Kohler OVE K-17629T-2 User manual

OVE
INSTALLATION INSTRUCTIONS
ONE-PIECE TOILET
K-17629T-2/K-17629T-S2
-1-
NOTES
·
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
Ensure that the new drain has the correct roughing-in
dimension.
Carefully inspect the new fixture for any sign of damage.
: Handle vitreous china products very carefully.
Vitreous china can break and chip if you over tighten
bolts and nuts.
. The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten 1/4 turn past
finger tight.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2018).
This product complies with Q/KCI-006-2018 and GB
25502-2017. Water Efficiency Grade 2.
·
WARNING: Risk of personal injury or product
damage
WARNING: Risk of external leakage
·
·
·
·
·
·
ASME (A112.19.2-
2018)
Q/KCI-006-2018 GB 25502-2017
2
1/4
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
·
·
·-
ORDERING INFORMATION
OVE Toilet..............................................................K-17629T-2
Includes K-17669T-M
OVE Toilet ...........................................................K-17629T-S2
Includes K-17660T-M
OVE Toilet Seat...............................
OVE Quiet-close Toilet Seat ............
®
®
.............................................................K-17629T-2
...............................K-17669T-M
...........................................................K-17629T-S2
........................K-17660T-M
©
©
Copyright Kohler China Investment Co., Ltd. 2020
2020
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410
8 256410
NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400
1 110400
:
POST CODE:
POST CODE:
1089093-T01-H

TOOLS AND MATERIALS REQUIRED
(Not supplied)
·
·
·
·
·
·
·
·
·
·
·
·
·
(10") adjustable wrench
Supply shut-Off valve
Tape measure
Level
Sponge
Pipe wrench
Tubing cutter
Safety Glasses
Drill and assorted bits
Connector
Metal file
Hacksaw
1/2" Nut Driver/Socket
()
·
·
·
·
·
·
·
·
·
·
·
·
·
10"
1/2"
-2-
Unit: mm
:
With 1226681 S-trap Way
1226681
O36
350 370
730
390
700
305
102
185
245
40
Button
65
165
174
28
O11
Kohler reserves the right to change marked dimensions without prior notice.
Finished
Wall
Reference Value
475
140
1089093-T01-H

-3-
INSTALLATION
1. Remove the Existing Toilet
·
·
·
Turn off the water supply.
Flush the toilet, then sponge out all remaining water from
the tank.
Disconnect the supply shut-off valve(if present), and
remove the old bowl and tank.
CAUTION: Risk of hazardous gases. If the new toilet
is not installed immediately, temporarily stuff a rag in
the closet flange.
1.
·
·
·
()
()
2. PREPARE THE SITE
Position the template on the floor.
Trace around the template on the floor with a pencil.
Mark the mounting hole centerline on the floor.
2.
Finished Wall
3. Connect the Supply Hose
·Put inlet pipe(500mm recommended, not supplied)
throught the inlet pipe cover assembly and connect it with
the fill valve.
3.
·( 500mm )
Water Supply Hose
Rear Bowl
BACK BACK
1089093-T01-H

-4-
4. DEFINE THE POSITION OF S-TRAP 4.
5. INSTALL THE NEW PAN
Place the pan and push up against the wall.
Check the mounting hole with pan on the floor.
Carefully remove the pan from the installation area.
Drill 3/8(10mm) mounting holes between the marked
locations on the floor and insert the anchor.
: Overtightening
may cause breakage or chipping of the vitreous China.
Install the washer over the bracket and insert the hexagon
screw into the bracket through the washer then tighten the
screw.
Align the pan back to position over the brackets.
Install the sleeves and tighten the screw.
Attach the caps.
CAUTION Risk of product damage.
5.
10mm
Water Supply Hose
Screw
Hole
Sleeve
Hexagon
Lag Screw
Bracket
Washer
Anchor
Cover
1226681
S-Trap 305
102
185
245
Finished
Wall
1089093-T01-H

