KUSSMAUL 091-11-DV User manual

170 Cherry Avenue
West Sayville, NY 11796
www.kussmaul.com
Ph: 800-346-0857
Fax: [phone]
[email protected]
3 YEAR WARRANTY
File: 091-11DV-1
Rev: A
Revised By: PSS
Date: 08-30-05
INPUT: 115 or 230 volt, 50/60 Hz, 2 Amps
OUTPUT: 11 Amperes D.C.
MODEL #: 091-11-DV
AUTO CHARGE 11DV
AUTOMATIC BATTERY CHARGER
INSTRUCTION MANUAL
NOTE :
This charger is
designed for
vehicles with
dual batteries
and negative ground.

170 Cherry Avenue
West Sayville, NY 11796
www.kussmaul.com
Ph: 800-346-0857
Fax: [phone]
[email protected]
2
INTRODUCTION
The Auto Charge 11DV Battery Charger is a compact completely automatic charger designed for
installation on vehicles with two batteries. An internal charge divider charges both batteries simultane-
ously while maintaining battery isolation. Remote sensing permits long lines between the charger and the
batteries by compensating for the voltage drop in the charging wires. An ammeter provides continuous
indication of the charger output. Input power may be either 115 volts or 230 volts . A voltage selector
switch is provided on the end panel near the output terminal strip.
Construction of the Auto Charge 11DV is extremely rugged to withstand the shock and vibration
normally encountered by vehicle mounted equipment. The unit operates completely automatically and
stops charging the batteries when they are fully charged. There is no trickle charge and therefore no
danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc.,
are automatically supplied with current by the charger.
INSTALLATION
The Auto Charge 11DV Automatic Battery Charger should be installed in an area with adequate
ventilation. A power cord is supplied for connection to 115 or 230 volts 60 Hz.
1. Mount the charger using the four holes provided for this.
2. Connect the wiring from the batteries to the Output Terminal Strip. Spade lugs that have been
securely crimped, or soldered, should be used.
3. Connect the wiring to the batteries. Ring lugs that have been securely crimped, or soldered,
should be used.
4. Double check all wiring before proceeding.
5. Wire the A.C. power line cord to 115 or 230 volts.
6. Pilot light will light to show that the charger has power.

3
170 Cherry Avenue
West Sayville, NY 11796
www.kussmaul.com
Ph: 800-346-0857
Fax: [phone]
[email protected]
INSTALLATION WIRING DIAGRAM
IMPORTANT: Charger output wire size is 14 awg. Wire size is for a maximum length of 20 feet.
If wiring is to be longer, larger wiring is required. Additional information is available on request.
115 or 230 voltage se-
lector switch.
NOTE:
Do not apply 230 volts to
the charger with the se-
lector switch in the 115
volt position serious dam-
age may result
FUSE
3 AMP
POWER
INPUT
OUTPUT
L N
BAT 1 BAT 2
REMOTE
Chassis
Ground
Chassis
Ground
Chassis
Ground
Line
Neutral
Ground
A.C.Input Power
091-11-102-XX
RED
YE
B
LLOW
LACK
Optional Bar-graph
Indicator
091-11-127
Optional
Economy
Indicator

170 Cherry Avenue
West Sayville, NY 11796
www.kussmaul.com
Ph: 800-346-0857
Fax: [phone]
[email protected]
4
SPECIFICATION & OUTLINE
11.375
10.375
4.375 4.375
5.50
9/32" DIA.
OUTLINE DRAWING
SPECIFICATION CHART
Model # Amps Voltage
091-11DV-6 12 6
091-11DV-12 12 12
091-11DV-24 6 24
091-11DV-POS 12 12
SPECIFICATIONS:
Input: 115V or 230V 50/60Hz,
2 amps, switch selectable
Output: see chart
Output Current: see chart
Charge Indicator: 0-15 amps 5%
Weight: 12 lbs

5
170 Cherry Avenue
West Sayville, NY 11796
www.kussmaul.com
Ph: 800-346-0857
Fax: [phone]
[email protected]
All products of Kussmaul Electronics Company Inc. are warranted to be free of
defects of material or workmanship. Liability is limited to repairing or replacing
at our factory, without charge, any material or defects which become apparent in
normal use within 3 years from the date the equipment was shipped. Equipment
is to be returned, shipping charges prepaid and will be returned, after repair,
shipping charges paid.
Kussmaul Electronics Company, Inc. shall have no liability for damages of any
kind to associated equipment arising from the installation and/or use of the Kuss-
maul Electronics Company, Inc. products. The purchaser, by the acceptance of
the equipment, assumes all liability for any damages which may result from its
installation, use or misuse, by the purchaser, his or its employees or others.
WARRANTY POLICY
DATE INSTALLED _______________________________________________________
INSTALLED BY _________________________________________________________
VEHICLE IDENTIFICATION _______________________________________________
VEHICLE OWNER _______________________________________________________
INSTALLATION RECORD