Koso DB-01 User manual

11
2 mm Allen key X 1
9 10
4 mm Allen key X 1 3 mm Allen key X 1
2-1
Wiring installation instructions
2-2
Installation instruction
A
C
B
Motor oil indicator can be set up, install as two stroke motor oil indicator, or other positive(+12V) or negative actions' indicator.
YAMAHA
HONDA
SUZUKI
KAWASAKI
SYM
KYMCO
PGO
Main power switch wire reference:
PowerGround
Brown
Brown
Black
Green
The color listed above may differ depending
on the model and year.
Black
Black
Black
Black
Green
Green
Key on
Red
Red
Red
Red
Red / White Orange
Green
Red / Black
White Black / Yellow
Yellow / Green
YAMAHA
HONDA
SUZUKI
KAWASAKI
BMW
BENELLI
APRILIA
Light Blue
Yellow / Blue
Yellow / Black
Black
Gray / Violet
Gray / Violet
DUCATI
BUELL
CAGIVA
H-D
MV
Gray / Green
Gray / Green
Gray / Yellow
Pink
Pink
RedTRIUMPH
RPM wire reference:
The color listed above may differ depending
on the model and year.
YAMAHA
SUZUKI
HONDA Yellow / White
Yellow / White
The fuel sensor is electronic type, do not connect
in parallel with the original wire - other wise
the fuel gauge won't display.
The wrong installation of the fuel
wire might damage the instrument.
Green
Fuel indicator wire reference:
KAWASAKI
SYM
KYMCO
PGO
Black / L Green
Gray
Yellow / White
Yellow / White
Brown / Red - RPM wire please
connect it to the suitable position
according to the models
R
(Accessories 4)
PM wire (TYPE B) PM wirR
(Accessories 3)
e (TYPE A)
Ignition coil positive
Pick up
R
(Accessories 4)
PM wire (TYPE B)
Tachometer
Flywheel
Ignition
pulse
Coil Spark plug wire
Spark plug Spark plug
cap
Active speed sensor (Accessories 5)
Connect to speed sensor
Black - Ground wire connect to the negative pole of
the battery (must be a good ground)
Brown - Positive wire should be connect to main
power switch
Red - Postive pole
(Connect to the
battery DC 12V)
Mid-way connector
Orange - L turn signal light (+12 V)
Blue - R turn signal light (+12 V)
Yellow - High beam light (+12 V)
Gray - Oil light (+12 V / ─)
White - Neutral light (─)
Green - Fuel
Purple - Engine light (─)
Yellow / White -
Water temperature light (─)
NOTE When connecting the power wire, please follow carefully the instruction. If the red & brown wires are connected in parallel, the meter won’t
work properly.
NOTE
The RPM wire installation
We recommend installing the R type spark plug or low-resistance spark plug cap at the same time.
A. Connect the RPM wire (TypeA) on the spark plug wire by connecting the male and female connectors.
B. Connect the RPM wire (TypeB) to the pick up sensor.
C. Connect in parallel the RPM wire (TypeA) with the original tachometer signal wire.
The best signal source will be in order as C>B>A, we will suggest you to check different ways if you have problems to get the
RPM signal.
When installing, please follow the steps bellow.
1.M5 x 12L screw x2 (Accesories 13)
2.Meter bracket for handle bar (Accesories 12)
3.Fix the bracket on handle bar (7/8 inch)
4.Bracket x1 (Accesories 12)
5.Meter (Accesories 1)
6.Meter board (Accesories 12)
7.M4 washer x2 (Accesories 15)
8.M4 x 10L screw x2 (Accesories 14)
Adjust the meter to the proper angle before tightening the
handle bar bracket screws.
NOTE
Special instruction for meter fix board.
A. Push meter bracket
clip up to lock meter
fix board with meter
on bracket
B. Push meter bracket
clip down to release
meter fix board with
meter on bracket
1
2
3
2
4
78
6
5
INSTALLATI O N
Thank you for purchasing the our product. Before installing, please read the instruction carefully and keep it for future reference.
