Koso DL-04 User manual

wh077ba07a(P15-1)
24
M6 Bushing X2
25
M8 Bushing X2
19
M5 washer X3
10 M8 / S type speed
sensor bracket X 1 11 M10 / S type speed
sensor bracket X 1 12 M5x5xP0.8 Hexagon screw X 2
13 2.5 mm Allen key X 1
2
Main wiring harness X1
20
M6 x 35L Allen screw X2
21
M8x30L Allen screw X2
22
M6 Bushing X2
23
M8 Bushing X2
14 3 mm Allen key X1
17
M5x16L mm Screw X1
18
M5x12L mm Screw X2
16
Bracket sleeve X1
15
Meter bracket X1
9Rubber strip X1
1LCD Meter
X1
6
Extension wire X1
8External switch
(Dual button type) X1
7
Temperature sensor X1
5
RPM wire set (TYPE B) X1
3
Active speed sensor X1
4
RPM wire (Type A) X1
Accessories
1-1
Thank you for purchasing our product. Before installing/operating the product, read the instructions carefully and retain them
for future reference.
Attention!
●For installation, follow the steps described. Any damage caused by wrong installation shall be imputed to the users.
●To avoid a short circuit from occuring do not pull or modify the wires during installation.
●Do not disassemble or change any parts. Opening and dissassembling this unit will void any warranty.
●Maintenance and repairs should be executed by our professionals only.
NOTE
WARNING!
Some procedures must be followed to avoid damages to the instrument.
Certain procedures must be followed to avoid damages to yourself, to the vehicle or to others.
Light onFlash
Hold the
Button
3 seconds
Hold the
Button
1 second
Symbol description:

wh077ba07a(P15-2)
Main wiring (Accessory 2)
LCD Meter (Accessory 1)
The fuel sensor is electronic type. Do not
connect in parralel with the original wire,
otherwise the fuel gauge won't display.The
wrong installation of the fuel wiring may cause
the meter to be damaged.
Blue- R turn signal light (+12V)
Purple- Engine light (-)
Wiring Installation Instructions
2-1
Yellow- High beam light (+12V)
Green- Fuel
Black / Ground wire connect to the negative pole of the battery.
Extension wire
( Accessory 6 )
Temperature sensor( Accessory 7 )
Install the temp sensor
to the position.
Yellow-white/White-
black-Temperature
sensor terminals
Blue-red/Blue-white/White-black
Connect to speed sensor
Active speed sensor
(
Accessory 3 )
Brown-red RPM wire
connect it to the
suitable position according
to the models.
Brown - Positive wire
should be connect to
main power switch
NOTE When connecting the power wire, follow carefully the instructions. If the red & brownwires are connected in parallel, the
meter will not twork properly.
The RPM wire installation
We recommend installing the R type spark plug or low-resistance spark plug cap at the same time.
A. Connect the RPM wire (Type A) on the spark plug wire by connecting the male and female connectors.
B. Connect the RPM wire (Type B) to the pick up sensor.
C. Connect in parallel the RPM wire (Type A) with the original tachometer signal wire.
The best signal source will be in order as C>B>A, we will suggest that you check different ways if you have problems
getting the RPM signal.
Mid-way connector
Red / Postive pole
(Connect to the battery DC 12V)
Ignition
pulse
RPM wire set(TYPE B)
(
Accessory 5 )
RPM wire set(TYPE B)
(
Accessory 5 )
RPM wire (Type A)
(
Accessory 4 )
Ignition coil positive
Tachometer Pick up
Spark
Spark plug cap
Coil Spark plug wire
Flywheel
A
BC
Green- Red - ABS light
Gray- Motor oil light (-)
White- Neutral light (-)
Orange- L turn signal light (+12V)
The color listed above may differ depending
on the model.
The color listed above may differ depending
on the model.
External switch
(Accessory 8)
Brown-white/Red-white/White-red
Push button switch terminal
Optinal accessories
1-2
3
Water temp sensor
adapter
M14
M16. M18
M22. M26 mm
1
L type speed sensor
bracket
2
Oil temp sensor adapter
M12 X P1.5 X 15L
M14 X P1.25 X 15L
M14 X P1.5 X 15L
M16 X P1.5 X 15L
M18 X P1.5 X 15L
M20 X P1.0 X 15L
M20 X P1.5 X 15L
BI003S01 BG0*****BG******
Some of the optional accessories may be purchase separately. For more details, contact your local distributor.
