Koopers Bolero User manual

Group 0+,I, (0-18KG)
Bolero (Isox only)
Koopers Distribution Sdn Bhd
03-78324338
www.koopers.co
www.facebook.com/koopersdistribution
[email protected]
18-1,Jalan Bulan U5/BM, Section U5, Bandar Pinggiran Subang,
40150 Shah Alam, Selangor
Malaysia

2
4
6
6
6
7
8
8
9
10
10
11
12
12
13
13
15
15
16
1 2
Contens
1. Important Notice...........................................................................................................
2. Features........................................................................................................................
3. Attention for car seat usage.......................................................................................
4. The adjustment and usage of the child car seat.......................................................
4-1 Recline position adjustment........................................................................................
4-2 Harness adjustment....................................................................................................
4-3 Headrest adjustment...................................................................................................
4-4 Buckle adjustment.......................................................................................................
4-5 ISOFIX installation and removal.................................................................................
4-6 Support leg installation and adjustment.......................................................................
4-7 Usage of infant insert...................................................................................................
4-8 Removing and Refitting the cover...............................................................................
5. Installation.....................................................................................................................
5-1 Rearward facing..........................................................................................................
5-2 Forward facing.............................................................................................................
5-3 Change groups............................................................................................................
6. Side facing installation...............................................................................................
7. Cleaning and maintenance..........................................................................................
8. Notice.............................................................................................................................
User instructions
We are pleased that our “Bolero” car seat will accompany your child safely throughout
their childhod life .
In order to protect your child, the Bolero must always be used and installed according to
the instructions.
If you have any futher query regarding its usage, please contact us.
1. Important Notice:
1. This child seat is suitable for child weighs less than 18kg.
2. Please get the operation manual from the net bag, which is located inside the back
cover of the child seat, and read carefully.
3. Please read carefully before installation, serious injury will occur if installed incorrectly.
Manufacturer won't take any responsibility for any risks in this case.
4.Never use the child seat without a cover.Never use any cover which is not
recommended by manufacturer to replace the old cover, it is because the cover
constitutes an integral part of the child car seat performance.
5. When the child seat is not provided with a textile cover, the seat should be kept away
from sunlight, otherwise it may be too hot for child's skin.
6. Never place the child seat on the vehicle seat with an active airbag.
7. The child seat should be disposed when it has been subjected to violent stress in an
accident.
8. Please ensure all passengers in the car use the safety belts, goods in car must be
properly secured, otherwise the passengers and goods may injure the child during an
emergency brake situation.
9. Buckle cannot be left in semi-locked status. Always ensure that the buckle is locked
properly.
10. Don't make any changes or add any additions on the harness system in the child seat,
otherwise it could seriously affect the safety and functionality.
11. The child should not be left on the child seat if he/she is not accompanied by an adult.
12. Keep the child seat away from the corrosive.
13. Always keep the child seat secured in the vehicle even when it is unoccupied, children
should not be left in their child car seat unattended.
14. Manufacturer quarantee the quality, excluded second-hand child seat.
15. Please ensure that the lap strap is worn low down,so that the child’s pelvis is firmly
engaged on the seat.
16. All straps holding the child seat to the vehicle should be tight, the straps restraining the
child should be adjusted to suit the child's body and the straps should not be twisted.

2. Features
3 4
Product Description
9KG-18KG
0-13KG
Group Installation Methods Approval type The scope of
application
0+
I
ISOFIX
ISOFIX Semi-Universal
Semi-Universal
17. If you have any question about the usage and installation of the child seat, please
contact our service hotline.
18. Do not use any weight bearing points other than those described in the instructions
and marked in the child restraint.
19.Do not use forward-facing position when child weighs less than 9kg.
20.The instructions can be retained on the child seat for it’s life period and please take
good care of the manual.
21.The rigid items and plastic parts of a child seat must be located and installed properly,
make sure they are not trapped by a movable seat or a door of the vehicle during
everyday usage.
1
14
2
3
15
16
4
11
12
13
9
10
8
5
6
7
27

4-1 Recline position adjustment
Change the recline positions by turning the recline knob
8.
If you would like to turn to recline position 4 (the lowest
reclined position), please press the second lock button
10 while turning the recline knob 8.
5 6
Danger! DO NOT use on a passenger seat with an
active airbag. If hit by the airbag, death or serious
injures may occur.
In order to properly protect your child, please read the
instructions carefully.
DO NOT use on a passenger seat with an
active airbag.
PARTNO. PART PART PARTNO. NO. NO.
1
5
9
13
17
21
25
2
6
10
14
18
22
26
3
7
11
15
19
23
4
8
12
16
20
24
Headrest shoulder pad infant insert
recline knob
adjustment button
ISOFIX
instruction cabin
cover button
support leg
adjustment button
buckle pad
support leg
harness yoke
ISOFIX
adjustment strap
adjustment strap
harness buckle
second lock button
rotation handle
shoulder pad strap
rebound board
ISOFIX
insert guider
headrest
adjustment handle
shoulder straps
car seat base
instruction
cabin cover
ISOFIX
release button
support leg
indicator
connector of
shoulder pad
3. The attention for car using
4. The adjustment and usage of the child car seat
Caution:
1. When the child’s weight is less 13kg (group 0+), only
the recline position 4 is suitable for rearward facing.
2. When the child’s weight is 9-18kg (group I), only the
recline position blue 1,2,3 are suitable for rearward
facing.
3. When the child ‘s weight is 9-18kg (group I), only the
recline position red 1,2,3 are suitable for forward facing.
Rearward facing
9-18kg Y
Rearward facing
0-13kg Y
Forward facing
9-18kg Y
Pressed safety button for
the most reclined position
1234
2
3
17 18
19
20
21
22
23
26
24
25
27 ISOFIX
second lock button
10
8