Notice
◎Mark Meaning:
Some processes must be followed to avoid the damage to the vehicle.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
WARNING!
CAUTION!
NOTE Yo
NOTE Contact your local distributor, if the items received in the box are not the same as the items listed above.
NOTE Some of the optional accessories may not be available in your area. Contact your local distributor to obtain more information.
u could get the installation det ails from the information behind the m ark.
PRESS THE
BUTTON
ONCE
FLASH LIGHT ON
PRESS THE
BUTTON 3
SECONDS
Please, follow the step-by-step instructions for proper installation. Any damages caused by faulty installation shall be imputed tothe users.
●
●
To avoid a short circuit, do not pull the wires when installing the unit. Do not break or modify the wires either.
●
Do not disassemble or change any parts.
●
Maintenance and repairs should be executed by our professionals only.
●
1-1
Accessories
1-2
Accessories
1
Meter X 1
3 4
RPM wire (TYPE A) X 1 RPM wire (TYPE B) X 1
2
Main wiring harness X 1
6
M8 / S type speed
sensor bracket X 1
7
M10 / S type speed
sensor bracket X 1
Active speed sensor X 1
58
M5 X 5L mm Hexagon
screw X 2
15
Meter bracket X 1
13 14
M4 washer X 2
M4 X 10L screw X 2
12
M5 X 12L screw X 2
JIS TYPE A
1
Digital speed signal
sensor
RUNNER
2
Digital speed signal
sensor
SR
X-FIGHT
BOOSTER
3
Digital speed signal
sensor
5
Meter bracket
4
LTYPE speed sensor
backet
wh041ba02a(P6-1)

Speedometer
●Display range :
0 ~ 360 km/h (0 ~ 225 mile)
Maximum speed record
●Display range : 0 ~ 360 km/h (0 ~ 225 mile)
Maximum RPM record
●Display range : 0 ~ 15,000 RPM
Odometer
●Display range : 0 ~ 99999.9 km (mile),
return to zero upon exceed.
●Display unit : 0.1 km (mile)
Trip meter A、B
●Display range : 0 ~ 999.9 km (mile),
return to zero upon exceed.
●Display unit : 0.1 km (mile)
Tachometer
●Display range : 0 ~ 15,000 RPM
●Display unit : 10 RPM
Voltmeter
●Display range : DC 8.0 V ~ 16.0 V
●Display unit : 0.1 V
3-1
Basic function instruction
3-2
Function, setting instructions
MOTO / SCOOTER
MOTO / SCOOTER
spee d
sensor
be lo w
8m m
EX. 4 Rear disc - detect the gap between the disc.
Install the s type sensor bracket.
Adjust the sensor bracket position to make
sure that the sensor could face the magnet
to prevent bad speed signal or no signal!
Install the speed sensor on the bracket.
Adjust the distance between sensor and
magnet. We suggest you to make sure the
distance is under for catching good
speed signal.
1 mm
S type speed sensor bracket instruction
L type speed sensor bracket instruction
Please install the L bracket and the anti-slip
rubber on the front fork and adjust it to the
proper height and angle.
Please use the cable tie to fix the bracket on
the front fork. Please make sure the disc
screw could pass the hole on the bracket for
you to install the sensor into the same hole for
catching the speed signal.
Install the speed sensor on the bracket.
Adjust the distance between sensor and
magnet. We suggest you to make sure the
distance is under for catching good
speed signal.
1 mm
After installation, please use your hand to turn the tire to see is everything ok. The LED on the active speed sensor will light up once
the signal is detected.
EX. 1
The active speed sensor could be installed by the metal parts to detect the speed.
EX. 1 The disc screw.
EX. 2 The disc to detect the disc gap. (Please make sure the distances between the gaps are the same in advance to avoid wrong
speed signal.)