NOTE

Installation instructions
2-2
wh077ba07a(P15-3)
6. 7.
8.
8. 8.
9.
10.
10.
11.
1.
1.
2.
2.
5.
4.
3.
4.
5.
1.
4.
5.
0.6 Nm (6 kgf.cm)
T
R
.
2.
3.
Follow the steps below during installation.
Handle bar
Rubber strip (Accessory 9)
External switch (Dual button type) - Upper case (Accessory 8)
External switch (Dual button type) - Bottom case (Accessory 8)
M3x12xP0.5 mm screw
1.
2.
3.
4.
5.
Handle bar SIZE
7/8”(22.2 mm)
1”(25.4 mm)
Use Rubber strip
NO
YES
Total length of wiring is 600 mm. Pay attention to
the distance between the wire exit hole and the
end of handlebar to avoid insufficient wire length.
CAUTION!
Refer to the list below and decide whether to
use rubber strip according to the grip diameter.
CAUTION!
1. M6 or M8 Allen screw X2 (Accessory20,21)
2. M6 or M8 Bushing X2 (Accessory22,23)
3. Meter bracket (Accessory15)
4. M6 or M8 Bushing X2 (Accessory24,25)
5. Handle bar bracket
6. LCD Meter (Accessory1)
7. Bracket sleeve (Accessory16)
8. M5 washer X3 (Accessory19)
9. M5x16L mm Screw (Accessory17)
10. M5x12L mm Screw X2 (Accessory18)
11. Meter bracket micro-adjustment screw 0.45 Nm (4.5 kgf.cm)
1.2 Nm (12 kgf.cm)
1.1 Nm (11 kgf.cm)
Follow the steps below during installation.
You can also install it (meter bracket) on the
original meter bracket.
NOTE
MOTO / SCOOTER
Install t he S t ype sensor bracket.
Adjust the sensor b racket p osit ion to m ake
sure t hat t he sen sor faces t he m agn et t o
prevent bad speed signal or no signal.
Inst all t he sp eed sensor o n t h e b racket .
Adjust the distance between sensor and
magnet. We suggest you make sure the
distance is under 1 mm for an optimal
speed signal.
S type speed sensor bracket inst ruct ion
below
1 mm
below
1 mm speed
sensor
speed
sensor
MOTO / SCOOTER
L type speed sensor bracket inst ruct ion
Install the L bracket and the anti-slip
rubber on the front fork and adjust it to the
proper height and angle.
Use the zip tie to fix the bracket on
the front fork. Make sure the disc
screw could pass the hole on the bracket for
you to install the sensor into the same hole for
catching the speed signal.
Install the speed sensor into the proper
hole on the bracket.
Adjusting the distance between the sensor
and screw to get the best speed signal.
Make sure the distance is under 2mm
to get the best signal.

wh077ba07a(P15-4)
3-2
Basic Function Instructions
Indicator
●Check engine light (Amber) ●High beam light (Blue) ●Neutral light (Green) ●Warning light (Red)
●ABS light (Amber) ●Turn signal light (Green) ●Shift light
Gear Meter
●Display range : OFF, - , N, 1~the highest gear
Tachometer
●Display range : 0~10,000 RPM、0~15,000 RPM
●Display unit : 111 RPM / 166 RPM
Odometer
●Display range : 0 ~99,999 km (mile)
●Display unit : 1 km (mile)
Trip meter A, B
●Display range : 0.0~9,999.9 km (mile)
●Display unit : 0.1 km (mile)
Motor oil maintenance (Trip O)
●Display range : OFF, -999~16,000 km
(-999~10,000 mile)
●Display unit : 1 km (mile)
Speedometer
●Display range : 0 ~360 km/h (0 ~225 MPH)
●Display unit : 1 km/h (MPH)
Clock
●Setting range : 00:00~23:59 (24H)
01:00~12:59 (12H)
Voltmeter
●Display range : DC 8.0 ~ 18.0 V
●Display unit : DC 0.1 V
Temperature
●Display range : 0.0~250.0 °C (32.0~482.0 °F)
●Display unit : 1 °C (°F)
Fuel meter
●Display range : 6 levels
●Display unit : 1 level(16.6 %)
Max. speed record
●Display range : 0 ~360 km/h (0 ~225 MPH)
●Display unit : 1 km/h (MPH)
Max. Gear record
●Display range : -, N, 1~the highest gear
Max. RPM record
●Display range : 0~10,000 RPM / 0~15,000 RPM
●Display unit : 111 RPM / 166 RPM
Max. temperature record
●Display range : 0.0~250.0 °C (32.0~482.0 °F)
●Display unit : 0.1 °C (°F)
EX. 4 Rear disc - detect the gap between the disc.