7. ADJUST OVERFLOW HEIGHT (If
necessary)
Adjust overflow tube so that the top is 20mm above the
waterline. Push locking mechanism to the side and adjust
tube height. Push locking mechanism back into position to
lock tube height.
7.
20mm
1
Maxi
2
6. CONNECT THE SUPPLY
Connect the supply shut-off valve to the supply hose and
connect supply hose to toilet supply shank.
Open the supply shut-off valve slowly to check for leaks. If the
connections have been properly assembled, a slight
tightening of the nuts should stop leakage.
Flush the toilet several times using first one push tutton and
then the other, and check all connections for leaks. Verify
proper operation.
Periodically check for leaks for several days following the
installation.
Adjust the float by the cross-shaped thread and sliding itup or
down on the float rod until the water level is at the marked
water line.
6.
-5-
Supply Shut-Off Valve
Connection
Water
Supply
Hose
Supply
Shut-off
Valve
1089093-T01-H

-6-
9.
·
9. Install the Seat
·Install the toilet seat according to the packed instructions.
8. Install And Adjust Push Buttons
(1) Fix tank cover onto the tank.
(2) Unscrew the big white nut on the push button and insert
the button into the hole on the tank.
(3) Test the push buttons.
1) No need for any adjustment if the rods just touch the
push buttons on the flush valve.
2) If the rods are tightly against the push buttons on the
flush valve, take out the buttons, loosen the small nuts
and screw clockwise until the rods just touch the push
buttons on the flush valve.
3) If the rods cannot touch the push buttons on the flush
valve, take out the buttons, loosen the small nuts and
screw anticlockwise until the rods just touch the push
buttons on the flush valve.
(4) Take out the buttons and tighten the small nuts.
(5) Tighten the big nut from inside the tank.
(6) Test flush several times to check for leakage.
8.
(1)
(2)
(3)
1)
2)
3)
(4)
(5)
(6)
Push Button
Tank Cover
Rubber Sleeve
Small Nut
1089093-T01-H

This troubleshooting guide is for general aid only.
If the problem is water continuously running into the toilet, turn off the water supply to the toilet. If the water
level in the tank lowers, replace the seal of the flush valve. If the level in the tank remains constant, replace the float valve.
Note: Do not flush.
1. Poor flush. A. Adjust tank water level to match waterline.
B. Fully open water supply shut-off valve.
C. Clear obstruction in trapway, jet, or bowl rim holes.
D. Clear obstruction in soil pipe or vent pipe.
3. Fill valve turns on/off by itself without toilet
being flushed, or runs allowing water to enter
tank.
A. Clean or replace seal if seal is worn, dirty, or misaligned with flush valve
seat or flush valve seat is damaged. Replace flush valve seal or flush
valve.
B. Remove tank and tighten flush valve nut if flush valve gasket is leaking.
Do not overtighten. If leakage continues, replace gasket.
C. Clean fill valve seat/seat washer of debris, or replace piston/seat
washer assembly.
D. Replace fill valve if valve float sinks.
E. Adjust tank water level if too high.
2. No flush. A. Remove the canister out of the flush valve and check mechanic system.
If it has some part damage, replace the new canister on the flush valve.
B. Adjust push rods to position properly on flush valve.
4. Long tank fill cycle. A. Fully open water supply shut-off valve.
B. Clean fill valve inlet, valve head, or supply line. Flush lines.
5. Noisy tank fill cycle. A. Partially close the water supply shut-off valve if water pressure to the
toilet is too high. Check toilet performance following any such
adjustment.
B. Remove dirt or obstruction in valve head, flush line.
2. A.
B.
4. A.
B.
3. / A.
B.
C. /
D.
E.
1. A.
B.
C.
D.
5. A.
B.
-7-
1089093-T01-H

(
)()
()
()
0C
o
CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in
the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to clean
as far into the trap as possible to prevent mineral deposits
from forming.
Most toilet bowl cleaners are not harmful to the vitreous china
surface of the toilet bowl. Please follow the bowl cleaner
manufacturer is instructions carefully.
Do not use abrasive cleaners or solvents.
Do not use in-tank cleaners. Products containing
chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage
and property damage.
Kohler Company shall not be responsible or liable for any
damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite).
WARNING: Risk of property or product damage.
'
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
CAUTION:
CAUTION: Don t use any cement while installing
the toilet.
WARNING: Risk of product damage.
Heat expansion of the toilet may damage
the feet of the toilet. Kohler will not be responsible for
any damage because of using cement.
Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.
o
-8-
1089093-T01-H