EX. 3 The sprocket to detect the disc gap. (Please make sure the distances between the gaps are the same in advance to avoid wrong
speed signal.)
We will suggest you to catch the speed from the disc screws. The more the sensor points are, the better the speed accuracy is. The
maximum sensor points the speed sensor could detect is 20 points per turn.
speed
sensor
speed
sensor
the det ect ran ge
speed
sensor
speed
sensor speed
sensor
the det ect ran ge
speed s ensor speed s ensor
the det ect ran ge
speed s ensor speed s ensor
the det ect ran ge
EX. 2 、 4 EX. 3
The hexagon socket disc screw
The best detect area: The edge of
the hexagon socket screw.
Please don't catch the signal from
the middle hole of the hexagon
socket screw to avoid wrong signal.
The hexagon screw
The best detect area: The middle
of the screws.
Some hexagon screw center is with a small
hole in the center in this case,we will suggest
you to catch the signal from the edge of the
screw like the hexagon socket screw.
The disc
The best detect area: Please detect
the speed signal from the gaps of the disc.
Please note that there are discs with
the gaps in different difference, and
this method will not work on it!
The sprocket
The best detect area: Please detect the
speed signal from the gaps of the sprocket.
Please note that there are sprockets
with the gaps in different difference,
and this method will not work on it!
Indication light
●Neutral (green light)
●
●
Right indication light (green light)
Water temperature (red light)
●
●
Motor oil (red light)
Engine (yellow light)
●
Left indication light (green light)●
Fuel (yellow light)
●High beam light (blue light)
Average speed record
●Recording range :
0 ~ 360 km/h (0 ~ 225 MPH)
Tachometer
●Display range : 0 ~ 10,000 RPM、0 ~ 12,000 RPM、0 ~ 15,000 RPM
Fuel Level
●Setting range : 100Ω、 250Ω
、270Ω、510Ω、1200Ω、
SWITCH、USER
Low fuel warning
●Setting range : 10 ~ 50%,
when lower than (including)
setting value, fuel level
symbol will blink.
Total engine operating time
●
●
Display range : 0~99,999.9 hours
Display unit : 0.1 hour
Engine operating time A,B
●
●
Display range : 0~9,999.9 hours
Display unit : 0.1 hour
AdjustSelect
Internal ODO
●
●
Display range : 0 ~ 99,999.9 km (mile) ,
user unadjustable.
Display unit : 0.1 km (mile)
External ODO
●
●
Setting range : 0 ~ 99,999 km (mile)
Setting unit : 1 km (mile)
●
Clock format
●Setting range : 12 - hrs format, 24 - hrs format.
Clock
Setting range : 0：00 ~ 23：59 (24 - hrs format),
1：00 ~ 12：59 (12 - hrs format)
●
●
●
Motor oil maintenance millage
Display range : SI unit :
500 (~ 8,000 km, user adjustable) ~ -999 km, automatic decrease according to the increase of total millage.
Display range : Inch :
300 (~5,000 mile user adjustable)~ -999 mile, automatic decrease according to the increase of total millage.
Display unit : 1 km (mile)
●Speedometer Display range : 0 ~ 360 km/h (0 ~ 225 MPH)
Will blink when exceed range.
Display unit : 1 km (mile)
○ Display internal
○
Trip meter A、B
○
Odometer
<0.5 second
Display range : 0 ~ 99,999.9 km (mile), return
to zero upon exceed.
Display unit : 0.1km (mile)
Display range : 0 ~ 999.9 km (mile), return to
zero upon exceed.
