Koso 10032697 User manual

ACHTUNG!DE Verbrennungsgefahr. Die Heizgriffe können sehr hohe Temperaturen erreichen.
Die Heizgriffe dürfen nur mit geeignetem Schutz für die Hände verwendet werden.
Level 1 Temperature Curve
Level 2 Temperature Curve
Level 3 Temperature Curve
Level 4 Temperature Curve
Level 5 Temperature Curve
5
Bar-end cap X2
3-2 Wiring installation instructions
Accessories1
wh04ax008c
個
2
Ring Fixed Switch X1
31
Heated grip X2
4
M4x6xP0.7
Hexagon Socket Screw X1
Connecting wire X1
使用說明書 3-1 Practical installation instruction
Heated grip testing data
2-2
Specifications
2-1
●
Ring Fixed Switch (Accessory 2)
Connecting wire (Accessory 3)
Black / Ground wire connects to the engine or
to the negative pole of the battery.
Red / Positive wire connecting
to the key on switch (DC 12 V)
Heated grip (Accessory 1)
❶Ring Fixed Switch (Accessory 2)
❷M4 Hexagon Socket Screw (Accessory 4)
❶
❷1.2 Nm (12 kgf.cm)
Follow the steps below during installation.
1. Use an appropriate tool to
remove the original handle-bar
grips.
2. Apply a cleaning agent and
wipe back and forth to remove
the glue residue from the
handlebar.
3. Please use an appropriate
tool to affix the ring fixed switch
(Accessory 2) to the handle.
Please adjust the angle during the
installation to prevent interfering
the button.
Figure 1
1.
5. To install the side cap
(Accessory 5) onto the
heating grip, insert the top
cap into the top groove and
then press it downward into
the bottom groove.
2.
Need to keep a small distance To install the heating grip
(Accessory 1) onto the throttle
sleeve, the throttle must
maintain a small distance with
a surplus distance for wiring;
You must test them by rotating
back and forth to make sure
they can twist.
Figure 5
Figure 6
4. Push the heated grip
(Accessory 1) straight onto
the handlebar.
If the heated grip is not
fastened firmly enough to
the handlebars, apply a
little heated grip adhesive
(sold separately) to
prevent it from twisting
whilst on the road.
Figure 3
Figure 2
Figure 4 To install, do not use any tool to
knock the grip on direct. Do not
twist the grip by hand or with a
tool.By doing so, this will break
or damage the wire inside the
handlebar.
Contact your local distributor if the items received in the box are not the same as the one listed above.
PRESS THE
BUTTON
ONCE
FLASH LIGHT ON
PRESS THE
BUTTON 3
SECONDS
Thank you for purchasing our product. Before installing, please read the instruction carefully and keep it for future reference.
Attention!
Some processes must be followed to avoid the affection caused by wrong installation .
You could get the installation details from the information behind the mark.
Certain procedure must be followed to avoid damages to the vehicle.
For installation, follow the steps on the instruction sheet. Any damage caused by falty installation shall be imputed to the users.
●
Don't break or modify the wires. To avoid a short circuit, do not pull the wires out of the terminals during installing.
●
Do not disassemble, alter or change any parts.
●
Maintenance or repairs should be executed by our professionals.
●
◎MARK MEANING:
Certain procedure must be followed to avoid damages to yourself or the public.
●Voltage
● Switch size
DC 12 V
W57.9 X L8.65 X H57.6 mm
● Light Signal Stage 1 [Blue]
Stage 2 [Green]
Stage 3 [Yellow]
●Water-Proof Standard JIS D 0203
●Fuse type 4A (ASP)
●Heating stage Stage 1 (low) ~ Stage 5 (high)
● Switch weight (with wire) About 39 g
Stage 4 [Orange]
Stage 5 [Red]
Design and specifications are subject to change without notice!
57.9 mm
8.65 mm
22.7 mm
57.6 mm
0
0
20
40
60
80
100
120
510 15 20 25 30 (Minuten)
(℃)
Durchführung der Tsets bei einer Umgebung stemperatur von unter 26 °C miteiner Betriebsspannung von 13,5 V.
HINWEIS Atención!ES Riesgo de quemaduras. Los puños calefactables pueden alcanzar temperaturas muy elevadas.
Los puños calefactables deben utilizarse únicamente en combinación con una protección adecuada para las manos.
Attention!FR Risque de brûlure! Les poignées chauffantes peuvent atteindre des températures très élevées.
Les poignées chauffantes doivent uniquement être utilisées avec une protection adaptée pour les mains.
Attenzione!IT Rischio di ustioni! Le manopole riscaldate possono raggiungere temperature molto elevate.
È consentito utilizzare le manopole riscaldate solo con una protezione per le mani adatta.
Pas op!NL Gevaar voor brandwonden! De verwarmde handvaten kunnen zeer hoge temperaturen bereiken.
De verwarmde handvaten mogen alleen met een geschikte handbescherming worden gebruikt.
Risk of burns! The heated grips can reach very high temperatures. The heated grips may only be used with suitable
hand protection.
Caution!EN

Light Signal List :
Heat up stage Voltage
11.1 ~ 11.5 V
11.6 ~ 12.0 V
12.1 ~ 12.5 V
Blue ( Stage 1)
Green
( Stage 2)
Yellow
( Stage 3)
Orange
( Stage 4)
Red
( Stage 5)
Below 11.0 V
Over 12.6 V
Blue
Green
Yellow
Orange
Red
Function setting instruction
4-1
Low-voltage mode Description
4-2
● Standby mode will be enabled when the voltage over 11.5 V is restored.
The LED would show lightings in the
direction from blue light to red light
at this moment.
● Key on,enter the power pressure
detecting mode.
The heat up will begin with red LED
light (stage 5) upon entering the heat
up mode.
When the button remained idle for 5
seconds, the stage shifting will start
from red LED light (stage 5) after
pressing the button.
● Press the button, then select your
desired value.
● EX：The heat up stage was adjusted
from stage 5 to stage 3.
● EX：The heat up stage is stage 3
heat up.
● Standby mode, press the button once
to enter into the heating mode.
● The corresponding light signal
would be shown according to the
power pressure detected.
At this moment , LED flashes , it will shift back to standby mode after 10 seconds.
● The heating system will be turned off automatically when the voltage is lower than 11.5 V.
Stage 5(high)→Stage 4→Stage 3
→Stage 2→Stage 1(low)→OFF.
After starting the grip, the heat
up function will net commenced
without pressing the button.
Trouble shooting
5
The following situation do not indicate malfunction of the meter.Please check the following points,before taking it in for repair.
Trouble
LED indication does not activate. Power supply cable disconnected.
→Please check if power supply
cable is broken or disconnected.
→Please check if positive and
negative poles are properly
connected.
Check item Trouble Check item
When turn the key on , the
headed grip is not heating up.
●
It might be the fuse blown out.
→Please check if the fuse is in
normal state.
●
It might be the battery is
running out.
→ Please check your battery
voltage as soon as possible.
●
It might be causing by no power
supply.
→ Please check if power harness
and fuse broken or disconnected.
→ Please check if positive pole
and negative pole is well
connected.
●
When the corresponding power
pressure is shown, the light
would flicker three times.
wh04ax008c