Kramer 691 User manual

691/692 Quick Start
P/N:
2900- 301392QS
Rev:
6
Scan for full manual
691/692 Quick Start Guide
This guide helps you installand use your 691/692 for thefirst time.
Go to www.kramerav.com/downloads/691 or www.kramerav.com/downloads/692 to download the latest
user manual and check if firmware upgrades are available.
Step 1: Check what’s in the box
691 HDBT 2.0 Transmitter or
692 HDBT 2.0 Receiver
1 OSP-MM1 Fiber Optic SFP+ Transceiver
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your 691/692
691
#
Feature
Function
1
USB Connector
Connect to the USB host (for example, a laptop) for traffic extension to remote
connected USB devices.
2
LINK LED
Lights green when the HDBT link is active.
3
IN LED
Lights green when an active HDMI source is connected.
4
ON LED
Lights green when the device receives power.
5
HDMI IN Connector
Connect to the HDMI source.
6
IR 3.5mm Mini Jack Connector
Connect to an external infrared transmitter or receiver for traffic extension.
7
RS-232 3-pin Terminal Block
Connect to an RS-232 controller for traffic extension (for example, a PC to control
the projector).
8
AUDIO IN 3.5mm Mini Jack
Connect to the stereo, analog audio source.
9
OUT IN SFP+ Connector
Connect the fiber optic cable to the OUT IN SFP+ connectors (OSP-MM1 included).
10
SETUP 4-way DIP-switch
Sets the device functions.
11
CONTROL
RS-232 3-pin Terminal
Block
Connect to the serial controller to control this device.
12
ETHERNET RJ-45
Connector
Connect to the LAN to extend network traffic to the receiver and Ethernet controller
to control this device.
13
RESET Switch
Press and hold for 5 seconds to reset the device to factory default settings.
Press and immediately release to power-cycle the device (Reset).
14
PROG Mini USB Connector
Connect to a PC to perform firmware upgrades.
15
12V DC Power Connector
Connect to the supplied power adapter.

692
#
Feature
Function
16
USB Connectors
Connect to the USB devices (for example, a camera, keyboard, mouse and so on)
for traffic extension to a remote connected USB host.
17
LINK LED
Lights green when the HDBT link is active.
18
ON LED
Lights green when the device receives power.
19
HDMI OUT Connector
Connect to the HDMI acceptor.
20
IR 3.5mm Mini Jack Connector
Connect to an external infrared transmitter or receiver for traffic extension.
21
RS-232 3-pin Terminal Block
Connect to an RS-232 Controller for traffic extension (for example, a PC to control
the Blu-ray player on the transmitter side).
22
AUDIO OUT 3.5mm Mini Jack
Connect to the stereo, analog audio acceptor.
23
OUT IN SFP+ Connector
Connect the fiber optic cable to the OUT IN SFP+ connectors (OSP-MM1 included).
24
SETUP 4-way DIP-switch
Sets the device functions.
25
CONTROL
RS-232 3-pin Terminal
Block
Connect to the serial controller to control this device.
26
ETHERNET RJ-45
Connector
Connect to the LAN to extend network traffic to the transmitter and Ethernet
controller to control this device.
27
RESET Switch
Press and hold for 5 seconds to reset the device to factory default settings.
Press and immediately release to power-cycle the device (reset).
28
PROG Mini USB Connector
Connect to a PC to perform firmware upgrades.
29
12V DC Power Connector
Connect to the supplied power adapter.
Step 3: Mount 691/692
Install 691/692 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/691).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/691).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your 691/692. For best results, we recommend
that you always use Kramer high-performance cables to connect AV equipment to the 691/692.
For optimal performance, use the RECOMMENDED Kramer cables available at www.kramerav.com/product/691.
Using third-party cables may cause damage!
To install/replace the OSP-MM1 or other Kramer recommended
SFP+ transceiver:
1. Pull the bail out and remove the currently installed transceiver,
insert the protective cap and store in a safe place.
2. Make sure the bail of the new transceiver is pushed up, in the
closed position.
3. Insert the new transceiver into the relevant optical device SFP+
slot and push it in until it clicks.
4. Remove the protective cap and store it in a safe place for future
use.
Warning: Connecting the OSP SFP+ connector to an LC(APC) fiber
connector may cause poor performance and damagethe connector!
Refer to www.kramerav.com/downloads/691 for more information.
Warning: Class 1 Laser Product
•Invisible laser radiation present.
•Avoid long-term viewing of laser.
•Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes
and magnifying lenses, but not spectacles or contact lenses).
•Avoid placing optical devices in the emitted beam that could cause the concentration of the laser
radiation to be increased.

SETUP DIP-Switches
A DIP-switch that is down is on, up is off. Changes to the DIP-switches only take effect on power-up. After
changing a switch, reboot the device.
#
Function
Applicable to:
Status
1
For future use
691 and 692
—
2
Audio source priority
691 only
Off—Embedded audio (factory default)
On—Analog audio
3
EDID lock
691 and 692
Off—Automatic EDID acquisition (factory default)
On—Lock (locks the current EDID so that changes on the
output do not result in changes to the EDID)
4
Audio mode selection
691 only
Off—Auto (factory default)
On—Manual
Step 5: Connect power
Connect the power cord to 691/692 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Operate 691/692
Embedded Web pages:
RS-232 and Ethernet parameters and defaults:
RS-232
Protocol 3000
Baud Rate:
115,200
Stop Bits:
1
Data Bits:
8
Parity:
None
Command format:
ASCII
Example (get device model name):
#model?<cr>
TCP/IP
IP Address:
192.168.1.39
UDP Port #:
50000
Subnet mask:
255.255.000.000
TCP Port #:
5000
Default gateway:
192.168.0.1
Embedded Webpages Authentication
User/Password
Admin/Admin
Full Factory Reset
Rear panel
button:
Press and hold for 5 seconds to reset the device to factory default
settings.
P3K command:
#factory<cr>
Embedded Web
pages:
Select Device Settings page and click Factory reset
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.