Display unit : 0.1km (mile)
○
Maximum speed record
Display range : 0 ~360 km (0 ~ 225 mile)
Display unit : 1 km (mile)
○
Average speed recordRecording range : 0 ~ 360km/h (0 ~ 225 MPH)
○
Tire circumference Setting range : 300 ~ 2,500 mm
Setting unit : 1 mm
○
Sensitive point Setting range : 1 ~ 20 points
Setting range : 1 point
○
The RPM input signal number setting Setting range : P-0.5,P-1~P-25
○
The RPM input pulse Setting range : lo-Act, Hi-Act
○ Display internal <0.5 second
●
Tachometer Display range : 0 ~ 15,000 RPM
Display unit : 10 RPM
○
Stage tachometer Display range : 0 ~ 10,000 RPM、
0 ~ 12,000 RPM、0 ~ 15000 RPM
Display unit :
0 ~ 10,000 RPM (333 RPM each stage)
0 ~ 12,000 RPM (400 RPM each stage)
0 ~ 15,000 RPM (500 RPM each stage)
○
MAX RPM record Display range : 0 ~ 15,000 RPM
Display unit : 10 RPM
●
Total hour meter Display range :0 ~ 99,999.9 hour
Display unit : 0.1 hour
○
Display range :0 ~ 9,999.9 hour
Hour meter A、B
Display unit : 0.1 hour
●Motor oil maintenance
millage
●
Fuel level Setting range : 100Ω、 250Ω,、270Ω、510Ω、
1200Ω、SWITCH、USER
○ Staged fuel gauge
○ Digital fuel gauge Setting range : 0 ~ 100 %
● External ODO Setting range : 0~99999 km (mile)
Setting unit :1km (mile)
●
Effective voltage
●
Effective temperature range
●
Meter weight
●
Meter size
●
Meter standard
120 x 46 x 20 mm
Around 240 g
DC 12 V
JIS D 0203 (S2)
-10 ~ +60 °C
●
Backlight color Display range: white
Setting unit : 1 hour
● Clock format Setting range : 12-hrs format, 24-hrs format
○
Setting range : 0 ~ 23 (24-hrs format),
1 ~ 12 (12-hrs format)
Clock (hours)
○ Clock (minute) Setting range : 00:59 minutes
Display range : 1 minute
● Volt meter Display range : DC8.0 V ~ 16.0 V
Display unit : 0.1V
●
Internal ODO Display range : 0~99999.9 km (mile), user
unadjustable
Display unit : 0.1 km (mile)
●
Indicator light Neutral (green light)
Right indication light (green light)
Water temperature (red light)
Motor oil (red light)
High beam light (blue light)
Left indication light (green light)
Fuel (yellow light)
Engine (yellow light)
Setting unit : 10 %
○ Low fuel warning Setting range : 10 ~ 50 %, when lower than
(including) setting value, fuel level symbol will blink.
Setting unit : 10%
Display range : SI unit : 500 (~8000 km, user adjustable)
~ -999 km, automatic decrease according to the
increase of total millage.
Display range : Inch : 300 (~ 5000 mile user adjustable)
~ -999 km, automatic decrease according to the
increase of total millage.
Display unit : 1 km (mile)
Setting range : 10 stage display
Warning range : Fuel level warning stage below
(including) setting value, fuel level symbol will blink.
NOTE Any design and specification changes will not be notify.
wh041ba02a(P6-2)

3-3
Meter size
3-6
The settings screen description
4
Enter settings and function index menu
a 1. Circumference and sensing pointsetting
a 2. RPM pulse setting
a 3. Fuel gauge resistance setting
Fuel level manual setting
Fuel level resistance auto detection setting
Fuel warning setting
a 4. Clock setting
a 5. Backlight brightness setting
a 6. Oil maintenance mileage setting
a 7. Speed unit setting
a 8. External ODO
a 9. Internal ODO
●Press and hold the Select + Adjust
button for 3 seconds to enter setting
screen.
4-1
4-2
4-3
4-3-1
4-3-2
4-3-3
4-4
4-5
4-6
4-7
4-8
4-9
--------------------------
----------------------------------------------
------------------------------------
-------------------------------------
--------------------
------------------------------------------
----------------------------------------------------
--------------------------------------
---------------------------------
-----------------------------------------------
---------------------------------------------------
----------------------------------------------------
●Function index
3-5
Adjust button function instruction
3-4
Select button function instruction
●In the ODO sereen, press the
Select+Adjust buttons for 3 seconds
to enter settings (Please refer to 4).
