Kontron 886LCD-M/ATX User manual

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 1 of 78
User Manual
for the Mother Boards:
886LCD-M/Flex
886LCD-M/mITX
886LCD-M/ATX

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 2 of 78
Document revision history.
Revision Date By Comment
E May. 24th, 2005 PJA/MLA Major revision. BIOS information added.
D Dec. 20th, 2004 PJA 886LCD-M/ATX information added
C Dec. 13th, 2004 PJA 886LCD-M/mITX information added
A Sept. 27th, 2004 MLA Many correction and added information, but still preliminary
0.1 June 14th, 2004 PJA First preliminary manual version.
Copyright Notice:
Copyright ©2005, KONTRON Technology A/S, ALL RIGHTS RESERVED.
No part of this document may be reproduced or transmitted in any form or by any means, electronically or
mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
Trademark Acknowledgement:
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer:
KONTRON Technology A/S reserves the right to make changes, without notice, to any product, including
circuits and/or software described or contained in this manual in order to improve design and/or
performance.
Specifications listed in this manual are subject to change without notice. KONTRON Technology assumes
no responsibility or liability for the use of the described product(s), conveys no license or title under any
patent, copyright, or mask work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Applications that are described in this manual are for illustration purposes only. KONTRON Technology A/S
makes no representation or warranty that such application will be suitable for the specified use without
further testing or modification.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 3 of 78
Life Support Policy
KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL
MANAGER OF KONTRON Technology A/S.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in significant injury to
the user.
2. A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.
KONTRON Technology Technical Support and Services
If you have questions about installing or using your KONTRON Technology Product, check this User’s
Manual first – you will find answers to most questions here. To obtain support, please contact your local
Distributor or Field Application Engineer (FAE).
Before Contacting Support: Please be prepared to provide as much information as possible:
CPU Board
1. Type.
2. Part-number (Number starting with “53”).
3. Serial Number.
Configuration
1. CPU Type, Clock speed.
2. DRAM Type and Size.
3. BIOS Revision (Find the Version Info in the BIOS Setup in the Kontron Section).
4. BIOS Settings different than Default Settings (Refer to the Software Manual).
System
1. O/S Make and Version.
2. Driver Version numbers (Graphics, Network, and Audio).
3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 4 of 78
Table of contents:
1. INTRODUCTION.....................................................................................................................................7
2. INSTALLATION PROCEDURE..............................................................................................................8
2.1 Installing the board............................................................................................................................8
2.2 Requirement according to EN60950................................................................................................9
3. SYSTEM SPECIFICATION...................................................................................................................10
3.1 Component main data .....................................................................................................................10
3.2 Processor support table..................................................................................................................13
3.3 System Memory support.................................................................................................................13
3.4 System overview..............................................................................................................................14
3.5 886LCD-M Power Distribution & Power State Map ......................................................................15
3.6 Power Consumption........................................................................................................................17
3.6.1 Test system configuration...........................................................................................................17
3.6.2 Measured Power Consumption, Net...........................................................................................17
3.6.3 Power Consumption, Total .........................................................................................................18
3.6.4 Minimum recommended power supply specifications................................................................18
3.6.5 Recommended Power Supply specifications .............................................................................18
3.7 886LCD-M Clock Distribution .........................................................................................................19
4. CONNECTOR DEFINITIONS................................................................................................................21
4.1 Connector layout..............................................................................................................................22
4.1.1 886LCD-M/Flex...........................................................................................................................22
4.1.2 886LCD-M/ATX ..........................................................................................................................23
4.1.3 886LCD-M/mITX.........................................................................................................................24
4.2 Power Connector (ATXPWR)..........................................................................................................24
4.2 Power Connector (ATXPWR)..........................................................................................................25
4.3 Keyboard and PS/2 mouse connectors.........................................................................................26
4.3.1 Stacked MINI-DIN keyboard and mouse Connector (MSE & KBD)...........................................26
4.3.2 keyboard and mouse pin-row Connector (KBDMSE).................................................................26
4.4 Display Connectors .........................................................................................................................27
4.4.1 CRT Connector (CRT)................................................................................................................27
4.4.2 LVDS Flat Panel Connector (LVDS)...........................................................................................28
4.4.3 AGP/DVO connector...................................................................................................................29
4.5 Parallel ATA harddisk interface......................................................................................................33
4.5.1 IDE Hard Disk Connector (IDE_P) .............................................................................................34
4.5.2 IDE Hard Disk Connector (IDE_S) .............................................................................................34
4.5.3 IDE Hard Disk Connector (IDE_S2) ...........................................................................................35
4.5.4 CF Connector (CF).....................................................................................................................36
4.6 Serial ATA harddisk interface.........................................................................................................37
4.6.1 SATA Hard Disk Connector (SATA0, SATA1) ...........................................................................37

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 5 of 78
4.7 Printer Port Connector (PRINTER).................................................................................................38
4.8 Serial Ports .......................................................................................................................................39
