Kramer VP-427UHD User manual

VP-427UHD Quick Start
P/N:
2900- 301156QS
Rev:
3
Scan for full manual
VP-427UHD Quick Start Guide
This guide helps you install and use your VP-427UHD for the first time.
Go to www.kramerav.com/downloads/VP-427UHD to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
VP-427UHD HDMI/HDBT Receiver/Switcher/Scaler
1 Bracket set
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your VP-427UHD
#
Feature
Function
1
IN LED
Lights green when the HDMI input is selected, blue when HDBT is selected and flashes if no
input signal is detected.
2
HDBT/HDMI Button
Press to select the remote HDBT or the local HDMI source.
3
HDMI™OUT Status LED
Lights green when an HDMI acceptor is connected.
4
HDBT LINK status LED
Lights green when an HDBT link between a transmitter and the receiver is successfully
established and is active.
5
ON LED
Lights green when the unit is powered from the local 12V DC source and lights blue when
receiving PoE via HDBT.
6
MENU Button
Press to enter the OSD menu. When in OSD, press to exit one level up.
7
ENTER Button
When not in OSD, press ENTER to view the input status on the display (the selected input,
resolution and frame rate, HDCP state and aspect ratio).
When in OSD, press to select and carry out a menu item or to accept a parameter value.
Press and hold together with the –or + to increase the speed of parameter-decrement or
increment, respectively.
Press and hold for about 3 seconds to reset a menu parameter to its default values.
8
–Button
Press and hold together with the + button to reset the output resolution to 1080p (default).
In OSD, press to move back through the menu list or to decrement a parameter value (or
press together with ENTER to speed up parameter decrement).
9
+ (also Freeze) Button
Press and hold together with the –button to reset the output resolution to 1080p (default).
When not in OSD: press to freeze the image;
In OSD, press to move forward through the sub-menu list or to increment the parameter
value (or press together with ENTER to speed up parameter increment).
10
FREEZE LED
Lights green when freezing the image.
11
HDBT IN RJ-45 Connector
Connects to an HDBaseT transmitter.
12
HDMI IN Connector
Connect to an HDMI source.
13
HDMI OUT Connector
Connects to an HDMI acceptor.

#
Feature
Function
14
AUDIO OUT 5-pin Terminal
Block Connector
Connect to a balanced or unbalanced stereo audio acceptor.
15
S/PDIF digital audio output
Connect to a digital audio acceptor.
16
IR 3.5mm Mini Jack
Connect to an IR Sensor (in) or Emitter (out) to control a remote device.
17
Ethernet RJ-45 Connector
Connect via a LAN to a PC to control the VP-427UHD and/or extend Ethernet signals to the
HDBT transmitter via the HDBT IN port.
18
RS-232 Terminal Block
Connector
Connects to a controller to control the VP-427UHD or to extend RS-232 signals between the
VP-427UHD and the RS-232 port of the connected HDBT transmitter.
19
12V DC
+12V DC connector for powering the unit.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Install the VP-427UHD
Install VP-427UHD using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/VP-427UHD.
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/VP-427UHD).
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-427UHD. For best results, we recommend that
you always use Kramer high-performance cables to connect AV equipment to the VP-427UHD.
For optimum range and performance use the recommended Kramer cables available at
www.kramerav.com/product/VP-427UHD
Connect AUDIO OUT
To a balanced stereo
audio acceptor:
To an
unbalanced
stereo audio
acceptor:
Step 5: Connect the power
Connect the 12V DC power supply to VP-427UHD into the mains electricity. When the connected transmitter provides PoE for the
VP-427UHD, you do not need to connect it to the 12V DC power supply.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Warning:
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information
Step 6: Operate the VP-427UHD
Operate the VP-427UHD:
•Toggle the HDBT/HDMI front panel
button to select the input.
•Control device via OSD menu or remotely
by RS-232 serial commands or Ethernet
transmitted by a touch screen system,
PC, or other serial controller.
•Control remote devices on the
transmitter via RS-232, IR or Ethernet
signal extension.
RS-232 Control / Protocol 3000?
Baud Rate:
115,200
Parity:
None
Stop Bits:
1
Data Bits:
8
Command Format:
ASCII
Example: (get device model): #MODEL?<CR>
Default Ethernet Parameters
IP Address:
192.168.1.39
UDP Port #:
50000
Gateway:
0.0.0.0.
Subnet mask:
255.255.0.0
TCP Port #:
5000