4-2 Harness adjustment 4-3 Headrest adjustment
4-4 Buckle adjustment
D
2
6
1
F
7 8
Caution: Adjusting button 16 with
its operation function, please
operate correctly according to the
picture.
Loosen: press adjusting button 16 and
at same time pull both shoulder strap 5
forwards (Do not pull on the shoulder
pads 3).
Pull up: Pull the adjusting handle 2of the
headrest upwards.
Push down: Push the adjusting handle 2 of the
headrest downward.
Tighten: Pull the adjustment strap 15 until the harness lies
flat and close against your child's body.
Caution:
Grasp the both shoulder straps 5by one hand (with
index finger and middle finger), and pull the
adjustment strap 15 forward with another hand
slowly, when the hand with shoulder strap touches
the child body, then stop pulling the adjustment strap
15, use the strength on shoulder strap properly.
1. Attach the two buckle latches Dtogether and engage them before putting them into the
harness buckle 6, this should make a clicking sound. Pull on the shoulder straps 5until the
harness lies flat and is close against your child's body. (See details 4-2 for how to adjust
shoulder strap)
2. Press red button Fto release the buckle.
Caution:
Please loosen the shoulder straps 5before
adjusting the headrest 1(See details 4-2).
Caution:
Please make sure the shoulder straps 5are not crossed and twisted.
3
5
16
15
5
15

4-5 ISOFIX installation and removal
4-6 Support leg installation and adjustment
4-7 Infant insert usage
ISOFIX installation
K
26
9 10
1. If your vehicle is not equipped with the ISOFIX insert
guides as shown, clip the two insert guides 26 which are
included with the seat, make sure the cut-out facing
upwards onto the two ISOFIX attachment point Kof your
vehicle.
TIP: The ISOFIX attachment points K are located
between the surface and the backrest of the vehicle seat.
2. Pull the grey fabric loop 23 to pull out both locking arms
24 and make sure the ISOFIX is completely pull out, there
is a noise of kakaka during the movement.
3. Push the ISOFIX 24 with both hands and
insert to both sides of ISOFIX insert guides
with a click sound .
4.Push the child seat with a substantial
amount of force as far as it will go.
Caution: The locking arms are only correctly
engaged if both of the ISOFIX indicators are
completely green.
5. Shake the child car seat to make sure it is
safely attached and recheck the ISOFIX
indicator to make sure that both of them are
completely green.
To adjust and install the support leg, pull the
support leg as far away from the back of the
child car seat as possible.
Push both adjustment buttons 12 and pull out
the support leg 11 until it rests firmly on the floor
of the vehicle.
The infant insert 4should be used when infant body weight
is below 13kg.
TIP: The infant insert ensure your baby's spine is supported
during travel.
TIP: Pull the support leg more if the indicator is
not green.
Caution:
the support leg indicator 13 must be
completely green.
Caution:
Please be aware, make sure you are pulling the
lower end of the strap. (see picture marked with red
circle)
23
24
CLICK
24
Isofix Removed from Vehicle Seat
1. Press Isofix second lock button 27 and
Isofix release button 25 together, press Isofix
release button 25, follow the red arrow
direction until Isofix 24 separated from the
vehicle seat.
2. Press both Isofix 24 until it retracts into car
seat base.
25
25
27
13
12
11
4

