Konquest KDT-1201 Instruction manual

QUICK USER GUIDE
KONQUEST KDT-1201
ORAL - ARMPIT - RECTAL THERMOMETER
KDT-1201

[1] Power button
[2] LCD display screen
[3] Probe
[4] Battery cap
BATTERY REPLACEMENT
PRODUCT STRUCTURE
1
1
4
3
2
1. Replace battery when “ ”appears in the lower right
corner of LCD display.
2. Pull battery cover off as shown in Figure 1.
3. Gently pull out plastic circuit board with battery chamber
approximately 1 cm (slightly less than1/2".) Figure 2
4. Use pointed object such as a pen to remove old battery.
Discard battery lawfully. Replace with new 1.5V DC button
type LR41 or SR41,UCC392, or equivalent.
Be sure battery is installed with “+”polarity facing up. Figure 3
5. Slide battery chamber back into place and attach cover.
Figure 1 Figure 2 Figure 3

Figure 4
1DIRECTIONS
[1] Press the On/Off Button next to LCD display. A tone will sound as
the screen shows , followed by last recored temperature. After
showing the self-test temperature, the thermometer is now in the testing
mode.
*Note: If the measured temperature is less than 90˚F or 32˚C , the LCD
will display Lo, if the measured temperature is higher than 109.9˚For
42.9˚C, the LCD will display Hi.
[2] Position thermometer in desired location
(mouth, rectum, or armpit.)
a) Oral Use: Place thermometer under tongue
as indicated by “√” position shown in Figure 4.
Close your mouth and breathe evenly through the
nose to prevent the measurement from being
influenced by inhaled/exhaled air. Normal
temperature between 96.3˚F and 99.1˚F
(35.7 ˚C and 37.3 ˚C)
b) Rectal Use: Lubricate silver probe tip with petroleum jelly for easy
insertion. Gently insert sensor approximately 1cm (less than 1/2 ") into
rectum. Normal temperature between 97.2˚F and 99.9˚F (36.2 ˚C and
37.7 ˚C).
c) Armpit Use: Wipe armpit dry. Place probe in armpit and keep arm
pressed firmly at side. From a medical viewpoint, this method will always
provide inaccurate readings, and should not be used if precise measure-
ments are required. Normal temperature between 95.4˚F and
98.1˚F(35.2 ˚C and 36.7 ˚C).
2
M

1CLEANING AND DESINFECTION
READ INSTRUCTION MANUAL THOROUGHLY BEFORE USE
[3] The degree sign flashes throughout the testing process. When flashing
stops an alarm will beep for approximately 10 seconds. The measured read-
ing will appear on the LCD simultaneously. The minimum measurement time
until the signaling tone (beep) must be maintained without exception. The
measurement continues even after the buzzer notification. The displayed
temperature will not change when thermometer is removed from its testing
position.
[4] To prolong battery life, press the On/Off Button to turn unit off after
testing is complete. If no action is taken, the unit will automatically shut off
after around10 minutes.
[5] Store the thermometer in its protective case.
Wipe the thermometer with a soft clean cloth.
For stubborn stains, wipe the thermometer with a cloth that has been
dampened with water or a neutral detergent solution and then wring
thoroughly. Finish by wiping with a soft dry cloth.
For disinfection, 70% Ethanol or Isopropyl alcohol can be used.
Observe the following to prevent damage to the thermometer.
-Do not use benzene, thinner, gasoline or other strong solvents to clean the
thermometer.
-Do not attempt to disinfect the sensing section (tip) of the thermometer by
immersing in alcohol or in hot water (water over 122˚F (50˚C)).
-Do not use ultrasonic washing to clean the thermometer.
3