Kohler K-5724K User manual

1456686-X2-A

1456686-X2-A 1 Kohler Co.
Adjustable Wrench Screw driver
Tools and Materials
Before You Begin
Roughing-in
WARNING: Risk of scalding. High water temperature can cause severe burns. Do
not connect this device to a water supply with a maximum temperature above 104°F
(40°C).
Observe all local plumbing, electrical, and building codes.
Only connect the seat to a cold water supply of drinking quality at a pressure of 20 (139 kPa)
- 80 psi (551 kPa).
Dimensions are approximate.
Unit: mm
17-11/16" (449 mm)
11-3/4"
(298 mm)
8-1/8"
(206 mm)
4-3/8"
(111mm)
7/8"
(22 mm)
14-5/16" (364 mm)
18-11/16"
(475 mm) 20-1/2"
(521 mm)
2-1/8"
(54 mm)
Min
13-1/4"
(337 mm)
5-1/2"
(140 mm)
Min
Finished wall
Finished wall

2. Install the Seat
1456686-X2-A2Kohler Co.
1. Install the Mounting Plate
Position the Seat
Slide the seat onto the mounting plate until you feel it snap into plate.
Check the positioning of the seat. Adjust the position if needed.
Adjust the Seat
To adjust the seat position, remove the seat by pressing in the release button and sliding the
seat forward.
Reposition the mounting plate as needed.
Install the Seat
Securely tighten the mounting plate bolts and nuts.
Slide the seat onto the mounting plate until you feel it snap into plate.
Position the mounting plate over the mounting holes on the bowl.
Position the washers to rest in the openings of the mounting plate.
Insert each bolt through the mounting plate and into the mounting holes.
NOTE: The nut should not be threaded onto the bolt. It will not tighten by threading it into place.
While holding the bolts in place, push a nut up onto each bolt as far as possible.
Bolt
Mounting Plate
Washer
Nut
Release
Button
Mounting
Plate

3. Connect the Water Supply
CAUTION: Risk of property damage. Do not push or pull on the water connection
between the seat and the water supply stop. This will prevent water leakage.
NOTICE: Use care to avoid cross threading or overtightening the connections. Unless other-
wise indicated, use an adjustable wrench to tighten one-quarter turn past hand-tight.
Connect the T-valve to the seat hose.
If needed, connect the supply hose to the supply stop.
Connect the supply hose to the T-valve.
Install the seat hose to the orange colored inlet.
IMPORTANT! The white cap must be in place on the side opposite the seat hose.
Connect the T-valve to the water inlet on the toilet tank.
Turn on the water supply.
Check all connections for leaks and make any adjustments as needed.
3
Or
Supply Stop
T-Valve
Filter Filter
Hose
Supply Hose
1456686-X2-A Kohler Co.
Confirm the filter is in place. Install if needed.

4
Care and Cleaning
For best results, keep the following in mind when caring for your KOHLER product:
• Always test your cleaning solution on an inconspicuous area before applying to the entire sur-
face. Avoid using aerosol products.
• Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse
and dry any overspray that lands on nearby surfaces.
• Do not allow cleaners to soak on surfaces.
• Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or
scouring pad to clean surfaces.
•
contact with the seat.
• The ideal cleaning mixture is dishwashing soap and water. Rinse and dry with a soft cloth.
For detailed cleaning information and products to consider, visit www.kohler.com/clean.
Do not allow chemicals and cosmetics (such as fingernail polish and aftershave) to come in
Operation
IMPORTANT!Water can spray when on one is sitting on the seat.
Do not activate the water until seated.
To activate the spray wand, twist the handle away from you.
To control the water flow, twist the handle away from you to increase the flow, toward you to
decrease the flow.
To adjust the spray wand position, push the handle down until the desired position is found.
To turn the spray wand off, twist the handle toward you until it stops.
1456686-X2-AKohler Co.

Removing the Seat
Turn the water supply off.
Press the button on the right side of the seat, located near the water inlet.
Slide the seat forward.
5
Nozzle Options
NOTE: Two additional nozzles are provided. Each has a different spray intensity. Choose the
nozzle that best suits your needs.
Nozzle 1 - Comes installed. Mid level intensity.
Nozzle 2 - Soft spray. For users who prefer a gentle spray or homes with high water pressure.
Nozzle 3 - Intense spray. Best for installations with low water pressure.
Changing the Nozzles
Manually pull the wand out.
Firmly grip the wand, then pull the nozzle and remove.
Select the replacement nozzle.
place.
Release Button
1456686-X2-A Kohler Co.
Nozzle 1
Nozzle 2
Nozzle 3
With the outlet holes facing up, grasp the wand and firmly push the replacement nozzle into

8 1456686-X2-AKohler Co.

1456686-X2-A Kohler Co.9