Kramer FC-1DGH User manual

KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
FC-1DGH
DGKat to HDBT Converter
P/N: 2900-300279 Rev 1

FC-1DGH – Contents
i
Contents
1Introduction 1
2Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 2
2.3 Recycling Kramer Products 3
3Overview 4
4Defining the FC-1DGH 5
5Connecting the FC-1DGH 6
6Configuring the FC-1DGH 8
7Wiring the DGKat TP RJ-45 Connectors 9
8Technical Specifications 10
Figures
Figure 1: FC-1DGH DGKat to HDBT Converter Front Panel 5
Figure 2: FC-1DGH DGKat to HDBT Converter Rear Panel 5
Figure 3: Connecting the FC-1DGH DGKat to HDBT Converter 6
Figure 4: FC-1DGH Rear Panel DIP-switch 8
Figure 5: TP Pinout Wiring 9

FC-1DGH - Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront the video, audio, presentation, and broadcasting
professional on a daily basis. In recent years, we have redesigned and upgraded
most of our line, making the best even better!
Our 1,000-plus different models now appear in 13 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Products; GROUP 12: Digital Signage; and GROUP 13: Audio.
Congratulations on purchasing your Kramer FC-1DGH DGKat to HDBT Converter,
which is ideal for the following typical applications:
Home theater, presentation and multimedia applications
Boardrooms and classrooms

2
FC-1DGH - Getting Started
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Go to http://www.kramerelectronics.com/support/product_downloads.asp
to check for up-to-date user manuals, application programs, and to check
if firmware upgrades are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cable) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
Position your Kramer FC-1DGH away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
2.2 Safety Instructions
Caution:
No operator serviceable parts inside the unit
Warning:
Use only the Kramer Electronics input power wall adapter
that is provided with the unit
Warning:
Disconnect the power and unplug the unit from the wall
before installing
i
!
!

FC-1DGH - Getting Started
3
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.

4
FC-1DGH - Overview
3 Overview
The FC-1DGH is a DGKat and Ethernet to HDBaseT converter.
The FC-1DGH lets you connect any DGKat device and your Ethernet LAN over an
extended distance to any HDBaseT compatible receiver, (for example, a projector
with an HDBaseT input).
In particular, the FC-1DGH features:
A maximum data rate of 4.95Gbps (1.65Gbps per data channel)
System range on the DGKat side—up to 90m (295ft) at 1080i, or up to 30m
(98ft) at 1080p on shielded BC-DGKat524 cable; 90m (295ft) at 1080i, or up
to 70m (230ft) at 1080p on shielded BC-DGKat623 cable; 100m (330ft) at
1080i or up to 90m (295ft) at 1080p on shielded BC-DGKat7a23 cable
System range on the HDBaseT side—up to 130m (430ft) when using
BC−HDKat6a cable and up to 180m when used in conjunction with devices
that support long range mode
HDTV compatibility with support for resolutions up to 1080p @60Hz
HDCP compliance
Intelligent EDID handling and processing algorithm that ensures Plug and
Play operation for HDMI systems
12V DC power
A Kramer DigiTOOLS 
®enclosure

FC-1DGH - Defining the FC-1DGH
5
4 Defining the FC-1DGH
Figure 1 defines the front panel of the FC-1DGH DGKat to HDBT Converter.
Figure 1: FC-1DGH DGKat to HDBT Converter Front Panel
#
Feature
Function
1
ETHERNET RJ-45
Connector
Connect to the Ethernet LAN
2
STATUS LED
Lights yellow/green when there is a DGKat signal present.
Lights orange when there is no DGKat signal present
3
DGKAT IN RJ-45
Connector
Connect to the output of the DGKat source device, (see
Section 5)
4
ON LED
Lights green when the device is powered on
Figure 2 defines the rear panel of the FC-1DGH DGKat to HDBT Converter.
Figure 2: FC-1DGH DGKat to HDBT Converter Rear Panel
#
Feature
Function
1
LINK LED
Lights green when the HDBaseT link is valid
2
LIVE LED
Flashes green when there is an HDBaseT signal
3
HDBT OUT RJ-45 Connector
Connect to an HDBaseT-compatible receiver
4
SETUP 4-way DIP-switch
Sets the device behavior, (see Section 6)
5
12V DC
+12V DC connector for powering the unit, center
positive

