Kramer VP-426C User manual

VP-426C Quick Start (P/N: 2900-3010055QS REV 1)
P/N:
2900- 301055QS
Rev:
1
Scan for full manual
VP-426C Quick Start Guide
This guide helps you install and use your VP-426C for the first time.
Go to www.kramerav.com/downloads/VP-426C to download the latest user manual and checkif firmware
upgrades are available.
Step 1: Check what’s in the box
VP-426C 4K HDMI/USB-C/PC Scaler
1 Bracket set
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your VP-426C
#
Feature
Function
1
ON LED
Lights green when the unit is powered.
2
INPUT Button
Press to cycle the input between HDMI, USB-C and PC.
3
HDMI™LED
Lights when the HDMI input is selected.
4
USB-C LED
Lights when the USB-C input is selected.
5
PC LED
Lights when the PC input is selected.
6
MENU Button
Press to enter/escape the on-screen display (OSD) menu. Press together with
the –button to reset to 1080p (RESET TO 1080P).
7
ENTER Button
In OSD, press to choose the highlighted menu item. Press together with the
+ button to reset to XGA (RESET TO XGA).
8
–Button
In OSD, press to move backward through the list or to decrement the
parameter value.
9
+/FREEZE Button
In OSD, press to move forward through the list or to increment the parameter
value. When not in OSD, press to freeze the display.
10
PROG USB Connector
Connect to a PC for upgrading the firmware.
11
AUDIO IN PC 3.5mm Mini Jack
Connect to an unbalanced stereo audio PC source. Can also be selected as
the audio input (instead of the HDMI and USB-C embedded audio inputs).
12
PC IN 15-pin HD Connector
Connect to a laptop.
13
USB-C IN USB Type C Port
Connect to a USB type-C audio-video source.
14
HDMI™ IN Connector
Connect to an HDMI source.
15
HDMI™OUT Connector
Connect to an HDMI acceptor.
16
AUDIO OUT Terminal Block Connector
Connect to a balanced stereo audio acceptor.
17
REMOTE 4-pin Terminal Block Connector
Connect to contact closure switches (by momentary contact between the
desired pin and GND pin) to select an input.
18
5V DC
+5V DC connector for powering the unit.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Install the VP-426C
Install VP-426C using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/VP-426C.
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/VP-426C).
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-426C. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VP-426C.
Connect the audio output
To a balanced
stereo audio
acceptor:
To an
unbalanced
stereo audio
acceptor:
Step 5: Connect the power
Connect the power cord to VP-426C and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Warning:
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information
Step 6: Operate and control the VP-426C
Select the input via the following options:
•Press the front panel INPUT button.
•Use the contact closure terminal block to select an input remotely with the
press of a button.
Press the MENU button to configure and control the device via OSD menu:
•Set brightness, contrast, color, noise reduction etc.
•Manage EDID.
•Configure HDCP behavior.
•Select resolution and aspect ratio.
•Manage auto power down (Auto Sync Off).
•Manage audio bypass and delay.
•View device information.
•Reset to factory default parameters.
•Control OSD display.