4.8.1 Serial Port ComA DB9 Connector..............................................................................................39
4.8.2 Serial Port ComB, ComC & ComD Pin Header Connectors......................................................39
4.9 Ethernet connectors........................................................................................................................40
4.9.1 Ethernet connector 1 (ETHER1).................................................................................................40
4.9.2 Ethernet connector 2/3 (ETHER2/3)...........................................................................................41
4.10 USB Connector (USB)..................................................................................................................42
4.10.1 USB Connector 0/2 (USB0/2).....................................................................................................42
4.11 Audio Connector ..........................................................................................................................43
4.11.1 Audio Line-in, Line-out and Microphone.....................................................................................43
4.11.2 CD-ROM Audio input (CDROM).................................................................................................43
4.11.3 AUDIO Header (AUDIO_HEAD).................................................................................................44
4.12 Fan connectors , FAN_PROC and FAN_SYS. ...........................................................................45
4.13 The Clear CMOS Jumper, Clr-CMOS..........................................................................................45
4.14 LPC connector (unsupported). ...................................................................................................45
4.15 Front Panel connector (FRONTPNL)..........................................................................................46
4.16 Intruder Connector (INT)..............................................................................................................46
4.17 Feature Connector (FEATURE)...................................................................................................47
4.17.1 PCI Slot Connector....................................................................................................................48
4.17.2 Signal Description –PCI Slot Connector.....................................................................................49
4.17.3 886LCD-M PCI IRQ & INT routing..............................................................................................50
5. ONBOARD CONNECTORS .................................................................................................................51
6. SYSTEM RESSOURCES......................................................................................................................52
6.1 Memory map.....................................................................................................................................52
6.2 PCI devices.......................................................................................................................................52
6.3 Interrupt Usage ................................................................................................................................53
6.4 I/O Map ..............................................................................................................................................54
6.5 DMA Channel Usage........................................................................................................................54
7. OVERVIEW OF BIOS FEATURES.......................................................................................................55
7.1.1 System Management BIOS (SMBIOS / DMI).............................................................................55
7.1.2 Legacy USB Support..................................................................................................................55
8. BIOS CONFIGURATION / SETUP .......................................................................................................56
8.1 Introduction......................................................................................................................................56
8.2 Main Menu.........................................................................................................................................56
8.3 Advanced Menu................................................................................................................................57
8.3.1 Advanced settings – CPU Configuration....................................................................................57
8.3.2 Advanced settings – IDE Configuration......................................................................................58

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 6 of 78
8.3.3 Advanced settings – LAN Configuration.....................................................................................60
8.3.4 Advanced settings – Floppy Configuration.................................................................................61
8.3.5 Advanced settings – SuperIO Configuration ..............................................................................62
8.3.6 Advanced settings – Hardware Health Configuration ................................................................63
8.3.7 Advanced settings – ACPI Configuration ...................................................................................64
8.3.8 Advanced settings – General ACPI Configuration .....................................................................64
8.3.9 Advanced settings – Advanced ACPI Configuration..................................................................65
8.3.10 Advanced settings – Remote Access Configuration ..................................................................65
8.3.11 Advanced settings – USB Configuration ....................................................................................66
8.3.12 Advanced settings – USB Mass Storage Device Configuration.................................................67
8.4 PCIPnP Menu....................................................................................................................................68
8.5 Boot Menu.........................................................................................................................................69
8.5.1 Boot – Boot Settings Configuration ............................................................................................69
8.6 Security Menu...................................................................................................................................70
8.7 Chipset Menu....................................................................................................................................71
8.7.1 Advanced Chipset Settings – Intel Montara-GML NorthBridge Configuration...........................72
8.7.2 Advanced Chipset Settings – SouthBridge Configuration..........................................................73
8.8 Power Menu......................................................................................................................................74
8.9 Exit Menu..........................................................................................................................................75
8.10 AMI BIOS Beep Codes .................................................................................................................76
9. OS SETUP.............................................................................................................................................77
10. WARRANTY..........................................................................................................................................78

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 7 of 78
1. Introduction
This manual describes the 886LCD-M/Flex, 886LCD-M/ATX and 886LCD-M/mITX boards made by
KONTRON Technology A/S. The boards will also be denoted 886LCD family if no differentiation is required.