6
FC-1DGH - Connecting the FC-1DGH
5 Connecting the FC-1DGH
Always disconnect/switch off the power to each device before
connecting it to your FC-1DGH. After connecting your FC-1DGH,
connect its power and then reconnect/switch on the power to each
device.
Figure 3: Connecting the FC-1DGH DGKat to HDBT Converter
To connect the FC-1DGH as illustrated in the example in Figure 3:
1. Connect a video and audio source, (for example, a laptop) to the DisplayPort
and Audio In connectors on the SID-X1N.
2. Connect an HDMI source, (for example, a Blu-ray Disc player) to the HDMI
input on the SID-X1N.
i

FC-1DGH - Connecting the FC-1DGH
7
3. Connect a video source, (for example, a computer graphics source) to the
PC/UXGA input on the SID-X1N.
4. Connect the SID-X1N to the DGKat In RJ-45 connector on FC-1DGH.
5. Connect the Ethernet LAN to the Ethernet RJ-45 connector on the
FC-1DGH.
6. Connect the HDBT OUT RJ-45 connector on the FC-1DGH to the HDBT IN
RJ-45 connector on the HDBT acceptor, (for example, a projector).

8
FC-1DGH - Configuring the FC-1DGH
6 Configuring the FC-1DGH
The Setup DIP-switch on the rear panel is used to control the behavior of the
device.
Figure 4: FC-1DGH Rear Panel DIP-switch
The following table describes the functions of the 4-way DIP-switch.
Switch
Function
Setting
1
EDID control
Down—Passes the EDID (default)
Up—Locks the current EDID
2
EDID deep color control
(to enable this control
switch 1 must be up)
Down—Passes the deep color parameter (default)
Up—Limits the color depth to 8 bits
3
EDID audio control (to
enable this control
switch 1 must be up)
Down—Passes the audio EDID parameter (default)
Up—Limits the audio to 2 channel LPCM
4
HDCP control
Down—Passes HDCP (default)
Up—HDCP off
Note: Deep color and EDID audio control are only enabled when the current EDID
is locked (DIP-switch 1 is up).

FC-1DGH - Wiring the DGKat TP RJ-45 Connectors
9
7 Wiring the DGKat TP RJ-45 Connectors
Connect/solder the cable shield to the RJ-45 connector shield at both ends of the
cable.
Do not use a crossed TP cable with this product.
Using a TP cable that is incorrectly wired may cause permanent
damage to the device
Do not use unshielded TP cables with this product
Figure 5 defines the TP pinout using a straight pin-to-pin cable with RJ-45
connectors.
EIA /TIA 568B
Figure 5: TP Pinout Wiring
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
Pair 1
4 and 5
Pair 2
1 and 2
Pair 3
3 and 6
Pair 4
7 and 8
!

10
FC-1DGH - Technical Specifications
8 Technical Specifications
INPUTS:
1 DGKat on an RJ-45 connector
1 Ethernet LAN on an RJ-45 connector
OUTPUT:
1 HDBaseT on an RJ-45 connector
OPERATION FREQUENCY:
Supports up to 4.95Gbps (1.65Gbps per graphics channel
1080p @60Hz)
COMPLIANCE WITH HDMI
STANDARD:
Supports HDMI, HDCP
INDICATOR LEDS:
ON, STATUS, LIVE, LINK
POWER SOURCE:
12V DC, 450mA
OPERATING TEMPERATURE:
0° to +40°C (32° to 104°F)
STORAGE TEMPERATURE:
–40° to +70°C (–40° to 158°F)
HUMIDITY:
10% to 90%, RHL non-condensing
COOLING:
Convection, vents
ENCLOSURE TYPE:
Aluminium
DIMENSIONS:
12.1cm x 6.99cm x 2.41cm (4.76" x 2.75" x 0.95") W, D, H
RACK MOUNT:
With optional adapter
FURNITURE MOUNT:
With included rubber feet
PRODUCT WEIGHT:
0.18kg (0.4lbs) approx.
SHIPPING WEIGHT:
0.68kg (1.5lbs) approx.
VIBRATION:
ISTA 1A in carton (International Safe Transit Association)
SAFETY REGULATORY
COMPLIANCE:
CE, c-UL, UL
EMI/EMC REGULATORY
COMPLIANCE:
CE, C-tick, FCC Class A, ICES, KCC, VCCI
ENVIRONMENTAL
REGULATORY COMPLIANCE:
Complies with appropriate requirements of RoHs and
WEEE
INCLUDED ACCESSORIES:
Power supply
OPTIONS:
RK-3T 19” rack adapter
WARRANTY:
7 years parts and labor
Specifications are subject to change without notice at http://www.kramerelectronics.com

For the latest information on our products and a list of Kramer distributors,
visit our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: [e-mail]
P/N:
2900-300279
Rev:
1
!
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing