Koliber S1 User manual

www.eurosafes.eu
Koliber Strong safes, grade S1
Koliber Strong safes
Application:
Koliber Strong safes are modern, high-quality models of safes created for storing jewelery, weapons, ammunition as
well as for storing portable computers. The products of the Koliber Strong family are characterized by large
capacity with optimized home and office dimensions. Safes Koliber Strong can be used as free-standing safes, after
fixing them to the ground.
Certificates for storing:
Valuables in acoordance with the EN 14450 standard, grade S1.
Warning! In order to keep the product’s resistance grade safe or cabinet weighing up to 1 000 kg must be anchored
to the ground (freestanding models) or built into the wall (built-in models) according to the user manual.
Styles of finishing:
Koliber Strong safes are covered with powder paint. The door has an ornamental signboard under the
handle and keyboard of the lock. Color light grey or black.

www.eurosafes.eu
Koliber Strong safes, grade S1
Product description:
The low mass allows installation in any room.
The powder paint finish makes it easy to integrate the safe into any interior of the office or the
apartment.
Body made of sheet # 3 mm; single-walled construction with high resistance to impact.
The front panel of the door is made of sheet # 5 mm.
Additional cover of bolt and lock system.
Internal hinges, door opening angle 900
Locking the door using movable bolts with a diameter of 20 mm.
Movable horizontal and vertical bolts
Additional protection of the lock against drilling.
Suitable for fixing to the ground.
Standard equipment:
Electronic lock M-Lock.
Shelf with adjustable suspension height (models with a height of 450 and 620 mm).
Shelf hooks (models with a height of 450 and 620 mm).
Mounting holes in the bottom.
Instructions for use of the product
Additional equipment:
Additional shelves (models with a height of 450 and 620 mm).
Mounting anchors
Left-side version
Output of the alarm system.
Shock detectors - they transmit an impulse to the alarm system when attempting to break in.
Bolt position sensor - transmits a pulse to the alarm system about the door opening status.
Additional mounting holes in the rear wall.
Standard colors:
RAL 7035 –light grey
RAL 9005 –black
Specifications:
Model
External dimentions [mm]
Internal dimensions [mm]
Weight
[kg]
Capacity
[l]
W
S
G
W
S
G
Koliber 20 Laptop 15” Strong
200
490
370
168
484
305
24
25
Koliber 26 Laptop 17” Strong
260
490
370
228
484
305
27
33
Koliber 45 Laptop 15” Strong
450
400
370
418
394
305
35
49
Koliber 45 Laptop 17” Strong
450
490
370
418
484
305
40
60
Koliber 62 Laptop 17” Strong
620
490
370
588
484
305
50
85
The weight of the products and their capacity is given for information purposes and may change

www.eurosafes.eu
Koliber Strong safes, grade S1
Operating the safe –opening
Opening of products equipped with only an electronic lock:
1. Open the lock by following the steps described in the enclosed lock manual.
2. Turn the handle clockwise
2. Pull the handle towards you, the product opens.
Maintenance:
Doors: It is recommended to lubricate the hinge as needed, but not less often than once every three years with
bearing grease, all joints and friction pairs of mechanisms should be lubricated with acid-free Vaseline once every
three years.
Body: In principle, the body does not require any special maintenance. The basic maintenance is cleaning the body
case. For this purpose, use a soft cloth moistened with a mild detergent and then wipe the cleaned surface dry.
Exploitation:
The use of products should take place in rooms protected against atmospheric agents, away from
corrosive substances on metals. Relative humidity in the room up to 75%. The device can work in rooms
where the temperature is between + 5oC and + 40oC.
When closing or opening the product, pay attention to movable elements, eg: drawer, door. Improperly
used may cause injury to the body, for example: fingers, if they are between the drawer and the body or
door and the body.
You should pay attention to the position of the bolts when closing the door, the bolts must be completely
hidden, otherwise you can permanently damage the mechanisms.
Mounted locks and mechanisms can not be processed under the threat of losing the guarantee.
If it is necessary to change the keys, it is recommended to replace the entire lock.
Attention should be paid to placing the safe in such a way that the door does not hit the obstacles
directly.
Locking mechanisms and locks should work smoothly and without jamming, when any objection arises, as
to the work of these components should be reported to the KONSMETAL service.
If any objections arise, as to the delivered product, please report them to the KONSMETAL website.