All boards are to be used with the Intel® Pentium® M & Intel Celeron® M Processors.
Use of this manual implies a basic knowledge of PC-AT hard- and software. This manual is focused on
describing the 886 Board’s special features and is not intended to be a standard PC-AT textbook.
New users are recommended to study the short installation procedure stated in chapter 3 before switching-
on the power.
All configuration and setup of the CPU board is either done automatically or by the user in the CMOS setup
menus. Except for the CMOS Clear jumper, no jumper configuration is required.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 8 of 78
!
!
2. Installation procedure
2.1 Installing the board
To get the board running, follow these steps. In some cases the board shipped from KONTRON Technology
has CPU, DDR DRAM and Cooler mounted. In this case Step 2-4 can be skipped.
1. Turn off the power supply.
2. Insert the DIMM DDR 184pin DRAM module(s). Be careful to push it in the slot(s) before locking the
tabs. For a list of approved DDR DRAM modules contact your Distributor or FAE (list under preparation).
DDR333, DIMM 184pin DRAM modules are supported.
3. Install the processor. The CPU is keyed and will only mount in the CPU socket in one way. Use the
handle to open/ close the CPU socket. Intel Pentium M and Celeron M processors (Banias processors)
are supported.
4. Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the
FAN_PROC connector.
5. Insert all external cables for hard disk, keyboard etc. except for flat panel. A CRT monitor must be
connected in order to change CMOS settings to flat panel support. To achieve UDMA-66/100/133
performance on the IDE interface, 80poled UDMA cables must be used. If using the IDE_S2 connector
care should be taken in correct orientation when attaching the female cable. The cables that KONTRON
provide do not have a key. There is possibility of damage to the HDD or PCB if the cable is not orientated
correctly.
6. Connect power supply to the board by the ATXPWR connector.
7. Turn on the power on the ATX power supply.
8. The PWRBTN_IN must be toggled to start the Power supply; this is done by shorting pins 16
(PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector description). A “normally
open” switch can be connected via the FRONTPNL connector.
9. Enter the BIOS setup by pressing the “F2” key during boot up. Refer to the Software Manual (under
preparation) for details on BIOS setup.
Enter Advanced Menu / CPU Configuration / Intel SpeedStep Tech. and set this option to “Maximum
Performance”.
Note: To clear all CMOS settings, including Password protection, move the CMOS_CLR jumper (with or without
power) for approximately 1 minute. Alternatively turn off power and remove the battery for 1 minute, but be
careful to orientate the battery corretly when reinserted.
Note: If the Audio Amplifiers shall be used to generate up to 3W on one or more of the
Audio ouput channels, then make sure that sufficent airflow is around the Audio
Amplifier. The Amplifier has integrated Thermal Protection and will not be damaged
even though the airflow is insufficient for normal operation.
Warning: Do not use Power Supply without 3.3V monitoring watchdog, which is
standard feature in ATX Power Supplies.
Running the board without 3.3V connected will damage the board after a few minutes.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 9 of 78
2.2 Requirement according to EN60950
Users of 886LCD boards should take care when designing chassis interface connectors in order to fulfill the
EN60950 standard:
Lithium Battery precautions:
CAUTION!
Danger of explosion if battery is incorrectly
replaced.
Replace only with same or equivalent type
recommended by manufacturer.
Dispose of used batteries according
to the manufacturer’s instructions.
VORSICHT!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch den selben oder einen vom
Hersteller empfohlenen gleichwertigen Typ.
Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
ADVARSEL!
Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende
type anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laltevalmistajan
suosittelemaan
tyyppiln. Hävitä käytetty paristo valmistajan
ohjeiden
mukaisesti.
When an interface/connector has a VCC (or other power) pin, which is directly connected to a power
plane like the VCC plane:
To protect the external power lines of peripheral devices the customer has to take care about:
•That the wires have the right diameter to withstand the maximum available power.
•That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC/EN 60950.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 10 of 78
3. System specification
3.1 Component main data
The table below summarises the features of the 886LCD-M/Flex, 886LCD-M/ATX and 886LCD-M/mITX
embedded motherboards.
Form factor 886LCD-M/Flex: Flex-ATX (190,50millimeters by 228,60millimeters)
886LCD-M/ATX: ATX (190,50millimeters by 304,00millimeters)
886LCD-M/mITX: mini ITX (170.18millimeters by 170.18millimeters)
Processor •Support for Intel Pentium M and Celeron M Processors in mPGA478 socket with
400MHz system bus.
•Banias (0.13um) and Dothan (0.09um) family processors.
Memory •For /Flex and /ATX: 2x184pin DDR SDRAM Dual Inline Memory Module (DIMM)
sockets.
•For /mITX: 1x184pin DDR SDRAM Dual Inline Memory Module (DIMM) sockets.
•Support for DDR 266/333 (PC2100/PC2700)
•Support for up to 2GB of system memory (/Flex and /ATX)
•Support for up to 1GB of system memory (/mITX)
•ECC support depend on Intel
Chipset Intel 855GME Chipset consisting of:
•Intel® 855GME Chipset Graphics and Memory Controller Hub (GMCH)
•Intel® 6300ESB I/O Controller Hub (ICH)
•4 Mbit Firmware Hub (FWH)
Video •Intel Extreme Graphics 2 controller
•Analog Display Support, 350-MHz integrated 24-bit RAMDAC with support for
analogue monitors up to 2048x1536 at 75 Hz
•Digital Video Out Port (DVOB & DVOC) support, dot clock up to 165-MHz
DVI DVO ADD and CRT DVO ADD supported.
LVDS DVO ADD cards currently not supported
•Single or dual channel LVDS panel support (18/ 24bit OpenLDI / SPWG) up to
UXGA panel resolution
•Dual independent pipe support, Mirror and Dual independent display support
Tri-view support through LVDS interface, DVO B/C port, and CRT
CRT – LVDS supported
CRT - DVO/ Add card supported
LVDS - DVO/ Add card supported
•AGP 2.0, 1.5V connector (DVO B/C muxed w/ AGP) supporting 1x, 2x, and 4x
AGP cards or an AGP Digital Display (ADD) card
Audio Audio, AC97 version 2.3 subsystem using the Realtek ALC655 codec
•Audio Amplifier
o/FLEX and /ATX: 4x3W
o/mITX: 2x3W
•Line-out
•CDROM in
•SPDIF Interface (Surround)
•Microphone
Onboard speaker
I/O Control Winbond W83627THF LPC Bus I/O Controller
Peripheral
interfaces •Four USB 2.0 ports
•Four Serial ports (RS232). Note: Intel 6300ESB Serial port FIFO (COM C+D) is
not standard compliant. May cause issues with specific SW.
•One Parallel port, SPP/EPP/ECP / Floppy (optional floppy with special cabling)
•Two Serial ATA 150 IDE interfaces, ATA Mode 6 not supported due to Intel
Chipset restrictions.
•Two Parallel ATA IDE interfaces with UDMA 33, ATA-66/100 support
•PS/2 keyboard and mouse ports
(continued)

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 11 of 78
LAN Support 3x 10/100/1000Mbits/s LAN subsystem using the Realtek RTL8110SB-32 LAN
controllers or
1x / 3x 10/100Mbits/s LAN subsystem using the Realtek RTL8100C LAN controllers
depending on board configuration.
PXE and RPL netboot supported. Wake On LAN (WOL) supported.