After installation, use your hand to turn the tire to see if everything is ok. The LED on the active speed sensor will light up
once the signal is detected.
EX. 1
The active speed sensor could be facing the metal parts to detect the speed.
EX. 1 The disc screw.
EX. 2 The disc to detect the disc gap. (Make sure the distances between the gaps are the same in advance to avoid wrong
speed signal.)
EX. 3 The sprocket to detect the disc gap. (Make sure the distances between the gaps are the same in advance to avoid wrong
speed signal.)
We will suggest you to catch the speed from the disc screws. The more the sensor points are, the better the speed accuracy is. The
maximum sensor points the speed sensor could detect is 40 points per turn.
speed
sensor
speed
sensor
the detect range
speed
sensor
speed
sensor speed
sensor
the detect range
speed sensor speed sensor
the detect range
speed sensor speed sensor
the detect range
EX. 2,4 EX. 3
The hexagon socket disc screw
The best detect area:The edge of
the hexagon socket screw.
Don't pick-up the signal from
the middle hole of the hexagon
socket screw to avoid wrong signal.
The hexagon screw
The best detect area:The middle
of the screws.
Some hexagon screw center is with a small
hole in the center in this case,we will suggest
you to catch the signal from the edge of the
screw like the hexagon socket screw.
The disc
The best detection area:Detect
the speed signal from the gaps of the disc.
Note that there are discs with
the gaps in different difference, and
this method will not work on it.
The sprocket
The best detect area:Detect the
speed signal from the gaps of the sprocket.
Note that there are sprockets
with the gaps in different difference,
and this method will not work on it.
3-1 Meter Size
96 mm
53 mm
17 25 11
Front Back Side

wh077ba07a(P15-5)
●Speedometer Display range : 0 ~360 km/h (0 ~225 MPH)
Display unit : 1 km/h (MPH) Switchable
○ Max. speed record Display range : 0 ~360 km/h (0 ~225 MPH),
can return to zero manually
Display unit : 1 km/h (MPH)
○Odometer Setting range : 0 ~99,999 km (mile)
●Motor oil maintenance
(Trip O)
Display range : OFF, -999~16,000 km
(-999~10,000 mile), can be reset manually
Display unit : 1 km (mile)
○ Motor oil maintenance
warning
Setting range : OFF, 500 ~ 16,000 km(300~10,000 mile)
When lower than 0 km (mile), the value shows on the
screen and flickers for warning, and the warning signal
will be lit according to the setting.
Setting unit : 100 km(mile)
○Trip meter A, B
Setting unit : 1 km (mile)
● Gear Meter Display range : OFF, -, N, 1~the highest gear
○Max. Gear record Display range : - , N,1~the highest gear,
can return to zero manually
●Tachometer Display range : 0~10,000 RPM / 0~15,000 RPM
Display unit : 111 RPM / 166 RPM
○Shift light warning
○Max. RPM record
● Temperature Display range : 0.0~250.0 °C (32.0~482.0 °F)
Display unit : 0.1 °C (°F)
Setting range : 1,000~10,000 RPM / 0~15,000 RPM,
When exceeding the set value (inclusive), the warning
signal will be lit according to the setting.
Setting unit : 100 RPM
Setting unit : 1 km/h (MPH)
Setting range : 30~360 km/h (19~225 MPH),When
exceeding the set value (inclusive), the value flickers
and the warning signal will be lit according to the setting.
○ Speeding warning
setting
Display range : 0.0~9,999.9 km (mile), can
return to zero manually
Display unit : 0.1 km (mile)
Specifications
3-3
Setting range : 60~250 °C(140~482 °F), When
exceeding the set warning value, the value flickers,
and the warning signal will be lit according to the setting.
