KUSSMAUL 091-11DV User manual

INSTRUCTION MANUAL
AUTO CHARGE 11DV
AUTOMATIC BATTERY CHARGER
MODEL #091-11DV
TEL: in NY 631 567-0314 TOLL FREE: 800 346-0857 FAX: [phone]
3 YEAR WARRANTY
NOTE :
This charger is designed for
vehicles with dual batteries
and negative ground.
INPUT :115 or 230 volt, 50/60 Hz, 2amps
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
BOOK# 091-11DV-1
OUTPUT : 11 AMPERES D.C.
rev.A: 8-30-05

INTRODUCTION
The Auto Charge 11DV Battery Charger is a compact completely automatic charger
designed for installation on vehicles with two batteries. An internal charge divider charges
both batteries simultaneously while maintaining battery isolation. Remote sensing permits
longlinesbetweenthechargerandthebatteriesbycompensatingforthevoltagedropinthe
charging wires. An ammeter provides continuous indication of the charger output. Input
powermaybeeither115voltsor230volts.Avoltageselectorswitchisprovidedontheend
panel near the output terminal strip.
ConstructionoftheAutoCharge11isextremelyruggedtowithstandtheshockandvibration
normally encountered by vehicle mounted equipment. The unit operates completely
automatically and stops charging the batteries when they are fully charged. There is no
trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic
loadsonthebatterysuchasradio,lights,etc.,areautomaticallysuppliedwithcurrentbythe
charger.
INSTALLATION
TheAutoCharge11AutomaticBatteryChargershouldbeinstalledinanareawithadequate
ventilation. A power cord is supplied for connection to 115 or 230 volts 60 Hz.
1. Mount the charger using the four holes provided for this.
2. Connect the wiring from the batteries to the Output Terminal Strip. Spade lugs that
have been securely crimped, or soldered, should be used.
3. Connect the wiring to the batteries. Ring lugs that have been securely crimped, or
soldered, should be used.
4. Double check all wiring before proceeding.
5. Wire the A.C. power line cord to 115 or 230 volts.
6. Pilot light will light to show that the charger has power.

INSTALLATION WIRING DIAGRAM
IMPORTANT: Charger output wire size is 14 awg. Wire size is for a maximum length of 20
feet. If wiring is to be longer, larger wiring is required. Additional information is available on
request.
115 or 230 voltage se-
lector switch.
NOTE:
Donot apply230 voltsto
the charger with the se-
lector switch in the 115
voltpositionseriousdam-
age may result
FUSE
3 AMP
POWER
INPUT
OUTPUT
LN
BAT 1 BAT 2
REMOTE
Chassis
Ground
Chassis
Ground
Chassis
Ground
Line
Neutral
Ground
A.C. Input Power
Optional Economy
Indicator
Optional Bar-
g
raph
Indicator
091-11-127
091-11-102-XX
YELLOW
RED
BLACK

SPECIFICATION & OUTLINE
SPECIFICATIONS:
Input: 115V or 230V 50/60Hz,
2 amps, switch selectable
Output: see chart
Output Current: see chart
Charge Indicator: 0-15 amps 5%
Weight: 12 lbs
SPECIFICATION CHART
MODEL # AMPS VOLTAGE
091-11DV-6 12 6
091-11DV-12 12 12
091-11DV-24 6 24
091-11DV-POS 12 12
11.375
10.375
4.375 4.375
5.50
9/32" DIA.
OUTLINE DRAWING

INSTALLATION RECORD & WARRANTY
Date Installed
Installed By
Vehicle Identification
Vehicle Owner
WARRANTY
All product of Kussmaul Electronics Company Inc. are warranted to be free
of defects of material or workmanship. Liability is limited to repairing or
replacing at our factory, without charge, any material or defects which
become apparent in normal use within 3 years from the date the equipment
was shipped.
Kussmaul Electronics Company, Inc. shall have no liability for damages of
any kind to associated equipment arising from the installation and /or use of
the Kussmaul Electronics Company, Inc. products. The purchaser, by the
acceptance of the equipment, assumes all liability for any damages which
may result from its installation, use or misuse, by the purchaser, his or its
employees others.