Koso EX-01 User manual

wh049ba01a
4
M3XP0.5 screw nut X2
5
Velcro X1 set
1
警告!
2
1
For proper installation, please follow the steps described below. Any damage caused by a wrong installation shall be imputed to the users.
●
Do not cut or modify the wire. To avoid short circuit, do not pull the wire off the connector when installing the meter.
●
Do not disassemble or change any parts
●
Opening the instrument will void any warranty. Maintenance or repair should be executed by our professionals only.
●
◎MARK MEANING:
WARNING!
CAUTION!
Some procedures must be followed to avoid damage caused by wrong installation.
Some procedures must be followed to avoid injuries.
Some procedures must be followed to avoid any damage to the vehicle.
PRESS THE
BUTTON
ONCE
PRESS THE
BUTTON 3
SECONDS
Kit content
Meter X1 M3X10XP0.5 screw X2
3
M3 washer X2
Please contact your local distributor if the items received are not the same as the ones listed above.
A
2-1
2-2
A
B
RPM / Hour Meter
A
B
Installation instruction
Installation steps
1. Engine hour meter (Accessory 1)
2. M3 screw (Accessory 2)
3. M3
washer (Accessory 3)
4. M3 screw nut (Accessory 4)
1. Engine hour meter (Accessory 1)
2. Velcro
- Male (Accessory 5)
3. Velcro - Female (Accessory 5)
Choose either Method A or B according to your need.
Wiring installation instruction
Brown / RPM wire
Connect the RPM wire
according to one of the
three positions shown on
(B). the models.
Spark plug wire
For motorcycle with ignition coil system, the RPM can be
installed following the methods here described. Wrap the
RPM wire at least 5 times around the spark plug cap as
shown below.
Thank you for purchasing our Koso EX-01 engine hour meter. Please read carefully the instruction sheet and keep it for future
Notice
A
1.
2.
4.
B
1.
2.
3.
3.

4
26.8 mm
14.9 mm
42.8 mm
3
●
●
●
●
●
Design and specifications are subject to change without notice!
Specifications
Functions instruction
While on Total Engine Hour screen, press
the button once to enter the Engine Hour A.
In Engine Hour A, press the button once to
enter the Engine Hour B.
While on Engine Hour B, press the button
once to enter the Total Engine Hour.
Holding the button for 3 seconds will reset
the Engine Hour A record.
Display range : 0~9999 H
Display unit : 1 H
●Totalenginehour meter
Display range : 0.0~999.9 H
Display unit : 0.1 H
●Hour meterA/B
When the engine hour meter starts to
count, the “ t ’ symbol will flash every
0.5 second. Holding the button for 3 seconds will
reset the Engine Hour B record.
5
症狀
Troubleshooting
The meter will automatically turn off if no button is pressed or if there is no signal input for more than 30 seconds.
The followingsituation does not necessarily indicate a malfunction to the meter. Check the following before takingitin for warranty.
Problem
The digits do not appear or
appear incorrectly.
※If the problem can still notbe solved, please contact your local distributor.
Check if the RPM wire is connected properly.
The meter ran out of battery and shall be replaced.
Diagnosis
-10~60
JIS D 0203
●Effective temperature range
●Internal battery type
●Meter weight
●Meter size
●Meter standard
●Battery life time About 350 hours
+ or - 19g
CR 2032
W42.8 X L26.8 XH14.9 mm
About 5 years
●Battery self-consumed life time
℃
wh049ba01a