Setting unit : 1 °C (°F)
○ Overheat warning
setting
Check engine light (Amber)
High beam light (Blue)
Neutral light (Green)
Warning light (Red)
ABS light (Amber)
Turn signal light (Green)
Over-running light (Red)
●Indicator
●Operating temperature -20~ 85 °C
○Storage temperature -30~ 90 °C
● Specification JIS D 0203 (S2)
● Meter Size D 96 mm
● Meter Weight About 184 g
○Operating voltage DC 12V
NOTE
Design and specifications are subject to change without notice.
● Fuel meter Display range : 6 levels
Display unit : 1 level(16.6 %)
○Low voltage warning
● Voltmeter Display range : DC 8.0 ~ 18.0 V
Display unit : DC 0.1 V
●Clock Setting range : 00:00~23:59 (24H)
01:00~12:59 (12H)
● Backlight brightness
● Unit Speed unit : km/h , MPH
Temperature unit : ˚C (Celsius) and ˚F (Fahrenheit)
○Max. temperature
record
Display range : 0.0~250.0 °C (32.0~482.0 °F) ,
can return to zero manually
Display unit : 0.1 °C (°F)
Setting range : DC 8.0~13.0 V, When lower than the set
warning value for over five seconds, the value flickers,
and the warning signal will be lit according to the setting.
Setting unit : DC 0.1 V
Setting range : 1/5 (darkest)~ 5/5 (brightest)
Setting unit : 1/5(20%)
●Circumference
Setting unit : 1 mm
Setting range : 300~2,500 mm
○ Sensitive point
Setting unit : 1 P
Setting range : 1~20 P
Display range : 1,000~10,000 RPM / 0~15,000 RPM,
can return to zero manually.
Display unit : 111 RPM / 166 RPM
● Fuel resistance
○ Fuel warning setting
Setting range : 100 Ω, 250 Ω, 270 Ω, 390 Ω
510 Ω, 1200 Ω, Switch, Custom ,OFF
Setting range : 0 ~ 3/6 grid
Setting unit : 1 grid
Size,Specifications(Meter External Switch)
3-4
43.7 mm
Ø25.4 mm
14.7 mm
41.3 mm
32 mm
NOTE
Design and specifications are subject to change without notice.
○Storage temperature
●Effective voltage
●Standard
●Weight
●Size
-30~ 90 °C
●Operating temperature
-20~ 85 °C
JIS D 0203
DC 8 ~ 32V / Max. 50 mA / 1.6W
About
43.7 x 41.3 x 14.7 mm
About 39 g
Meter external switch (Accessory 8) is suitable for 22.2 mm (7/8'') &
25.4 mm (1") handlebar.
NOTE
Up button
Down button

wh077ba08a(P15-6)
●In the total mileage screen.
Main Menu Switching Description (including the warning screen)-Up button
4-1
●In the fuel screen, press the Down button to go back
to the total temperature screen.
●In the temperature screen, press the Down button to
switch to the fuel screen.
●In the temperature screen.
Main Menu Switching Description-Down button
4-2
●In the total mileage screen, press the Up button
to enter the TRIP A screen.
●In the total mileage screen, press the Up button
for 3 seconds to enter the setting screen.
When a warning occurs, press the Up button
to shift to the warning screen.
NOTE
●In the Motor oil warning screen, press the Up
button to enter the TRIP A screen.
A warning will only show on the screen
when it occurs.
NOTE
When no warning occurs
●In the TRIP A screen, press the Up button to enter
theTRIP B screen.
●Press the Up button for 3 seconds to reset
Trip A record.
●Press the Up button for 3 seconds to reset
Trip B record.
●In the TRIP B screen, press the Up button to enter
theTRIP O screen.
●Press the Up button for 8 seconds
to reset Trip O record.
●In the TRIP O screen, press the Up button
to enter the Max. record screen.
●Press the Up button for 3 seconds
to reset Max. record screen.
●In the Max. record screen, press the
Up button to go back to the total
mileage screen.

wh077ba07a(P15-7)
❻RPM input pulse,
Signal impulse,RPM range ❺Gear ❹Tire circumference,Sensor point ❸Backlight(Brightness)
❶Clock ❷Unit(Speed/Temperature)
●Main screen(ODO) ●Enter the setting screen.
⓯ABS warning ⓰Internal and External ODO ⓱Exit
⓫Fuel warning⓮Warning light warning ⓭Motor oil maintenance ⓬Voltage warning
❼Fuel resistance ❽Speeding warning ❾Shift light warning ❿Overheat warning
Setting Screen Switching Description
5
●Press the Up button for 3 seconds on the main screen(ODO) to switch to the setting screen.