●In the ODO sereen, press the Adjust
button to enter the Trip A screen.
●In the Trip B screen, press the Adjust
button to enter the oil maintence
mileage screen.
●Press and hold the Adjust button for 3
seconds to reset Trip B screen.
●In total hour meter screen, press the
Adjust button to enter the hour meter
A screen.
●In the Trip A screen, Press the Adjust
button to enter the Trip B screen.
●Press and hold the Adjust button for 3
seconds to reset Trip A screen.
●In the hour meter A screen, press the
Adjust button to enter the hour meter
B screen.
●Press and hold the Adjust button for 3
seconds to reset hour meter A screen.
●In the hour meter B screen, press the
Adjust button to enter the Max. record
screen.
●Press and hold the Adjust button for 3
seconds to reset hour meter B screen.
●In the Max. record screen, press the
Adjust button one time to enter the
Average speed record screen.
●Press and hold the Adjust button for 3
seconds to reset Max. record screen.
●In the Average speed record screen,
press the Adjust button one time to
enter the ODO sereen.
●In the ODO sereen.
●Press and hold the Adjust button for 3
seconds to reset Average speed record
screen.
●In the oil maintence mileage screen,
press the Adjust button to enter the
total hour meter screen.
●Press and hold the Adjust button for 3
seconds to reset oil maintence mileage
screen.
●In the fuel level screen, press the
Select button one time to go back to
the clock screen.
In settings screen, button is not pressed in 30 seconds, or speed > 3 km/h,
will automatically return to main screen.
After exiting settings screen, it will record the parameters.
NOTE
NOTE
●Total millage screen - Press and hold the Select + Adjust button for 3 seconds to
enter setting screen.
●Press the Adjust button to select setting screen for Circumference and sensing
pointsetting, RPM pulse setting, Fuel gauge resistance setting (Fuel level manual
setting / Fuel level resistance auto detection setting / Fuel warning setting), Clock
setting, Backlight brightness setting, Oil maintenance mileage setting, Speed unit
setting, External ODO, Internal ODO.
●In any setting screen, hold the Select button for 3 seconds to return to main screen.
●In the clock screen.
●In the volt screen, press the Select
button one time to enter the fuel
level screen.
●In any screen, press and hold the
Select buttons for 3 seconds to switch
between rpm and fuel bar screen.
●In the clock screen, press the Select
button one time to enter the volt
screen.
120 mm
46 mm
20 mm37 mm
8 mm
4-1
Circumference and sensing pointsetting
●Press the Select button to enter the
circumference and sensing point
setting screen.
●Example：If the tire circumference is
1,300 mm.
●Press the Select button to choose
the setting number.
●EX. Now the tire circumference is
setting from 1,000 mm.
●Press the Adjust button to choose
the setting number.
Please reset this setting value when
you change a different size tire.
●Please measure the tire circumference (
The tire you will install the sensor on) and
make sure the number of magnet sensor
point (You could install the magnet into
the disc screw or the sprocket screw.)
●The speed displayed on the meter will be
affected by the setting, please make sure
the setting number is correct before you
make the setting.
NOTE Setting range：300 ~ 2,500 mm
Setting unit：1 mm
Now the digit in thousands setting
number is flashing!
P.S.
●You could define the
valve as the starting
point and the terminal
point to measure the
wheel circumference
with a measuring tape.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back to
the circumference and sensing point
setting screen.
●Ex. Now the sensor point is setting
from 1P to 6P.
●Press the Select button to enter the
sensor point setting.
●EX. The circumference setting is
changed from 1,000 mm to 1,300 mm.
NOTE Sensitive point：1 ~ 20
Now the setting value is flashing!
●Example：If the sensor point is
setting 6P.
●Press the Adjust button to choose
the setting number.
●Ex. Now the sensor point is setting
from 1P.
wh041ba02a(P6-3)

●Press the Select button to enter the
lowest fuel level's resistance setting
screen.
●Example：For YAMAHA T-MAX 530,
according to the service manual, the
fuel tank resistance from low to high
is 90 - 100 Ω (the lowest) and 4 - 10 Ω
(the highest).So enter the setting
value as 10 Ω .
4-3-2
Fuel level resistance auto detection setting
4-3-1
Fuel level manual setting
●Press the Select button 5 times to
enter the lowest fuel level resistance
auto detection screen.
●EX. Auto Detection the lowest fuel
level resistance is 90 Ω.
P.S.
P.S.
●For example of YAMAHA T-MAX 530,
if the fuel surface sensor float in the
lowest position then it will detect the
resistance around
90 Ω.
●Press the Select button to enter the
lowest fuel level's resistance auto
detection screen.
●Press the Adjust button to detect the
lowest fuel level's resistance.
The lowest position
●Before detection, ensure that your current
fuel level is in the lowest position that you
would like to have.
●Stop the vehicle for a few seconds to allow
the fuel surface to become steady, then
start the detection of the resistance.
●Before detection, please ensure your
current fuel level is in the highest
position that you would like to have.
●Stop the vehicle for a few seconds to
allow the fuel surface become steady,
then start the detection of the resistance.
P.S.
●For example the YAMAHA
T-MAX 530, if the fuel surface sensor
float is in the highest position then it
will detect the resistance as around 10 Ω.
●Press the Adjust button to detect the
highest fuel level resistance.
●Press the Select button 5 times to go
back to the fuel gauge resistance.
●EX. Automatically detect the highest
fuel level resistance value as 10 Ω.
The highest position
Currently setting value will blink.
●Example：To set maximum fuel level
as 10.
●Press the Select button to choose
the setting number.
●
Press the Select button twice to enter
maximum fuel resistance value setting
screen.
● EX：Setting minimum fuel level
from 0 to 90.
●Press the Select button twice to enter
4-3-3 fuel warning setting menu.
●EX. The highest fuel level setting is
changed from 0 to 10 Ω.
●Press the
Adjust button to choose
the setting number.
Currently setting value will blink.
●Example：To set minimum fuel level
as 90 Ω.
●Press the Select button to choose
the setting number.
●Press the Adjust button to choose
the setting number.
●You could find your fuel level sensor
resistance range in the electronic
components section in the service
manual.
●Normally, we will recommend to choose the
closest number set as the range to ensure that riders
will not run out of gas before the fuel level indication. example, for
YAMAHA T-MAX it’s 90 - 100 Ω and 4 - 10 Ω , in which case we will
suggest to use 90 - 10 Ω as the lowest and highest range.
wh041ba02a(P6-4)
Currently setting value will blink.
4-3
Fuel gauge resistance setting
●Press the Select button to enter 4-3-3
fuel warning setting screen.
●EX. Setting fuel meter's resistance
value from 100 to 270.
●Press the Select button to enter the
circumference and sensing point
setting screen.
NOTE The fuel gauge resistance
setting range：USER、100 Ω、
250 Ω、270 Ω、510 Ω、
1200 Ω、SW (turn off)
NOTE
NOTE Fuel meter will be displayed with
the wiring connected.
Custome fuel level resistance:
1) Manual - Please check 4-3-1
Fuel Level Resistance Manual
Setting Instructions.
2) Auto - Please check 4-3-2
Fuel Level Resistance Auto
Setting Instructions.
●Example: If the vehicle is a YAMAHA
T-MAX 530, it's resistance is 100 Ω
according to the service manual.
●Press the Adjust button to choose the
setting number.
NOTE
Setting range: 0.5、1 ~ 25
Currently setting value will blink.