BIOS •Kontron Technology / AMI BIOS (core version)
•Support for Advanced Configuration and Power Interface (ACPI 1.0, 2.0), Plug
and Play
oSuspend To Ram
oSuspend To Disk
oIntel Speed Step
•SW Watchdog currently not supported by BIOS
•Secure CMOS/ OEM Setup Defaults
•“Always On” BIOS power setting
•RAID Support (RAID modes 0 and 1)
Instantly
Available PC
Technology
•Support for PCI Local Bus Specification Revision 2.2
•Suspend to RAM support
Expansion
Capabilities •SMBus routed to FEATURE connector
•LPC Bus routed to LPC connector
•DDC Bus routed to LVDS connector
•8 x GPIOs (General Purpose I/Os) routed to FEATURE connector
•PCI Bus routed to PCI slot(s) (PCI Local Bus Specification Revision 2.2)
Hardware
Monitor
Subsystem
•Smart Fan control system, support Thermal® and Speed® cruise for three
onboard Fan control connectors: FAN_PROC, FAN_SYS and FEATURE
•Three thermal inputs: CPU die temperature, System temperature and External
temperature input routed to FEATURE connector.
•Voltage monitoring
•Intrusion detect input
SMI violations (BIOS) on HW monitor not supported. Supported by API (Windows).
Operating
Systems
Support
•Win2000
•WinXP
•Win98 (USB2.0, ACPI S4 not supported)
•Win2003
•WinXP Embedded (limitations may apply)
•WinCE.net (limitations may apply)
•Linux: Feodora Core 3, Suse 9.2 (limitations may apply)
(continued)

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 12 of 78
Environmental
Conditions Operating:
0°C – 60°C operating temperature (forced cooling). It is the customer’s responsibility
to provide sufficient airflow around each of the components to keep them within
allowed temperature range.
10% - 90% relative humidity (non-condensing)
Storage:
-20°C – 70°C
5% - 95% relative humidity (non-condensing)
Electro Static Discharge (ESD) / Radiated Emissions (EMI):
All Peripheral interfaces intended for connection to external equipment are ESD/ EMI
protected.
EN 61000-4-2:2000 ESD Immunity
EN55022:1998 class B Generic Emission Standard.
Safety:
UL 60950-1:2003, First Edition
CSA C22.2 No. 60950-1-03 1st Ed. April 1, 2003
Product Category: Information Technology Equipment Including Electrical Business
Equipment
Product Category CCN: NWGQ2, NWGQ8
File number: E194252
Theoretical MTBF:
199,799hours (22,8years) , Calculation based on Telcordia SR-332 method.
Restriction of Hazardeous Substances (RoHS):
All boards in the 886LCD-M family is planned for RoHS compliance.
Capacitor utilization:
No Tantal capacitors on board
Only Japanese brand Aluminium capacitors rated for 100degrees Celsius used on
board
Battery Exchangeable 3.0V Lithium battery for onboard Real Time Clock and CMOS RAM.
Manufacturer Toshiba / Part-number CR2032.
Approximate 5 years retention.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 13 of 78
3.2 Processor support table.
886LCD-M/Flex, 886LCD-M/ATX and 886LCD-M/mITX boards are designed to support the following
processors:
Intel® Pentium® M Processor, 130 nm process with 1 MB L2 cache
Intel® Pentium® M Processor, 90 nm process with 2 MB L2 cache
Intel®Celeron® M Processor, 130 nm process with 512 kB L2 cache
Intel®Celeron® M Processor, 90 nm process with 1 MB L2 cache
Processor Brand Processor
Number Processor Generation Clock Speed Front Side Bus Cache
Intel® Pentium® M 765 Dothan 90nm 2.1 GHz 400 MHz 2MB L2
755 Dothan 90nm 2.0 GHz 400 MHz 2MB L2
745 Dothan 90nm 1.8 GHz 400 MHz 2MB L2
735 Dothan 90nm 1.7 GHz 400 MHz 2MB L2
725 Dothan 90nm 1.6 GHz 400 MHz 2MB L2
RH80535GC0251M Banias 130nm 1.6 GHz 400 MHz 1MB L2
715 Dothan 90nm 1.5 GHz 400 MHz 2MB L2
705 Dothan 130nm 1.5 GHz 400 MHz 1MB L2
Intel® Celeron® M 370 Dothan 90nm 1.5 GHz 400 MHz 1MB L2
360 Dothan 90nm 1.4 GHz 400 MHz 1MB L2
350 Dothan 90nm 1.3 GHz 400 MHz 1MB L2
340 Banias 130nm 1.5 GHz 400 MHz 512MB L2
330 Banias 130nm 1.4 GHz 400 MHz 512MB L2
320 Banias 130nm 1.3 GHz 400 MHz 512KB L2
The above list contains PGA versions only, but also BGA versions are supported, if required please ask
Kontron for more information.
