Kramer WP-211T User manual

WP-211T Quick Start
P/N:
2900- 301088QS
Rev:
4
Scan for full manual
WP-211T Quick Start Guide
This guide helps you install and use your WP-211T for the first time.
Go to www.kramerav.com/downloads/WP-211T to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
WP-211T 1 Gang Ethernet and K-NET Control Keypad
1 Power adapter and cord
1 Quick start guide
1 Frame (or frame set) and faceplate
Installation accessories
Step 2: Get to know your WP-211T
#
Feature
Function
1
INPUT 1
HDMI Connector
Connect to an HDMI source to route to HDBT OUT.
Button
Press momentarily to manually select HDMI 1 (button lights orange).
2
Operation Mode
DIP-switches
By-default the DIP-switches are both set to OFF (left).
Controlling via the INPUT buttons overrides all DIP-switch settings and automatic
switching until the manually selected source disconnects, becomes inactive or WP-211T
is powered off.
DIP-switch 1
OFF (left) - Last connected mode.
ON (right) - Priority mode according to DIP-switch 2 settings.
DIP-Switch 2
OFF (left) - INPUT 1 is the default priority.
ON (right) INPUT 2 is the default priority.
WP-211T DIP-switches are located behind the faceplate and should be set during installation, before placing the
faceplate. Pressing an input button manually selects that input, independent of the DIP-switch settings.
3
INPUT 2
HDMI™Connector
Connect to an HDMI Source to route to HDBT OUT.
Button
Press momentarily to manually select HDMI 2 (button lights orange).
4
Grounding Screw
Connect to the common ground (optional) to prevent static electricity from impacting the
performance of the unit.

#
Feature
Function
5
GND 5V DC 2-pin Terminal
Block Connector
Connect to the supplied power adapter. Not needed on the WP-211T if there is a PoE
provider over HDBaseT.
6
HDBT OUT RJ-45 Connector
Connect to an HDBaseT receiver (for example, TP-580R).
Step 3: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your WP-211T. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the WP-211T.
Grounding the WP-211T
#
Component Description
1
M3X6 screw
2
1/8" Toothed Lock
Washer
3
M3 Ring Tongue Terminal
To ground the WP-211T:
1. Connect the ring tongue terminal to the building grounding point wire (it is recommended to use a green-yellow
AWG#18 (0.82mm) wire, crimped with a proper hand-tool).
2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above.
3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue terminal) into the grounding screw hole and
tighten the screw.

Step 4: Install WP-211T
After connecting the ports, insert the device into the in-wall box and connect the parts as shown in the illustrations below:
EU/UK Version
US-D Version
DECORA® design frames are included in US-D models.
We recommend that you use any of the following standard 1 Gang in-wall junction boxes (or their equivalent):
•US-D: 1 Gang US electrical junction boxes.
•EU: 1 Gang in-wall junction box, with a cut-hole diameter of 68mm and depth that can fit in both the device and the
connected cables (DIN 49073).
•UK: 1 Gang in-wall junction box, 75x75mm (W, H), and depth that can fit in both the device and the connected cables
(BS 4662).
Step 5: Connect the power
If the device is not powered via HDBT PoE, connect the 5V DC power adapter to the WP-211T and plug the adapter into the
mains.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.

Technical Specifications
Inputs
2 HDMI
On female HDMI connectors
Outputs
1 HDBT
On a female RJ-45 connector
Video
Max. Data Rate
8.91Gbps (2.97Gbps per graphic channel)
Max. Resolution
4K@60Hz (4:2:0)
Standard Compliance
HDCP 2.2 (does not support conversion to HDCP 1.4),
HDMI 1.4
Controls
DIP-Switches
Last connected/priority DIP-switches
Front Panel
Input select buttons
Power
Consumption
5V DC, 780mA
Source
5V DC, 4A with open DC head
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE, UL
Environmental
RoHs, WEEE
Enclosure
Size
1 Gang wall plate
Cooling
Passive heat sink (metal sheet)
General
Net Dimensions (W, D, H)
US-D: 7cm x 3.7cm x 11.4cm (2.8" x 1.5" x 4.5)
EU: 8cm x 3.8cm x 8cm (3.1" x 1.5" x 3.1)
UK: 8.6cm x 3.8cm x 8.6cm (3.4" x 1.5" x 3.4")
Shipping Dimensions (W, D,
H)
23.2cm x 13.6cm x 10cm (9.1" x 5.4" x 3.9")
Net Weight
0.2kg (0.4lbs) approx..
Shipping Weight
0.6kg (1.2lbs) approx.
Accessories
Included
1 Power adapter, 1 power cord, installation accessories
US-D version: 2 US Frame sets and faceplates (1 in black
and 1 in white)
European version: 1 EU white frame, 1 UK white frame, 1
EU/UK white faceplate
Specifications are subject to change without notice at www.kramerav.com
DECORA® is a registered trademark of Leviton Manufacturing Co., Inc.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.