KVM-TEC 4K Multiview Commander Original operating instructions

kvm-tec
First Aid
Extender
Video error
(stripes in the
picture)
USB is not
working
No Power
(No LED)
Check the
powerplug
Is the power
supply ok? Try
another Unit.
Try reprogramming
the Unit by using a
JTAG programmer
Contact kvm-tec
support
Are the USB
Devices plugged
in correctly?
Is the USB cable
on the Local side
plugged into the
PC?
Are the USB
Devices working
directly on the
PC?
Check if local
and remote Unit
have the same
fi rmware
Replace the USB
cable from PC to
the Local
Extender
Check if the local
or the remote
Unit is causing
the problem by
swaping fi rst the
local and than the
remote Unit to
another Unit
Contact kvm-tec
support
Check if all
cables are plug-
ged in correctly
Check if the PC is
sending a Image by
plugging in a
monitor on the
local out of the
local Unit
Check if the DDC is
set correctly (in menu
under point „O“)
Check if both
Units have the
correct fi rmware
No Video
Contact kvm-tec
support
Check if all
cables are plug-
ged in correctly
Check if the PC is
sending a Image
by plugging in a
monitor on the
local out of the
local Unit
Check if local and re-
mote Unit have the
correct fi rmware
Check if the DDC
is set correctly (in
the menu under
point „o“)
Check if the
network switch
is setup correctly
and has enough
bandwidth
Contact kvm-tec
support
Check if other units
have the same
behaviour
We are here for you to answer
your questions about installation?
Manual download www.kvm-tec.com
or
kvm-tec Installationchannel on our homepage
personally [phone]
kvm-tec Support [email protected] Phone: [phone] - 30
www.kvm-tec.com
Commander
Commander
4K Multiview
kvm-tec
Quick
Installation
Check out
our Installation
Channel:
connect collaborate communicate control
kvm-tec = C 4
Softwarefeature
for
4K Ultraline in combination
with MATRIXLINE or MAXfl ex
kvm-tec InnovationTo control and
operate
contents of different PCson just one 4
k Monitor
in a distanceup to 120 km - 74mi
can be used in a standard network
from remote/CON up to 120km/74mi

27
22 21
18
25
26
1715 16
RS232
UVX1 CON
auxusb 2.0 dp out 1 dp out 2
audio
4k displayport 1.2 kvm-extender power/status
100-240V AC
50-60Hz 24VA
red. Power
12V 2A
19 20
24 23
NetworkecableCAT(6a/7/) up to 100m
Network cable CAT(5e/6/7/) up to 150m
USB to PC
Audio from PC
DVI in from PC
DVI in from PC
DVI in from PC
DVI in from PC
Audio to
PC
USB to PC
Audio to
PC
Audio from PC
Audio from PC
USB to PC
Audio to
PC
Audio from PC
USB from PC
Audio to
PC
Audio from
microphone
Audio to speaker
USB from
Keyboard and mouse
DP to
Monitor
power plug
12V 1A power plug
12V 1A
power plug
12V 1A
power plug
12V 1A
power plug
12V 3A
power plug
100-240 VAC
Quick Installation 4K Multiview Commander local / CPU – remote/ CON
1. LOCAL Connect the UVX CON/Remote and the MX/Local Units with the power cables.
2. Now connect the USB cables to a USB jack on your PCs and connect the other ends of the USB
cables to the CPU/Local Units. Connect the Keyboards and mouse to the UVXCON/Remote Unit.
3. Connect the UVX and MX CPU/Local and the UVX and MX CON/Remote Unit with several net-
work cables to the switch.
4. Connect a PC with the „Switching manager“ program to the switch. Connect the DVI cable to the
DVI socket of the PC in the DVI socket DVI/in of the local device
5. REMOTE connect the screen on the remote side of the UVX with the DP cable.
6. Then connect to the PCs audio-out with multiple audio cables to Local Audio in.
7. Connect the audio devices to the ausio jacks on the UVX remote
And now enjoy this worldwide new feature on your 4K screen