4-2
RPM pulse setting
NOTE
●EX. You want to connect the RPM
signal wire to the pick up signal and
there are 13 flywheel signals per turn.
●Press the Adjust button to choose the
setting number.
●Press the Select button to enter the
RPM pulse setting screen.
Setting range：Hi-Act、Lo-Act
●Example : To set waveform to high
waveform (Hi-Act).
● Press the Adjust button to choose the
setting number.
NOTE
Currently setting value will blink.
NOTE Setting range：10,000、
12,000、15,000 RPM。
Currently setting value will blink.
●Press the Select button to enter
waveform setting screen.
●EX. Setting engine ignition angle from
P-1 to P-13.
During RPM signal detection,
if there is any bad sensing or
interference, please select
another RPM sensing waveform.
●Press the Select button to choose
the setting number.
●Example : To set rpm stage value as
10,000 RPM.
●EX. Current rpm stage value is
15,000 RPM.
●Press the Select button to enter rpm
stage setting screen.
●EX. Setting from high wave (Hi-Act) to
low wave (Lo-Act).
●Press the Adjust button to enter next
operation setting.
●Press the Select button to return to
rpm stage setting screen.
●EX. Setting rpm stage value form
15,000 RPM to 10,000 RPM.
●Press the Adjust button to choose
the setting number.
The corresponding RPM signal
number per ignition.
2C-1P 4C-2P
4C-4P2C-2P
The
setting
value
0.5
2
4C-6P2C-3P
3
4C-8P2C-4P
4
4C-10P
5
2 RPM signals per 1 ignition.
1 RPM signal per 1 ignition.
1 RPM signal per 2 ignition.
1 RPM signal per 3 ignition.
1 RPM signal per 4 ignition.
1 RPM signal per 5 ignition.
1 RPM signal per 6 ignition.4C-12P2C-6P
6
1
4C-1P
The correspond-
ing stroke and
pistons number.
Most of the 4-cycle bikes
with one single piston are igniting every
360 degree once, so the setting should
be the same as the bike with 2-cycle
and one piston engine.
CAUTION!

4-3-3
Fuel warning setting
Setting range：00 ~ 59 minutes.
NOTE
4-4
Clock setting
4-5
Backlight brightness setting
4-6
Oil maintenance mileage setting
4-8
External ODO
4-7
Speed unit setting
Setting range：
1 (Darkest) ~ 5 (Brightest),
5 different levels available.
Setting unit：20% per level.
The backlight brightness will
change immediately after you
set the value.
NOTE
Setting range :
0 ~ 99,999 km (mile)
NOTE
Setting range : 2T / 4T
NOTE
●Press the Select button to enter the
external ODO setting screen.
Currently setting value will blink.
●Example : To set external total millage
value to 12,500 km.
●Press the Select button to choose
the setting number.
●Press the Adjust button to choose
the setting number.
●Press the Select button to the
external ODO setting screen.
●EX. The external ODO is changed 0 to
12,500 km.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to enter the
speed unit setting screen.
●Press the Adjust button to choose
the setting number.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back
speed unit setting screen.
●EX. The speed unit setting is changed
km/h、km to MPH、mlie.
●Press the Select button to enter the
oil maintenance mileage setting
screen.
●Example：To set motor oil millage
value as 4T.
●Press the Adjust button to choose
the setting number.
●EX. Current motor oil millage is 2T.
Currently setting value will blink.
●Press the Select button to enter 4T
motor oil millage setting main screen.
●EX. Setting motor oil millage value
from 2T to 4T.
●Press the Adjust button to choose
the setting number.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back
oil maintenance mileage setting
screen.
●EX. Setting motor oil millage
parameter from 1,000 to 1,500.
●Press the Select button to choose
the setting number.
●Example：To set motor oil millage
parameter as 1,500.
●EX. Current motor oil millage
parameter is 1,000.
NOTE
●2-stroke motor oil millage is
indicated by external signal warning
(motor oil indicator will lit).
●4-stroke motor oil millage is internally
set by the chronograph.
Currently setting value will blink.
●Press the Select button to enter the
backlight brightness setting screen.
Currently setting value will blink.
●Example：You want to set the
brightness at 60 % (3).
●Press the Adjust button to choose
the setting number.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back to
the backlight brightness setting screen.
●EX. The backlight brightness setting is
changed from 5 (100%) to 3 (60%).
Currently setting value will blink.
●Example：Changing the 24H.
●Press the Adjust button to choose
the setting number.
●Press the Select button to enter the
clock setting screen.
●Press the Select button to enter time
adjustment (hour / minute) setting
screen.
●EX. Setting time format from 12-hours
to 24-hours.
Cursor moving order is：
Hour > Digit in ten minutes >
Digit in minutes
NOTE
Setting range：0 ~ 23
NOTE
Currently setting value will blink.
NOTE
Currently setting value will blink.
●Example：To set time(hour) as 10
hours.
●Press the Adjust button to choose
the setting number.
●Press the Adjust button to enter next
operation setting.
Now the setting value is flashing!
●Example：To set time (minute) as 10
minutes.
●Press the Select button to choose
the setting number.
●Press the Select button to return to
time setting screen.
●EX. Setting hour/minute from 0 hour
0 minute to 10 hours 10 minutes.
●Press the
Adjust button to choose
the setting number.
NOTE
Setting range: 12 / 24 H
●Press the Adjust button to enter next
operation setting.
●Example：To set fuel warning value
as 30%.
●Press the Adjust button to choose
the setting number.
Setting range : 10%, 20%, 30%,
40%, 50%.
Fuel meter will not display when
fuel meter's wire is not installed.
●Press the Select button to return to
fuel level resistance value setting
screen.
●EX. Setting maximum fuel level from
30% to 10%.
wh041ba02a(P6-5)

●The power doesn't supply to the meter.
→Please make sure the wiring is
connected.
The wiring and fuse are not broken.
→The battery is broken or the battery is
too old to supply enough power
(DC 8 V) to make the meter work.
●
make sure the voltage is over DC 8 V.
●Make sure the speed sensor is
connected properly.
→Please check if speed sensor is
connected and working properly. Also
check whether the cable of speed sensor
has broken or lose or not.
●Check the tire-size setting.
→Refer to the manual 4-1 circumference
and sensing point setting.
The following situation do not indicate malfunction of the meter.Please check the following before taking it in for repair.
The meter doesn't work when
the power is on.
The meter shows wrong
information.
Speed does not appear or
appear incorrectly.
Check the voltage of your battery,and
●
●
→
●
Fuel gauge does not appear
or appear incorrectly.
The odometer and trip meter
is not accumulated or
accumulated wrong data.
Check your fuel tank.
Check the wiring harness.
Is the wire connected properly.
Check the tire-size setting.
→Refer to the manual 4-3 fuel gauge
resistance setting.
●It is possible that the permanent power
Tachometer does not appear
or appear incorrectly
● Please check the RPM sensor wiring is
connected correctly.
● Please check the spark plug is R type or
not. If not, please replace the spark plug
with the R type spark plug.
● Please check your setting.
→Please refer to the manual 4-2 RPM
pulse setting.
wire is not connected well.
→Please check the red positive wire is
connect well or not.
* If the problem is not resolved after following the steps shown above, please contact your loval distributor for assistance.
● It is possible that the permanent power
wire is not connected properly.
→Check if the red positive wire is
connect propery.
The odometer and trip meter
are not accumulated or
accumulated the wrong data.
Check itemTrouble Check itemTrouble
●Example：Current internal ODO is
50,000 km.
●Press the Select button three seconds
to go back to ODO screen.
●The main screen.
Setting range：
99999.9 km (mlie).
User unable to adjust and
clearinternal ODO.
NOTE
4-9
Internal ODO
5
Trouble shooting
wh041ba02a(P6-6)