Kramer TP-590Rxr User manual

TP-590RXR Quick Start (P/N: 2900-300860QS REV 2)
P/N:
2900- 300860QS
Rev:
2
Scan for full manual
TP-590RXR Quick Start Guide
This guide helps you install and use your TP-590RXR for the first time.
Go to www.kramerav.com/downloads/TP-590RXR to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
TP-590RXR HDMI Line Receiver
4 Rubber feet
1 Bracket set
1 Power supply (12V DC)
1 Quick start guide
Step 2: Get to know your TP-590RXR
#
Feature
Function
1
USB 1 –4 Connectors
Connect to the USB peripheral devices, (forexample, USB camera, computer mouse, or
keyboard).
2
POE STATUS LED
Lights green when poweris received over the TP connection.
3
LINK LED
Lights green when the HDBT link is valid.
4
ON LED
Lights green when the device receives power.
#
Feature
Function
1
HDBT IN RJ-45 Connector
Connect to the HDBT OUT RJ-45 connector on the HDBT transmitter.
2
IR 3.5mm Mini Jack Connector
Connect to an external infrared transmitter or sensor.
3
RS-232 3-pin Terminal Block
Connect to an RS-232 device to be controlled, for example, a projector.
4
AUDIO OUT 3.5mm Mini Jack
Connector
Connect to the stereo, analog audio acceptor.
5
HDMI OUT Connector
Connect to the HDMI acceptor.
6
SETUP 4-way DIP-switch
Set the device behavior (see Step 4).
7
CONTROL
RS-232 3-pin
Terminal Block
Connect to the serial controller for this device.
8
ETHERNET
RJ-45 Connector
Connect to the Ethernetcontroller to control this device or to a LAN to pass network traffic.
9
RESET Switch
Press and hold for 5 seconds to reset the device to factory default settings.
Press and immediately release to power-cycle the device (Reset).
10
PROG Mini USB Connector
Connect to a PC to perform firmware upgrades.
11
12V DC Power Connector
Connect to the supplier power adapter ifpower is not supplied from a PoE device via the TP
cable.

Step 3: Install TP-590RXR
Install TP-590RXR using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/TP-590RXR.
•Mount the unit in a rack using an optional RK-T2B rack adapter.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your TP-590RXR. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to TP-590RXR.
Setting the DIP Switches
Set the DIP-switches using the table on the right. The ON/OFF
positions are as follows:
•Switch down = ON
•Switch up = OFF
Note: Changes to the DIP-switches only take effect on power-up.
Function
Status
1
Range
mode
Off—Extended range (provides increased
range at a reduced bandwidth)
On—Normal range (factory default)
2
Reserved
Off—Factory default
3
EDID lock
Off—Automatic EDID acquisition (factory
default)
On—Lock (locks the current EDID so that
changes on the output do not result in
changes to the EDID)
4
Reserved
Off—Factory default

Step 5: Connect the power
Connect the 12V DC power supply to TP-590RXR and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Operate TP-590RXR
Operate TP-590RXR via:
•Remotely, using Protocol 3000
commands via RS-232 or Ethernet
•Embedded web pages via the
Ethernet
•Remotely, using an IR remote
control transmitter
Default Parameters
Parameter
Value
Name
KRAMER_
Model
TP-590RXR
IP Address
192.168.1.39
UDP Port
50000
TCP Port
5000
Network Mask
255.255.0.0
Gateway Address
192.168.0.1
RS-232 Baud Rate
115200
HDCP Mode
Followoutput
Audio Selection Mode
Auto
Video Signal Loss Timeout (no 5V)
0 seconds
Video Signal Loss Timeout (5V present)
10 seconds
Protocol 3000 Commands
Command
Description
Command
Description
#
Protocol handshaking
LOGIN
Set/get protocol permission
AV-SW-TIMEOUT
Set/get video auto-switch timeout
LOGOUT
Cancel current permission level
BUILD-DATE?
Read device build date
MODEL?
Read device model
CPEDID
Copy EDID data from the output to the input
NAME
Set/get machine (DNS) name
DIR
List files in device
NAME-RST
Reset machine name to factory default
(DNS)
DISPLAY?
Valid / Invalid output
NET-DHCP
Set/get DHCP mode
ETH-PORT
Set/get Ethernet port protocol
NET-GATE
Set/get gateway IP
FACTORY
Resets the device to factory default
NET-IP
Set/get IP address
FS-FREE?
Get file system free space
NET-MAC?
Get MAC address
GEDID
Read EDID data
NET-MASK
Set/get subnet mask
GET
Get file
PASS
Set/get Password
HDCP-MOD
Set/get HDCP mode
PROT-VER?
Get device protocol version
HDCP-STAT?
Get HDCP signal status
RESET
Reset device
HELP
Get command list or help for specific
command
SECUR
Start / Stop Security
LDEDID
Write EDID data to input
SIGNAL?
Get input signal lock status
LDFW
Load new firmware
SN?
Read device serial number
LOAD
Load new firmware
UPGRADE
Perform firmware upgrade
LOCK-EDID?
Get EDID lock status
VERSION?
Read device firmware version

Using the Embedded Web Pages
The TP-590RXR can be operated remotely using the
embedded web pages. Access the web pages from the
control computer using a web browser and an Ethernet
connection.
Before attempting to connect:
•Ensure that your browser is supported.
•Ensure that JavaScript is enabled.
Note: In the event that a Web page does not update
correctly, clear your Web browser’s cache.
Note: Only one instance of the web pages can be open at a
time.
To browse the TP-590RXR web pages:
1. Open your Internet browser.
2. Type the IP number of the device (default =
192.168.1.39) in your browser.
If authentication is enabled, the following window
appears.
3. Enter the valid username and password to access the
web pages.
Following a successful logon, the Default page
appears.
#
Item
Description
1
Video Settings
Viewthe current video settings.
2
Reveal Button
Click to reveal the Page Selection
panel.
4. Click the Reveal button to open the left hand side
page panel.
5. Select the required page from the Page Selection
Panel to configure the device:
Video Settings Page: Modify the video and timeout
parameters.
Device Settings Page:
•View some of the device characteristics (for example,
model and web version)
•Edit IP settings
•Load and save configurations
•Reset the device to factory default settings
EDID Management Page:
•Copy EDID data to either or both of the inputs
•Lock the EDID on each input independently
Note: Do not power up the display before locking the EDID.
Firmware Upgrade Page:
•View the current firmware version
•Upgrade the firmware
Authentication Page: Assign or change logon
authentication details.
About Page: View the Web page version and Kramer
Electronics Ltd company details.