Kramer FC-101Net User manual

FC‑101NET Quick Start
P/N:
2900- 300861QS
Rev:
2
Scan for full manual
FC‑101NET Quick Start Guide
This guide helps you install and use your FC‑101NET for the first time.
Go to www.kramerav.com/downloads/FC-101NET to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
FC‑101NET Dual Dante Interface
1 Bracket set
Double-sided adhesive dual lock tape
1 Quick start guide
Step 2: Get to know your FC‑101NET
#
Feature
Function
1
ON LED
Lights green when the device receives power.
2
SYS LED
Lights green when Dante network is available; red if an error has occurred.
3
SYNC LED
Lights green for digital audio normal operation.
Flashes green when this unit is the Master clock.
Lights red if an error has occurred.
4
Dante PoE RJ-45 Port
Connect to the Dante audio source via the Network and provide Power over Ethernet
(PoE) to the device.
By default, DHCP is enabled.
5
DEF Push Button
To reset/reboot the device, press and release the button.
To reset to factory settings, press and hold the button for 30 seconds.
6
OUTPUTS 1 and 2 5-pin Terminal
Block Connector
Connect to a single balanced stereo audio output or two separate mono outputs
(+, –, G).
7
RS-232 3-pin Terminal Block
Connector
Connect to a serial controller to control this device.
Step 3: Install FC‑101NET
Install FC‑101NET using one of the following methods:
Attach one side of the adhesive dual lock tape to the metallic surface of the device and the
other to a flat surface.
Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more
information go to www.kramerav.com/downloads/FC-101NET.
Mount the unit in a rack using an optional RK-4PT rack adapter.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your FC‑101NET. For best results, we recommend that
you always use Kramer high-performance cables to connect AV equipment to FC‑101NET.
Step 5: Connect the power
Once connected, PoE is provided via the Dante port.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Disconnect the power before installing.
See www.KramerAV.com for updated safety information.
Step 6: Operate FC‑101NET
Operate FC‑101NET via:
Remotely, RS-232 serial commands
transmitted by a touch screen system, PC, or
other serial controller.
RS-232
Baud Rate:
115200
Parity:
None
Stop Bits:
1
Data Bits:
8
Command Format:
ASCII
Example: (set the volume output to -6dB): #AUD-LVL 2,1,-6<CR>
Technical Specifications
Outputs
1 Balanced Stereo Audio/2 Mono
Audio
On a 5-pin terminal block
Port
1 Dante
On an RJ-45 connector
Control
Dante IP control matrix and Kramer Protocol
3000
Power
Consumption
48V DC, 100mA
Source
48V DC (PoE)
Cooling
Convection Ventilation
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory Compliance
Safety
CE
Environmental
RoHs, WEEE
Enclosure
Size
Pico TOOL
Type
Aluminum
General
Net Dimensions (W, D, H)
6.2cm x 5.2cm x 2.4cm (2.4” x 2” x 1”) W, D, H
Shipping Dimensions (W, D, H)
15.7 cm x 12cm x 8.7cm (6.2” x 4.7” x 3.4”) W,
D, H
Net Weight
0.08kg (0.2lb)
Shipping Weight
0.23kg (0.5lb)
Accessories
Included
Bracket set, double-sided adhesive dual lock
tape
Optional
RK-4PT rack adapter
Specifications are subject to change without notice at www.kramerav.com