●Press the Up button or Down button to select
❶Clock ❷Unit(Speed/Temperature) ❸Backlight(Brightness) ❹Tire circumference,Sensor point ❺Gear ❻RPM input pulse, Signal impulse,RPM range
❼Fuel resistance ❽Speeding warning ❾Shift light warning ❿Overheat warning ⓫Fuel warning ⓬Voltage warning⓭Motor oil maintenance
⓮Warning light warning ⓯ABS warning ⓰Internal and External ODO ⓱Exit
NOTE During setting, if any button is not pressed for 30 seconds, it will automatically return to the startup screen.

wh077ba07a(P15-8)
5-1
Clock Setting
●The Clock screen, press the Down
button for 3 seconds to enter the
Clock setting.
●EX : Set time format from 24 H to 12 H.
●Press the Down button to enter time
adjustment hour setting.
●EX : Set hour from 12:00 AM to 10:00 AM.
●Press the Down button to enter clock
adjustment minute setting.
●Press the Down button to move to the
digit you want to set.
●Example : To set clock(minute) as
10 minutes.
●Example : Changing to 12H.
●Press the Up button to choose
the setting option.
Now the setting value is flashing.
Setting range : 12 H, 24 H.
Default value : 24 H.
NOTE
●Example : To set clock(hour) to 10 hours.
●Press the Up button to choose
the setting number.
Now the setting value is flashing.
Setting range : 1~12(12H)
0 ~23(24H)
Default value : 12(12H)/0(24H)
Cursor moving order is :
Hour →Digit in ten minutes →
Digit in minutes
NOTE
NOTE
●Press the Up button to choose the
setting number.
●EX : Set minute from 0 minutes to
10 minutes.
●Press the Down button to go back to
the Clock screen.
●The Clock screen.
Now the setting value is flashing.
Setting range : 00~59 minutes.
Default value : 0.
NOTE
5-2
Unit (Speed,Temperature) Setting
●The unit screen, press the Down button
for 3 seconds to enter the speed unit
setting.
●EX : Set speed unit from km/h to MPH.
●Press the Down button to enter the
temp. unit setting screen.
●EX : Set temp. unit from ˚C (Celsius)
to ˚F (Fahrenheit).
●Press the Down button to go back to
the unit screen.
●The unit screen.
●Example : To set speed unit in MPH.
●Press the Up button to choose
the setting options.
Now the setting value is flashing.
NOTE Setting range : km/h, MPH.
Default value : km/h .
●Example : To set temp. unit to ˚F.
●Press the Up button to choose
the setting options.
Now the setting value is flashing.
NOTE Setting range : ˚C (Celsius) and
˚F (Fahrenheit).
Default value : ˚C (Celsius).

wh077ba07a(P15-9)
5-4
Tire Circumference and sensor point setting
●Press the Up button to choose
the setting number.
●EX : Set the tire circumference value
from 1,000 mm to 1,300 mm .
●Press the Down button to enter the
sensor point setting.
●Press the Up button to choose
the setting number.
●The tire circumference and sensor
point screen
When mile is set for the unit,
ride for 1 mile.
NOTE
●Press the Up button to start the
learning mode.
●EX : Set the sensor point value from
01 P to 06 P.
●Press the Down button to enter the
learning mode setting.
●Ride for 1 km(1 mile); after the
arrival, press the Down button.
Complete learning by return to the tire
circumference and sensor point screen.
●Press the Up button to cancel learning.
●When’’Over!’’ is displayed, the value
detected is excessive, exceeding the
setting scope.
●When’’Short!’’ is displayed, the value
detected is insufficient, lower than the
setting scope.
5-3
Backlight(Brightness) Setting
●The backlight screen, press the Down
button for 3 seconds to enter the
backlight setting.
●The backlight screen
●EX : The backlight brightness setting is
changed from 3/5 (60%) to 2/5 (40%).
●Press the Down button to go back to
the backlight screen.
●Example : To set the backlight
brightness to 2/5(40%).
●Press the Up button to choose
the setting number.
Now the setting value is flashing.
NOTE Setting range :
1/5 (Darkest)~ 5/5 (Brightest).
Setting unit : 20% per level.
