KS Tools 160.0741 User manual

www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com
KS TOOLS Werkzeuge-Maschinen GmbH ●Seligenstädter Grund 10 - 12 ●D - 63150 Heusenstamm ●e-mail: kstools@kstools.de ●www.kstools.com
KS TOOLS PDA Région de Brumath ●1 rue de Londres ●F - 67670 Mommenheim ●e-mail: kstools@kstools.fr ●www.kstools.fr
DE/AKA/AAI/03-05-2019
BEDIENUNGSANLEITUNG - OPERATING INSTRUCTIONS - NOTICE D‘UTILISATION
160.0741 - 160.0745
Lufthydraulischer Wagenheber
Pneumatic hydraulic trolley jack
Cric hydro-pneumatique

www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com
Introduction
Dear customer!
Thank you for buying one of our products. You can find all the information you need in these operating instructions.
Please read the instructions completely with care and observe the advice given. The operating instruction is part of the
item and should be kept intact. The manufacturer is not liable for personal injuries and material damages which result
from improper use.
1. Provisions for use
The manufacturer shall not be held liable for personal and/or material damage which can be traced back to unintended
use of the tool.
!
Pay heed to the vehicle manufacturer‘s specifications!
2. Technical data
Art.-No. A
mm B
mm Max.
lift load
t
C
mm Max.
lift load
t
D
mm Max.
lift load
t
E
mm Max.
lift load
t
F
mm G
mm
160.0741 150 73 40 66 20 - - - - 75 45
160.0742 170 88 40 81 20 - - - - 75 45
160.0743 125 57 40 49 20 53 10 - - 75 45
160.0744 150 57 60 60 40 61 22 65 11 75 45
160.0745 230 111 80 102 50 - - - - 75 45
This pneumatic hydraulic trolley is supplied ready for use. The hydraulic oil used
is ISO viscosity 32. For every oil change, it is necessary to unscrew the fill hole
with the type of your pneumatic hydraulic trolley.
For oil change refer to the table containers of oil jacks.
3. Safety and usage instructions
Tools may in principle only be used for the purpose intended, under the conditions envisaged and within the limitations
as to their use.
- Please read the operation manual carefully and comprehend it thoroughly before using the product.
- The product shall be used on solid ground with supporting capacity. It shall not be used on the inclined or uneven
ground to avoid the objects to be left from shifting or side slipping.
- When lifting vehicles, please ensure that anti-slip and anti-shifting backers for the wheel are placed before lifting.
AFG
B
C
D
E
Art.-No. Oil Levels
(Liter)
160.0741 0,8
160.0742 2,8
160.0743 2,6
160.0744 1,8
160.0745 5,8

www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com
- The product only serves as a hoisting tool but not a supporting tool. It shall work with security bracket and brace.
Operators are not allowed to lift objects without placing security bracket and brace after the hoisting of the pneumatic
hydraulic jack.
- For security reasons, the air supply pipe shall be shut down after the pneumatic jack lifts..
4. Operation
1. Make sure when you unpack the pneumatic hydraulic trolley that he is complete and has not suffered damage during
transport.
2. Insert the handle into the base and secure it by crossing the center line and fasten all with the circlip.
3. Loosen the screw on the top of the handle and screw in place, the wheel.
4. Place the collars on each side of the trolley on their respective support.
5. Getting started
1. Lock the handle in the desired position by lowering the lever.
2. Turn the knob on the top of the handle clockwise to raise the trolley.
3. Turn the knob on the top of the handle to the left to lower the trolley.

www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com • www.kstools.com
6. Maintenance
Incorrect or defective replacement parts can lead to damage.
7. Checks
All tools are to be checked for damage.
8. Disposal
The tool is to be disposed of or recycled in accordance with the legislation of the respective country.
9. Guarantee
The KS Tools Werkzeuge-Maschinen GmbH guarantee applies for all tools that are used under normal usage conditions.
The following are excluded from the guarantee:
• Consumables e.g. any type of cutting tools, cutting inserts and disks, cutting and scraping tools, brooms, brushes,
files, batteries, bits or bit sockets, rotor blades in pneumatic devices, isolators on heating coils, any type of fuses,
carbon brushes, etc.
• Faulty functioning of parts that show usage-related or other natural wear and tear, as well as tool defects that can
be traced back to usage-related or other natural wear and tear.
• Defects in the tool that can be traced back to a failure to observe the operating instructions, improper use, use under
abnormal environmental conditions or unsuitable operating conditions, overloading or improper maintenance.
Also defects in tools caused by the use of accessory parts or other parts that are not KS Tools original parts.
• Tools which have been modified or equipped with additions.
• Minor deviations from the intended quality that are however insignificant for the value and suitability for use of the tool.
The guarantee period is 12 months in cases of industrial or equal use.
The guarantee period starts on the date of purchase by the commercial end customer. The date of the original purchase
receipt is decisive. For technical products with limited guarantee types A, B and C, the user must principally submit the
purchase receipt in addition to the serial number of the device, if present.
The guarantee applies under consideration of the guarantee type for the duration specified in the price list valid on the
day the product was purchase.
If no guarantee claim exists for the product (expiration of the guarantee time, guarantee exclusion for the reasons listed
in Sec. 2) but the repair is still possible, this will only be carried our following approval of the cost estimate by the user.
This manual suits for next models
1
Table of contents
Other KS Tools Jack manuals