3.3 System Memory support
The 886LCD-M/Flex and 886LCD-M/ATX boards have two onboard DIMM sockets (886LCD-M/mITX
equipped with one DIMM socket only) and support the following memory features:
•2.5V (only) 184-pin DDR SDRAM DIMMs with gold-plated contacts
•Supports up to two (one on mITX) single-sided and/or double-sided DIMMs (four rows populated)
with unbuffered PC1600/PC2100/PC2700 DDR-SDRAM (with or without ECC(depends on Intel))
•Supports 64 Mbit, 128 Mbit, 256 Mbit and 512 Mbit technologies for x8 and x16 width devices.
•Maximum of 2 Gbytes system (1GB on mITX) memory by using 512 Mbit technology devices
(double sided)
•Supports 200 MHz, 266 MHz, and 333 MHz DDR devices
•64-bit data interface (72-bit with ECC(depends on Intel))
The installed DDR SDRAM should support the Serial Presence Detect (SPD) data structure. This allows the
BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the
BIOS will attempt to configure the memory settings, but performance and reliability may be impacted.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 14 of 78
Intel
Processor M
Banias
&Dothan
Intel
855GME
Intel
ICH(S)
HPI HUB link 1.5
LVDS
24bit
DVO/
AGP
VGA
1x184 pins
DDR333
ECCsuport
SIO
Winbond
W83267
THF
4Mbit
LPC
FLASH
LPC LPC
PCI
2.2
32bit
33
MHz
#1
PCI
2.2
32bit
33
MHz
#2
PCI
2.2
32bit
33
MHz
#3
PCI 2.2 32bit, 33MHz
10/100/
1GbE
PCI-X32bit, 66MHz
10/100/
1GbE
10/100/
1GbE
AC97
RTL655
3W
amplifier 3W amplifier
LPF,Center
orFrontL+R
Rear L+R
COM
#1
COM
#2
Header
COM
#4
Header
COM
#3
Header
2x
ATA100
2x
SATA150
2x
Internal
USB 2x
External
USB
AC97
KBD MSELPT
1x184 pins
DDR333
ECCsuport
PCI
2.2
32bit
33
MHz
#4
PCI
2.2
32bit
33
MHz
#5
PCI
2.2
32bit
33
MHz
#6
3.4 System overview
The block diagram below shows the architecture and main components of the 886LCD boards. The two key
components on the board are the Intel®855GME and Intel®6300ESB (ICH(S)) Embedded Chipsets.
Components shown shaded are optional depending on board type (886LCD-M/Flex, /ATX or /mITX) and
variants of the board.

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 15 of 78
LDO Regulator
Ref. U1SS
ATX PSU
Ref.: ATXPWR
+V5_ALWAYS +V5S +V3.3S VCC12 VCC-12
+V3.3ALWAYS LDO Regulator
Ref. U2SS
+V1.5ALWAYS
LDO Regulator
Ref. U3SS
+V1.8S
DC/DC
regulator
Ref.:
COREREG
+VCC_CORE
DC/DC
regulator
Ref.:
VCCPREG
+V1.2S
+V1.5S
LDO regulator
Ref.:
VCCPAMP
+VCCP
DC/DC
regulator
Ref.:
ACPICTRL
+V2.5
+V1.25S
MOSFET
SWITCH
Ref.: 1SD, 7SD
+V5_DUAL
MOSFET
SWITCH
Ref.: 1SD, 7SD
+V3.3_DUAL
VCC-12
VCC12
Battery or
+V3.3_ALWAY
S
Ref.:
BT1II
+V_RTC
3.5 886LCD-M Power Distribution & Power State Map
(continued)

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 16 of 78
Processor
Ref.:
BANIAS_
USB
connectors
Ref.:
USB_ETH,
FRONTPNL
Audio
Amplifiers
Ref.:
U1A1, U1A2
DDR Memory
Ref.:
DDRX
Ethernet
Controllers
Ref.:
ETH1
COM drivers
Ref.:
COMXDRV
LPT port
Ref.:
CRT_COMA_L
PT_
BIOS Flash
Ref.:
FWH
KBD / MSE
Ref.:
KBD_MSE
+VCC_CORE
+VCCP
+VCCP
+V1.8S
+V1.2S
+V1.5S
+V2.5
AC97 Codec
Ref.:
Codec
North Bridge
Ref.:
GMCH_
+V3.3S
+V3.3S
+V1.5S
+VCCP
