Kramer 617T User manual

Installation Instructions
MODELS:
617T, 617R
4K HDR HDMI Tx/Rx over Extended-Reach
Multi-Mode Fiber Optic Cable
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where
updates to this user manual may befound.
We welcome your questions, comments, andfeedback.
www.KramerAV.com
[e-mail]
P/N:
2900-301021
Rev:
2
All manuals and user guides at all-guides.com
all-guides.com

617T, 617R 4K HDR HDMI Tx/Rx over Extended-Reach Multi-Mode Fiber
Optic Cable
Congratulations on purchasing your Kramer 617T and 617R Plug and Play active 4K HDR HDMI
Tx/Rx over Extended-Reach Multi-Mode (MM) Fiber Optic cable. 617T and 617R extend signals of up
to 4096x2160 @60Hz (4:4:4), over a distance of up to 200m (656ft) without signal scaling or data
compression, providing a maximum data rate of 18Gbps. 617T and 617R are easily and securely
connected via a 2LC fiber connector and can be powered from the USB connector. Alternatively, 617T
only can be powered from the HDMI interface (pin #18).
Figure 1: 617T Transmitter and 617R Receiver
Safety
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
Warning:
Avoid direct eye exposure into the optic connectors when powered,
although this product is regulated strictly enough to operate under the
Laser Class 3R for eye safety.
See www.KramerAV.com for updated safety information.
Installation
To install 617T and 617R:
1. Unpack the contents of the package with care.
We recommend that you save the original box and packaging materials for possible future
shipment.
2. Turn on the power to the HDMI source (for example, a laptop) and acceptor (for example, a
display).
3. Power the 617T and 617R:
•Connect the micro USB connector on each device to a USB cable (supplied).
•Connect the USB cable either to the wall-mount power adapter (supplied) and to the
mains, or to a USB port.
The POWER LED lights and the STATUS LED flashes three times.
Although 617T can be powered via pin #18 on the HDMI interface, we
recommend that you use the USB power adapter.
617R can only be powered via the USB power adapter.
All manuals and user guides at all-guides.com

4. Connect the two LC optical fibers between 617T and 617R.
Connect (A) to (A) and (B) to (B). Make sure that the duplex connectors are connected
properly.
The STATUS LED flashes.
Do not look directly into the LC connectors on the 617T (the transmitter side)
when it’s powered.
This product operates under LASER Class I, classified by CDRH/FDA for eye
safety.
We recommend that you avoid using intermediate cables or adapters. Using
them may affect the transmission quality.
5. Connect 617T to the HDMI connector on the source side and 617R on the acceptor side.
Make sure that the 617T is always connected to the source side and the
617R is connected to the acceptor side.
Once the system is connected the Status LEDs on both 617T and 617R flash.
Troubleshooting
If the display appears black:
•Check that the power source adapters are properly connected on both sides.
•Check that both HDMI connector heads are fully plugged into the devices.
•Check that the source and display devices are both switched on.
•Reset the system by disconnecting and then reconnecting the 617T or 617R, or by
disconnecting and then reconnecting the power adapters.
•Reboot the system.
All manuals and user guides at all-guides.com

If the image appears distorted and/or there is background noise:
•Go to the display properties and check the settings. Make sure that the resolution is set below
4096x2160 at a 60Hz refresh ratio to check if the graphic resolution is properly defined.
•Reset the system by disconnecting and then reconnecting the 617T or 617R, or by
disconnecting and then reconnecting the power adapters.
It is important to connect the devices correctly as marked: 617T to the source side and
617R to the acceptor side.
Specifications
Video
Max. Resolution
4K @60Hz 4:4:4 (4096x2160)
Data Rate
Maximum 6 Gbps per channel
Compliance
Supports HDMI 2.0, HDCP 2.2, EDID and CEC
Ports
617T (source end)
Male HDMI connector
617R (display end)
Male HDMI connector
617T (source end)
Micro USB (for power supply)
617R (display end)
Micro USB (for power supply)
Power
5V
Via USB source
Via external source
From HDMI PIN #18 (617T only)
Consumption
<2.5W
Recommended
Cable
Structure
Dual Multi-mode OM3 (50/125um) glass fiber
Optical Connectors
Duplex LC connectors
Max. Fiber Cable Attenuation
(λ=850nm)
2.5dB/KM
Max. Skew
0.4ns
Max. Insertion Attenuation
0.5dB
Total Optical Attenuation
1dB max @ 656ft/200m extension
Maximum Length
200m (656ft)
Environmental
Conditions
Operating Temperature
0° to +50°C (32° to 122°F)
Storage Temperature
-30° to +70°C (-22° to 158°F)
Operating Humidity
0 to 85%
Standard
Compliance
CE
EN 55032:2012/AC: 2013 (Class A),
EN 61000-3-2:2014, EN 61000-3-3:2013,
EN 55024:2010
FCC
CFR 47 part 15 SUBPART B Class B, Section
15.101
Environmental
RoHS (2011/65/ EU)
General
Net Dimensions (W, D, H), each
2.6cm x 7.2cm x 1.5cm
(1" x 2.8" x 0.6")
Shipping Dimensions (W, D, H)
19.3cm x 25.3cm x 62cm
(7.6" x 10" x 24.4")
Net Weight, each
0.12kg (0.3bs) approx.
Shipping Weight
1.48kg (3.3lbs) approx.
Accessories
Included
2 Micro USB to USB type-A cables, 2 Wall-mount
power adaptors
All manuals and user guides at all-guides.com