Kramer TP-583T User manual

TP-583T, TP‑583R Quick Start
P/N:
2900- 301158QS
Rev:
2
Scan for full manual
TP-583T/TP-583R Quick Start Guide
This guide helps you install and use your TP-583T/TP-583R for the first time.
Go to www.kramerav.com/downloads/TP-583T, TP-583R to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
TP-583T HDMI Line Transmitter or
1 Power adapter and cord
1 Quick start guide
TP-583R HDMI Line Receiver
4 Rubber feet
1 Bracket set
Step 2: Get to know your TP-583T and TP-583R
TP-583T
#
Feature
Function
1
IN LED
Lights green when an active source device input signal is detected.
2
OUT LED
Lights green when an active, far-end sink (acceptor) connection is detected via the
HDBT link.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT receiver.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a receiver (for example, TP-583R, TP-
780R and so on).
6
HDMI™ IN Connector
Connect to an HDMI source.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin
Terminal Block Connector
Connect to a laptop to control the receiver or perform firmware upgrade.
Connect to a controller device (for example, SL-240C) to serially control a remote
device (for example, the HDMI OUT acceptor) that is connected to TP-583R.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.

TP-583R
#
Feature
Function
1
IN LED
Lights green when an active, far-end source device input signal is detected via the
HDBT link.
2
OUT LED
Lights green when an active sink (acceptor) connection is detected.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT transmitter.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a transmitter (for example, TP-583T,
TP-780T and so on).
6
HDMI® OUT Connector
Connect to an HDMI acceptor.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin
Terminal Block Connector
Connect to a laptop to control the receiver or perform firmware upgrade.
Connect to a serially controlled device (for example, the HDMI OUT acceptor) to enable
its control by a remote controller device (for example, SL-240C) that is connected to
TP-583T.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Install TP-583T/TP-583R
Install TP-583T/TP-583R using one of the following methods:
Attach the rubber feet and place the unit on a flat surface.
Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more
information go to www.kramerav.com/downloads/TP-583T, TP-583R.
Mount the unit in a rack using the recommended rack adapter (see
www.kramerav.com/product/TP-583T, TP-583R).

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your TP-583T/TP-583R. For best results, we recommend
that you always use Kramer high-performance cables to connect AV equipment to TP-583T/TP-583R.
RJ-45 Pinout:
For HDBT cables, it is recommended that the cable
ground shielding be connected/soldered to the
connector shield:
PIN EIA /TIA 568B
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
For optimum range and performance use the recommended Kramer cables available at
www.kramerav.com/product/TP-583T, TP-583R.

DIP-Switch Settings
The DIP-switches are used to:
•Set the compression levels and resolutions.
•Enable RS-232 signal extension.
•Upgrade the firmware.
•Determine IR signal pass-through.
All the DIP-switches are set to OFF (up) by default.
To use your TP-583T or TP-583R with any other standard HDBaseT
extender (without compression), verify that DIP-switch 1B is OFF (up).
A –DIP-switch Settings
#
Feature
DIP-switch Settings
1A
Reserved
Set to OFF (up).
2A
Set the Compression Level
(for extended range)
OFF (up) –Standard compression level.
ON (down) –High compression level for additional extension.
B –DIP-switch Settings
Changes to DIP-switches 2B and 3B only take effect after power cycling the device.
#
Feature
DIP-switch Settings
1B
Define Compressed
Resolutions
OFF (up) –Compress signal resolutions higher than 1080p.
ON (down) –Compress all signal resolutions to enable extended reach.
2B, 3B
Define RS-232 Function
OFF (up), OFF (up) –Embed RS-232 data and control signals over the
extension line.
Other DIP-switch settings are reserved for firmware upgrade.
For further details, contact [email protected].
4B
Define IR Pass-through
OFF (up) –Pass-through the IR signal to the IR port via IR cable.
ON (down) –Add IR modulation to the IR output signal (applies only when
the IR port is connected to an IR emitter cable).
The IR Pass-through DIP-switch setup depends on the IR
control configuration. We recommend that you test which
position best suits your application.
Step 5: Connect the power
Connect the 12V DC power adapter to TP-583T/TP-583R and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power adapter that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.