Default value : 3/5(60%).
NOTE The backlight brightness will
change immediately after
you set the value.
●You can use the tire
valve as the starting
point and the terminal
point to measure the
wheel circumference
with a measuring tape.
●Example : To set the sensor point
value to 06 P .
●Press the Down button to move to the
digit you want to set.
Setting range : 01 P~20 P.
Default value : 01 P.
Now the setting value is flashing.
NOTE
●The tire circumference and sensor
point screen, press the Down button
for 3 seconds to enter the tire
circumference and sensor point setting.
Reset this setting value if you
change to a different tire size.
●Measure the tire circumference (The tire
you will install the sensor on) and make
sure the number of sensor points.
●The speed displayed on the meter will
be affected by the setting, make
sure the setting number is correct before
you enter the setting.
CAUTION!
●Example : If the tire circumference is
1,300 mm.
●Press the Down button to move to the
digit you want to set.
Setting range : 300~2,500 mm.
Default value : 1,000 mm.
Now the setting value is flashing.
NOTE

wh077ba07a(P15-10)
5-5
Gear Setting
●The gear screen, press the Down button
for 3 seconds to enter the gear setting.
●EX : Set the gear setting to ON.
●Press the Down button to enter the
gear-learning setting screen.
●Example : You want to set the gear
setting to ON.
●Press the Up button to choose
the setting options.
Setting range : ON, OFF.
Default value : ON.
Now the setting value is flashing.
NOTE
Select OFF to return to the
gear screen.
NOTE
OFF
●Press the Up button to start the
gear-learning setting.
●Press the Down button to go back to
the The gear screen.
Enter the Learning Mode, and
learn the Gear position according
to the speed and RPM.
NOTE
●When N→1 appears, change
to Gear 1 to ride.When Gear 1 is
detected, 1→2 appears and then
change to Gear 2.
●In the gear-learning setting.
Before setting, be sure to put your motor
in Neutral to avoid error detection.
CAUTION!
"Fail"on the screen means error detection,
re-set Gear-Learn.
CAUTION!
If gear learning is not required, press
Up button to cancel the gear learning.
CAUTION!
P.S.
●During actual gear level learning, select road that is wide
and has more straight distance with no traffic lights for more
accurate settings and traffic safety.
●After reaching and finishing Gear 6,
when 6→7 is displayed, wait for a few
seconds to end gear-learning and return
to the gear screen.
●The gear screen.
NOTE Press the Up button to quit the
learning and return to the main
screen.
○Change to Gear 2.
○Change to Gear 3.
○Change to Gear 4.
○Change to Gear 5.
○Change to Gear 6.
5-6
RPM input pulse & Signal impulse & RPM range
●The RPM input pulse & signal impulse
& RPM range screen, press the Down
button for 3 seconds to enter the
RPM input pulse & signal impulse &
RPM range setting.
●EX : Set the signal impulse from
High-Act to Low-Act.
●Press the Down button to enter
the RPM range screen.
●EX : The RPM input pulse setting is
changed from1.0 to 2.0.
●Press the Down button to enter the
signal impulse setting.
●Example : You want to set the RPM
input pulse to 2 (4 Stroke, 4 piston).
●Press the Up button to choose
the setting number.
Setting range : P-0.5, 1.0~24.0.
Default value : 1.0.
Now the setting value is flashing.
NOTE
Most of the 4-cycle bikes with one single
piston are igniting once every360 degree,
so the setting should be the same as the
bike with 2-cycle and one piston engine.
CAUTION!
2C-1P 4C-2P
4C-4P2C-2P
0.5
2.0
4C-6P2C-3P3.0
4C-8P2C-4P4.0
4C-10P5.0
4C-12P2C-6P6.0
1.0
4C-1P
The
setting
value
The corresponding RPM signal
number per ignition.
The correspond-
ing stroke and
pistons number.
2 RPM signals per 1 ignition.
1 RPM signal per 1 ignition.
1 RPM signal per 2 ignition.
1 RPM signal per 3 ignition.
1 RPM signal per 4 ignition.
1 RPM signal per 5 ignition.
1 RPM signal per 6 ignition.
●Example : Set the signal impulse to
Low-Act.
●Press the Up button to choose the
setting options.
Setting range :High-Act, Low-Act.
Default value : High-Act.
Now the setting value is flashing!
NOTE