Kramer VM-2DT User manual

VM
-2DT Quick Start (P/N: 2900-300363QS REV 1)
P/N:
2900- 300363QS
Rev:
1
Scan for full manual
VM-2DT Quick Start Guide
This guide helps you install and use your VM-2DT for the first time.
Go to www.kramerav.com/downloads/VM-2DT to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
VM-2DT
1:2 HDBT Distributor 1 Power supply (5V DC)
TOOL Mounting bracket kit
4 Rubber feet 1 Quick start guide
Step 2: Get to know your VM-2DT
# Feature Function
1 PROGRAM Mini USB Connector Use to send RS-232 commands. Connect to a PC to perform firmware upgrades (via
K-Upload) and work with the EDID Designer. K-Upload and EDID Designer can be
downloaded from our Web site at:www.kramerav.com/manual/EDID Designer
2
EDID SETUP Button
Press to capture the input EDID, force RGB mode or select the default EDID
3
ACTIVE INPUT LED
Lights green when an active input signal is detected
4 HDBT LINK LEDs IN Lights green when a link is established with the HDBaseT transmitter
OUT Lights green when a link is established with the HDBaseT receiver (1 and 2)
5
OUTPUTS CONNECTED LEDs
Lights green when an active output acceptor is detected (1 and 2)
6
ON LED
Lights green when the unit receives power
7 INPUT HDBT Connector Connects to an HDBaseT source, for example
VS-44DT
8 HDBT OUT Connectors Connect to an HDBaseT acceptor (from 1 to 2), for example TP-580R
9 SETUP 8-way DIP-switches Use to set the IR (DIP-switches 1 and 2) and RS-232 (DIP-switches 5 and 6)
commands behavior
10
SETUP 4-way DIP-switch
For future use
11 5V DC +5V DC connector for powering the unit
Step 3: Install the VM-2DT
To mount the VM-2DT in a rack, use an RK-T2B rack adapter. Alternatively, attach the rubber feet to the underside of the VM-2DT
and place it on a table.
A Kramer Mega TOOLS™ can also be mounted on a desk top, wall or similar area. Fasten a bracket on each side of the TOOLS
using the two M3x8 screws (supplied). Use the flat-head screws (supplied) to fix the TOOLS to the mounting surface or enable it to
slide in place.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VM-2DT. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VM-2DT.
RJ-45 Pinout:
DIP-Switch Setup:
For the HDBaseT connectors, see the wiring
diagram below:
PIN EIA /TIA 568B
PIN Wire Color
1 Orange / White
2
Orange
3 Green / White
4 Blue
5 Blue / White Out # IR Routing is enabled when: RS-232 Routing is enabled when:
6 Green OUT 1 DIP 1 – OFF (up) DIP 5 – OFF (up)
7 Brown / White OUT 2 DIP 2 – OFF (up) DIP 6 – OFF (up)
DIP-Switches 3, 4, 7 and 8 are reserved for future use.
Step 5: Connect the power
Connect the power adapter to the VM-2DT and plug the adapter into the mains electricity.
Step 6: Acquire the EDID
To acquire an EDID, press the EDID SETUP button as follows:
1. Press the EDID SETUP button once.
The OUTPUTS CONNECTED LEDs flash to indicate the current EDID used: 1 or 2, or both if the default EDID is currently used.
2. Press the EDID SETUP button again to enter the EDID read mode and then press repeatedely to cycle through the EDID source
options until the desired EDID source is reached: OUT 1 -> OUT 2 -> both LEDs flash (for a default EDID).
3. Wait a few seconds for the VM-2DT to read the EDID.
When complete, all LEDs return to display the present output connection status.
Technical Specifications
Input:
1 HDBT connector
Outputs:
2 HDBT connectors
Max. Resolution:
4K@60Hz 4:2:0
Max. Data Rate:
10.2Gbps (3.4Gbps per graphic channel)
Compliance:
Supports HDMI 2.0 and HDCP 1.4
Controls:
EDID Setup button; Indicator LEDS: OUTPUTS 1 and 2, LINK 1 and 2, active input, power on
Operating Conditions: Operating Temperature: 0° to +40°C (32° to 104°F); Storage Temperature: -40° to +70°C (-40° to
158°F); Humidity: 10% to 90%, RHL non-condensing
Power:
Power Source: 5.2V/4A; Power Consumption: 5V DC, 2.5A
Dimensions (W, D, H):
18.8 x 11.5 x 2.54cm (7.4 x 4.53 x 1"); Shipping Dimensions: 34.5 x 16.5 x 5.2 (13.6 x 6.5 x 2.05")
Weight:
0.53kg (1.17lb); Shipping Weight: 1.29kg (2.84lb)
Included Accessories:
Power supply
Options:
RK-T2B 19” rack adapter, Kramer HDBT cables
Specifications are subject to change without notice at www.kramerav.com