+V_RTC
+V5_ALWAYS
South Bridge
Ref.:
ICHS_
+V3.3_ALWAYS
+V3.3_DUAL
+V5S
+V1.5_ALWAYS
+V2.5
+V1.25S
+V3.3S
+V3.3S
+V5S
VCC12
+V1.5S
AGP
Ref.:
AGP
+V3.3_ALWAYS
PCI slots
Ref.:
PCIX
+V5S
VCC12
VCC-12
+V3.3S
+V3.3_ALWAYS
+V3.3_DUAL
Ethernet
Controllers
Ref.:
ETH2, ETH3
+V3.3S
+V5S
+V5S
VCC12
VCC-12
+V5_DUAL
+V5_DUAL+V3.3S
VCC12
+V3.3S
S0 S3 S5
+V5S
+V3.3S
VCC12
VCC-12
+V_RTC
+V1.8S
+VCC_CORE
+V1.2S
+V1.5S
+VCCP
+V2.5
+V1.25S
+V5_DUAL
+V3.3_DUAL
+V5_ALWAYS
+V3.3ALWAYS
+V1.5ALWAYS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
X
N/A
X
X
X
X
X
X
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
X

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 17 of 78
3.6 Power Consumption
This section lists a summary of the power consumption of the 886LCD-M Boards. For additional details,
please refer to the Power Supply Characteristics document available from Kontron Technology.
The idle/full power consumption of the 886LCD-M is measured under:
1- DOS prompt idle/full CPU load.
2- WindowsXP idle/full CPU load.
3.6.1 Test system configuration
The following items were used in the test setup:
1. 886LCD-M/Flex board (710180-4500), mounted with 256MB SDRAM (333MHz) EZ128DDR16M168-
333INF.
2. Pentium-M 1600/600Mhz, FSB 400Mhz (1MB Cache) CPU.
3. Standard Pentium-4 active CPU cooler.
4. PS/2 keyboard & mouse.
5. CRT.
6. Primary Master HD (Fujitsu MPG3102AT 10.24GB).
7. ATX PSU (Antec 550W)
8. Tektronix TDS 620B, P6243 probes
9. Fluke Current Probe 80i-100S AC/DC
10. Ethernet Ports 1, 2, 3 are enabled (10/100/1000MB LAN).
3.6.2 Measured Power Consumption, Net
886LCD-M board (3x1GB LAN) with: Pentium M 1600/400MHz (1MB L2 Cache), 256MB DDR RAM
(333MHz)
Power State Net Current (I) Power (W)
DOS FULL LOAD +5VDC 4.560A 22.8W
+3.3VDC 2.568A 8.7W
DOS IDLE +5VDC 4.028A 20.3W
+3.3VDC 2.532A 8.6W
+12VDC 0.424A 4.6W
ACPI S1 +5VDC 1.758A 8.8W
+3.3VDC 2.560A 8.8W
ACPI S3 +5VSB 1.007A 5.16W
ACPI S4 +5VSB 1.007A 4.95W
ACPI S5 +5VSB 0.892A 4.6W
WINDOWS XP IDLE +5VDC 2.212A 11.1W
+3.3VDC 2.720A 8.7W
WINDOWS XP FULL LOAD +5VDC 4.704A 23.7W
+3.3VDC 2.572A 8.7W

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 18 of 78
3.6.3 Power Consumption, Total
886LCD-M board (3x1GB LAN) with Pentium M 1600/400MHz (1MB L2 Cache), 256MB DDR RAM
(333MHz)
Power State CPU Speed Power consumption
Full load 1600Mhz 37.0W
Idle 1600Mhz 24.4W
ACPI S1 1600Mhz 22.2W
ACPI S3 1600Mhz 5.16W
ACPI S4 1600Mhz 4.95W
ACPI S5 1600Mhz 4.60W
886LCD-M board (3x1GB LAN) with Intel Mobile Celeron 600/400MHz (0MB L2 Cache) BGA, 256MB DDR
RAM (333MHz)
Power State CPU Speed Power consumption
Full load 600Mhz 28.4W
Idle 600Mhz 22.8W
ACPI S1 600Mhz 21.6W
ACPI S3 600Mhz 5.16W
ACPI S4 600Mhz 4.95W
ACPI S5 600Mhz 4.60W
3.6.4 Minimum recommended power supply specifications
Note: Minimum recommended power supply specifications do not include attachment of AUDIO Speakers
(AMP-out), USB, AGP, PCI devices. If these devices are added to the board, additional power requirements
must be taken into account. Refer to the “Detailed Device Power consumption” section.