18
17
R
11 12
Caution:
1. Check the ISOFIX, support leg and harness system, make sure they work
properly, make sure your child is always securely fastened.
2. The ISOFIX locking arms are only correctly engaged if both of the ISOFIX
indicators are completely green.The support leg indicator 13 must be completely
green.
3. No cross or twist of the harness system.
4. The infant insert 4should be used when infant body weight is below 13kg.
5. ISOFIX insert guides are very helpful for ISOFIX installation 26.
1. Turn the child seat into forward facing position and move the seat into the upright
position (See details 4-1), pull the headrest to the highest position.(See details 4-3) and
take out the infant insert.
2. Open the harness buckle (Pic1), remove the shoulder pad (Pic 2) and buckle pad (Pic
3).
TIP: Split the shoulder pads before removing, then take down the shoulder pad strap 18
1. Install ISOFIX 24 onto vehicle seat (See details in 4-5), make sure it is completely
engaged and closed to vehicle seat.
2. Pull out support leg 11 until it rests firmly on the floor of the vehicle
3. Turn the child car seat to the lowest recline position (See details 4-1 )
4. Place your child securely in the child car seat.
1. Installed ISOFIX 24 onto vehicle seat(See details in 4-5), make sure it is completely
engaged and closed to vehicle seat.
2. Pull out support leg 11 until it rests firmly on the floor of the vehicle
3. Turn the child car seat to the recline position blue 1,2,3 (See details 4-1 )
4. Place your child securely in the child car seat.
3.Take down the headrest cover and shell cover carefully.
1. Turn the child seat into forward facing and move
the seat into the upright position
2. Fit the cover of headrest and shell carefully
3. Fit the shoulder pad and buckle pad.
TIP: The round plate Rwill be helpful when fitting the
cover.
TIP: The child car seat is always secured in the car via the ISOFIX anchoring, even when
there is no child in the seat.
4-8 Removing and Refitting the cover
Cover removing
Cover refitting
5 Installation
5-1 Rearward facing
Suitable for group 0+: weight 0-13kg (approx. birth-15 months)
Suitable for group 1: weight 9-18kg (approx. 9 months-4 years)
Pic 1 Pic 2 Pic 3
4
13
11
12
24
CLICK

13 14
Caution:
1. Check the ISOFIX, support leg and harness system ,make sure they work
properly, make sure your child is always securely fastened.
2. The ISOFIX locking arms are only correctly engaged if both of the ISOFIX
indicators are completely green.The support leg indicator 13 must be completely
green.
3. No cross or twist of the harness system.
4. ISOFIX insert guides are very helpful for ISOFIX installation 26.
Caution:
1. Before every journey, make sure that the rotating
part of child seat is fully engaged by trying to turn
the seat around in both directions.
2. Do not use the child seat forward facing when
your child is below 9 kg.
Caution:
Before every journey, make sure that the child seat
is in the right group and configuration for your child.
1. Install ISOFIX 24 onto vehicle seat(See details in 4-5), make sure it is completely
engaged and closed to vehicle seat.
2. Pull out support leg 11 until it rests firmly on the floor of the vehicle
3. Turn the child car seat to the recline position red 1,2,3 (See details 4-1 )
4. Place your child securely in the child car seat.
1. Grasp the turning knob 8and pressed safety button 10
simultaneously, change the lowest reclining position to
others.
2. Pull the rotation handle 14 and turn the seat into the
direction of traveling.
Pull the rotation handle 14 and turn the seat into against the
direction of traveling.
TIP: Grasp the turning knob 8and pressed safety button 10
simultaneously, change to the lowest reclining position for
group 0+.
The child car seat have a safety button 10 which must be pressed when changing
between group 0+ and group I. The safety button 10 is to prevent the child seat from being
mistakenly used for the wrong group of your child.
Caution! Rearward facing is suitable for group 0+ and group I, forward facing is
only suitable for group I.
5-2 Forward facing
Suitable for group 1: weight 9-18kg (approx. 9 months-4 years)
5-3 Change groups
A) Rotation function( from rearward to forward facing)
B) Rotation function(from forward to rearward facing)
4
13
11
12
24
CLICK
10
8
14
10
8
14

14
15 16
This child car seat 360° seat rotation which makes it easier
to get your child in or out of the child seat (Easy access
function).
Pull the rotation handle 14 and turn to 90°and into easy access mode.
CAUTION!
When the child seat in group 0+ mode, it can only turn to 90°. When the
child seat is in group I mode, it can turn to 360°
6. Side facing installation
Important:
The cover is a safety feature. Never use the child car seat without it, don’t put your child’s
safety at risk by using other replacement cover, they could stop the child seat from
protecting your child as well as it should be.
Washing instruction:
The cover is removable and washable at 30, line dry only.
7. Cleaning and Maintainance
Machine wash, cold Do not bleach Do not dry cleaning Do not tumble dry Do not iron
8. Notice 1
1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved by Regulation No.
44, 04 series of amendments for general use in vehicles fitted with ISOFIX anchorage
systems.
2. It will fit vehicles with positions approved as ISOFIX positions (as detailed in the
vehicle handbook), depending on the category of the child seat and the fixture.
3. The mass group and the ISOFIX size class for this device are intended for: Group
0+ (birth - 13kg) D, group I (9-18kg) B1.
Notice 2
This Child Restraint is classified for "Semi-universal" use and is
suitable for fixing into the seat positions of the following cars:
CAR
(See the car list) Yes Yes No
FRONT REAR
Outer Centre
Seat positions in other cars may also be suitable to accept this child restraint.
If in doubt, consult either the child restraint manufacturer or the retailer.