KUSSMAUL 091-118 User manual

1
INSTRUCTION MANUAL
EURO CHARGER III
AUTOMATIC BATTERY CHARGER
MODEL #091-118-XX
TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone]
3 YEAR WARRANTY
NOTE :
This charger is designed for vehicles with
3 batteries and negative ground.
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
file:091-118.p65
1-6-00

2
INTRODUCTION
TheEuroChargerIIIBatteryChargerisacompactcompletelyautomaticchargerdesigned
for installation on vehicles with three batteries. Three individual chargers are provided to
chargethethreebatteries. Voltageissensedseparatelyforeachbatterysothateachbattery
is charged according to its requirements. The total output to the three batteries is 20
amperes. An ammeter provides continuous indication of the charger output.
ConstructionoftheEuroChargerIIIisextremelyruggedtowithstandtheshockandvibration
normally encountered by vehicle mounted equipment. The unit operates completely
automatically and stops charging the batteries when they are fully charged. There is no
trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic
loads on the battery such as radio, lights, etc., are automatically supplied with current by
the charger.
INSTALLATION
The Euro Charger III Automatic Battery Charger should be installed in an area with
adequate ventilation.
1. Mount the charger using the four holes provided for this.
2. Connect the wiring from the batteries to the Output Terminal Strip.
3. Connect the wiring to the batteries. Ring lugs that have been securely crimped, or
soldered, should be used.
4. Double check all wiring before proceeding.
5. Verify that the dual voltage switch (DV switch) on the front panel corresponds to the
applied voltage.
6. Wire the A.C. power to power input terminal strip.
7. Pilot light will light to show that the charger has power.

3
INSTALLATION WIRING DIAGRAM
IMPORTANT: Charger output wire size is 12 awg. Wire size is for a maximum length of 20
feet. If wiring is to be longer, larger wiring is required. Additional information is available on
request.
FUSE
POWER
INPUT
OUTPUT
LN
+++
BAT 1 BAT 2 BAT 3
Chassis
Ground
Chassis
Ground
Chassis
Ground
Chassis
Ground
A.C. Input Power
Line
Neutral
Ground
230
CAUTION
Be certain
that DV switch
corresponds
to input
voltage

4
SPECIFICATIONS:
Input: see chart
Output: see chart
Output Current: see chart
Charge Indicator: 0-20 amps 5%
Weight: 22 lbs
SPECIFICATION & OUTLINE
AUTO CHARGE
4.25
12.75
4.75
6.75
OUTLINEDRAWING
9/32" DIA. 4 HOLES
12.00
Model # OutputCurrent Output Voltage Input Voltage InputCurrent Charge Indicator
091-118-12 18 Amps 12 230/115,50/60Hz 2.4/4.7 Amps 25amps
091-118-24 9 Amps 24 230/115,50/60Hz 2.4/4.7 Amps 15amps

5
INSTALLATION RECORD & WARRANTY
Date Installed
Installed By
Vehicle Identification
Vehicle Owner
WARRANTY
AllproductsofKussmaulElectronicsCompanyInc.arewarrantedto be
free of defects of material or workmanship. Liability is limited to repairing or
replacing at our factory, without charge, any material or defects which
become apparent in normal use within 3 years from the date the equipment
wasshipped.Equipmentistobereturned,shippingchargesprepaidandwill
be returned, after repair, shipping charges paid.
KussmaulElectronicsCompany,Inc.shallhavenoliabilityfordamages
of any kind to associated equipment arising from the installation and /or use
ofthe KussmaulElectronics Company,Inc. products.The purchaser,by the
acceptance of the equipment, assumes all liability for any damages which
may result from its installation, use or misuse, by the purchaser, his or its
employees or others.