Kraus KBF-1401 User manual

IndyTM Single Lever Basin Faucet
KBF-1401
R
INSTALLATION MANUAL
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Plumbing LLC I REV. November 8, 2021

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Read all instructions and safety warnings and ensure you have all
tools, parts, and equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 1 3/8”
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
ACID
R
STOP

4
Tools Required
4
Adjustable Wrench Phillips Screwdriver Silicone Sealant
Safety Goggles Pipe Tape

55
Diagram and Parts List
A. Faucet Body
B. Metal Base Ring
C. Rubber Washer
D. Metal Washer
E. Lock Nut
F. Wrench
G. Hex Wrench
A
G
C
E
F
B
D

66
Installer Tip:
Shut off main water supply before installing new faucet.
Faucet Dimensions
15°
Ø2" (50mm)
4 5/8" (117mm)
5 1/8" (131mm)
6 1/4" (159mm)
3 3/8" (86mm)
5/16-18UNC Ø1 3/8"
(35mm)
1 3/8" (35mm)
9/16"-UNEF-24

7
Step 1. Install faucet and mounting hardware
Place the faucet (A) through the
mounting holes in the sink until
the faucet (A) sits on top of the
sink. Secure the faucet (A) to the
sink using the rubber (C) and
metal washers (D) and lock nut (E)
provided. Ensure the washers
(C&D) and waterlines have no
interference.
Step 2. Connect waterlines to main valve
Attach waterlines to angle stops
and tighten until snug. Turn on
angle stops and check for leaks.
(DO NOT TURN FAUCET ON)
A
E
E
F
C & D C
D
NOTE: Make sure filter washers
are installed.

8
Replacement Parts
1. Metal Handle
2. Handle Button
3. Set Screw M5x6RB
4. Cartridge Cover
6. Locking Nut
7. Cartridge
8. Aerator
9. Metal Base Ring
10. Rubber Washer
12. Mounting Nut
Replacement Parts List Finish/Color Part #
KP06177
KP06026
KP06052
KP06080
KP06059
KP06176
KP06101
KP06183
KP06181
KP06179
KP06178
KP06182
KP06180
KP06050
KP06185
GR, BL, YL*
5. O-Ring
11. Metal Washer
SFS,MB,CH,BG*
1
6
4
8
7
9
10
11
13
14
3
2
*Denotes faucet component color options:
BG - Brushed Gold
CH- Chrome
MB - Matte Black
SFS - Spot Free Stainless Steel
BL - Black
GR - Grey
YL - Yellow
5
12 13. Spanner Key
15. Filter Washers
14. Hex Wrench
15
SFS,MB,CH,BG*
SFS,MB,CH,BG*

9
Trouble-Shooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
Leakage under the faucet
handle
Bonnet nut has come loose. Remove the index. Loosen set screw with
hex wrench. Remove the handle. Unscrew
cap (by hand only). Tighten bonnet nut
with an adjustable wrench.
Aerator drips or has inconsistent
water flow pattern
Aerator is dirty or not
seated properly.
Unscrew aerator with aerator wrench and
clean out debris.
Water does not shut off
completely
Cartridge may need to be
adjusted or replaced.
Remove the index. Loosen set screw with
hex wrench. Remove the handle. Unscrew
cap (by hand only). Tighten bonnet nut
with an adjustable wrench. Remove the
cartridge. Check for cracks.
There is leaking from the
sink drain at the base of
the sink
The sink has a rough or
irregular surface.
Apply additional silicone sealant to the
beveled side of the drain flange. Retighten
and test for leaks.
There is a low flow of water The screen filter in the hose
connectors is dirty.
Turn off the water supply at water valve
and unscrew the hose connectors from
water supply lines. Clean the screen
in the water lines with hot water, removing
any debris or calcium build up.
PROBLEM CAUSE ACTION

10
Codes/Standards Applicable:
Faucet - Lifetime Limited Warranty
Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the
Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is
non-transferable.
Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal
usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.
Kraus warrants the Faucet's sprayhead assembly (including the engine, aerators, structure, restrictors, back flow
preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel) of the product
to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of
purchase.
Kraus warrants the Faucet's cartridge to be free from defects in material and workmanship under normal usage for a
period of five (5) years from the date of purchase.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired
or replaced with a product of equal value at the option of Kraus.
Commercial Warranty
Kraus USA Plumbing, LLC (“Kraus”) warrants its Products for a period of one (1) year to commercial purchasers of
Products used in industrial, commercial and business applications.
Care and Cleaning Instructions
Certain cleaning products may cause damage to a Product's finish and use of the following on the Product will void this
warranty:
·Abrasive cleaners such as powders, bleach, ammonia, alcohol or chorine
·Abrasive pads, steel wool or wire brushes
What is Not Covered
This warranty does not cover Products that were discontinued when purchased or display Products, whether such
Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not
cover any free gifts included with purchase.
This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application),
abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance,
alteration of the Product, or failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus
recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the
installation of bathroom and/or kitchen manufactured goods.
R
UPC
CR
IAP
CR
NSF/ANSI 372 LEAD FREE
ASME A112.18.1
1.2GPM 4.5L/min maximum
MOR&T
NSF/ANSI 372
NSF/ANSI 61