Net Current (I) Peak Current
+5VDC 8.0A 40.0A(3ms)
+3.3VDC 4.0A 14.0A(3ms)
+12VDC 0.6A 6.0A(4ms)
+5VSB 1.2A 3.5A(14ms)
-12 VDC 0.2A 1.0A(4ms)
-5VDC N/A N/A
3.6.5 Recommended Power Supply specifications
Note: Recommended power supply specifications, includes attachment of COM, Fan, 4xAudio Speakers
4/8ohm, USB, AGP, PCI devices.
Net Current (I) Peak Current
+5VDC 18.0A 50.0A(3ms)
+3.3VDC 7.0A 20.0A(3ms)
+12VDC 6.0A 8.0A(4ms)
+5VSB 2.0A 5.0A(14ms)
-12 VDC 0.5A 1.0A(4ms)
-5VDC N/A N/A

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 19 of 78
14.318 MHz
Ref.: Q1C
VR_PWRGD_CK#
Processor
Ref.: Banias_
CLK_CPU_BCLK & CLK_CPU_BCLK#
CLK_ITP_CPU &CLK_ITP_CPU#
CLK_MCH_BCLK & CLK_MCH_BCLK#
HOST CLOCK PAIRS
100MHz
100MHz
100MHz
ClockGenerator
Ref.:CLKGEN
SATACLOCKPAIR
100MHz CLK100P_SATA & CLK100P_SATA#
AGP,GMCH,ICHS,PCIX
NorthBridge
Ref.: GMCH_
South Bridge
Ref.: ICHS_
66MHz
66MHz
66MHz
66MHz CLK_3V66_PCIX
AGP
Ref.: AGP
CK_66M_AGP
CLK_MCH66
CLK_ICHPCI
CLK_PCI_SLX
PCI, LPC, FWH, SIO
33MHz
33MHz
33MHz
33MHz PCI Slots
Ref.: PCIX
BIOSFLASH
Ref.: FWH
Super I/O
Ref.: LPCIO
CLK_ICHPCI
CLK_FWHPCI
CLK_SIOPCI
48MHz
DREFCLK
48MCLK
48MHz
Clockbuffer
Ref.:
CLKGEN48M
CLK_ICH14
14.318MHz
14.318MHz
AC97
CODEC
Ref.: Codec
CLK_CODEC
DREFSSCLK
66MHz
3.7 886LCD-M Clock Distribution
(continued)

886LCD-M Family
KTD-00474-E Public User Manual Date: 2005-05-24 Page 20 of 78
North Bridge
Ref.: GMCH_
South Bridge
Ref.: ICHS_
Super I/O
Ref.: LPCIO
Clock buffer
Ref.:
CLKGEN48M
CLK_SIO48
CLK_ICH48S
CLK_ICH48
AC97
CODEC
Ref.: Codec
M_CLK_DDRX & M_CLK_DDRX#
DDR Memory
Ref.: DDR0,
DDR1
LVDS
Interface
Ref.: LVDS
LVDS_CLKX & LVDS_CLKX#
LVDS_DDCPCLK
DAC_DDCACLK
CRT VGA
Ref.:
CRT_COMA
_LPT_
AC97_BITCLK
KBCLK#
MSCLK#
MSE/KBD
Ref.:
KBD_MSE
Real Time
Clock
32.768
Ref.: Q1II
ETHERNET
controllers
Ref.: ETH#
PXPCLKO#
25 MHz
Ref.: Y1EX