs on both
sides of the canister and pulling
straight up out of the flush
valve.
Assemble flush valve by pushing
straight down into the canister
and turning clockwise.
Assemble flush valve by
pressing it into the flush valve so
it snaps into place.
INSTALLATION INSTRUCTIONS
EVORA
TM
Back-to-Wall Toilet Suite
ENGLEFIELD
7ENGLEFIELD
10
FLUSH VALVE REMOVAL AND INSTALLATION