KVM-TEC masterEASY User manual

master
Easy
FULL HD - KVM EXTENDER OVER IP
Tune in the easy KVM World
Check out
our Installation Channel:
kvm-tec
•
masterEASY
Single in
Copper/Fiber
Dual in Copper/Fiber
www.kvm-tec.com
MANUAL

kvm-tec | 3
TABLE OF CONTENT
www.kvm-tec.com
WHY KVM-TEC
1. Introduction 7
1.1 Intended use 7
1.2 Safety instructions 8
1.3TechnicalSpecications 10
1.4 About your masterEASY single copper 11
1.5 About your masterEASY dual copper 13
1.6AboutyourmasterEASYextendersingleinber 15
1.7AboutyourmasterEASYextenderdualinber 17
1.8 About your masterEASY backpanel 19
1.9AboutthestatusLED 20
2. Installation of the Extender 21
2.1 Unpacking and checking the contents 21
2.2. Mounting options 23
2.2.1 Mounting pads and rubber feet 23
2.2.2 Mounting kits (optional) 23
2.3 Installing the extender 24
2.4 Quickinstallation masterEASY single copper 25
2.5 Quickinstallation masterEASY dual in copper 26
2.6 QuickinstallationMASTERexsingleinber 27
2.7 QuickinstallationmasterEASYdualinber 28
2.8 Start up 29
CONNECT kvm-tec Extender in Matrix Switching
Systemsandyoucangoupto2000endpointsand
have a super fast switching. You can connect a wide
range of different sources (servers, operator work-
station,PC, Cameras for surveillance, video walls and
much more) and operate & control the system with
centralized management
NetworkEnvironemt;1or10Gbitbandwith
IGMPSnooping(forvideosharing)
COLLABORATE with standard network components.
kvm-tec Extender are compatible with standard
network components and all kvm-tec Extender can
collaborateinrealtimewith60HzinfullHDor4K
resolution
COMMUNICATE in your Switching System with our
kvm-tec Switching Manager Software. The local and
remote Extender are arranged in an optimized way
and the Extender status is highlighted in color. With
the kvm-tec Systems computers and servers ca be
located away from work desk into central server
room fo a high security level. The environment heat
and noise are reduced at the work station and an er-
gonomic and quiet workplace for all users is possible
CONTROL your application in a much better way
withallourin-housedevelopments,likeUSB2.0
transmission, video compression without latency,
only one cable for USB and video transmission ,zero
latency. With our unique features each user can
access multiple PC sources and can control and ope-
rate up to 16 screens with one mouse & keyboard.
Video sharing can be done seamless and a central
video wall can be integrated for sharing all informa-
tions in real time

4 | kvm-tec kvm-tec | 5
TABLE OF CONTENT TABLE OF CONTENT
2.9 Replacing the SFP module 29
2.10RemovingaCATxcable 30
2.11Removingabercable 30
2.12BestpracticeforWindows10 31
3. Extender settings 34
3.1 Using the on screen menu 34
3.2Viewingthecurrentrmwareversion 35
3.3 Features 35
3.4 Diagnosis Menu 36
3.5 DDC Menu 38
3.5.1 DDC Main (single) 39
3.5.2 DDC Second (dual) 39
3.6ExtenderSettings 40
3.6.1 Local Settings 41
3.6.2 USB Compatibility mode 42
3.6.3 USB Remote wake up 42
3.6.4 Compatibility with Linux 43
3.6.5 Bandwidth reduction 43
3.6.6VGAParameters 44
3.7 Remote Settings 45
3.7.1 Editing a keyboard layout 45
3.7.2 Editing keyboard shortcuts 46
3.7.3 USB share any key 47
3.7.4 Audio input gain 47
3.7.5 Using the power saving mode 48
3.7.6 Hiding System status menu 49
3.7.7Changekeyboardfallbackmodus 50
3.7.8 Lock menu 51
3.7.9 Mouse speed 52
3.7.10Monitorsyncstrength 53
3.8 Update 54
3.8.1 Firmware update with Switching Manager Demoversion 54
3.8.2 Firmware update with USB stick 55
3.9 Unlock an upgrade 56
3.9.1 Enable or Disable USB Memory upgrade 56
3.10Aboutthisdevice 57
4. Network Settings 58
4.1 Display Switching list 58
4.1.1 Switching Status 58
4.2Switchingfeaturesmenu 60
4.2.1 Point to Point 61
4.2.2 Matrix Switching Mode 61
4.2.3 Display the last received image „Freeze Last Image“ 61
4.2.4 USB Emulation mode 62
4.2.5 USB save feature 62

6 | kvm-tec kvm-tec | 7
TABLE OF CONTENT
4.2.6 Easy Manager On/Off 63
4.2.7 ALL In ONE - EASY Manager 64
4.2.8 more features 64
4.2.9 frontbridging 65
4.2.10SystemStatusFrontbridging 67
4.2.11 Change the Frontbridging Layout 68
4.2.12backbridging 70
4.2.13 System Status Backbridging 72
4.2.14. easy cross move - Software FEature 73
4.3 Change the local settings 74
4.3.1 Bandbreitenreduzierung 74
4.4 Remote settings 75
4.4.1 Sampling Rate settings 75
4.5PUSH/GETList 76
4.6 Connecting, disconnecting or selecting a current workplace
connected devices 77
5. Troubleshooting & First Aid 78
6.Maintance & Care 80
6.1Extendercare 80
6.2.Disposal 80
7. Warranty 81
7.1. Standard warranty 81
TABLE OF CONTENT
7.2 Extended warranty 81
8. Cable requirements 82
8.1 Requirements for CAT5e/6/7 cables 82
8.2Requirementsbercables 83
8.2.1 Multi-Mode (standard) 83
8.2.2 Single-Mode (optional) 83
9. Requirements network- switch 84
9.1 Recommended Switches 84
10. Address & phone / emails 85
11. Notes 86

kvm-tec | 9
1. introduction1. INTRODUCTION
Congratulations on the purchase of your new masterEASY KVM Extender. You have
bought a high quality extender. These instructions are part of this product. They
contain important information regarding safety, use and disposal for every user of the
masterEASY KVM Extender. Please familiarise yourself with the information within
prior to using your product. Use the product only in the manner as described and for
the areas of application as stated. When passing the product to a third party be sure to
also supply all instructions and other relevant documentation. Following proper use and
maintenance, your masterEASY KVM Extender will bring you joy for many years to come.
1.1 INTENDED USE
This product is intended to be used as a device to increase the distance that a keyboard,
monitor and mouse can be placed from a computer. This product is intended for professional
use. The product should not be used in potentially explosive environments.
The product may only be used according to the instructions as described in this manual. All
use,otherthanthatdescribedinthismanual,isseenasunintendeduse.Modicationsinthe
course of technological progress are reserved. In these user instructions the masterEASY KVM
Extender is referred to as ‘product’ or ‘extender‘. The ME/PC is referred to as the ‘local unit’
(CPU) and the ME/Monitor is referred to as the ‘remote unit‘ (CON).
1.2 SAFETY INSTRUCTIONS
WARNING! Read and understand all safety instructions.
• Followalltheinstructions.Thiswillavoidaccidents,re,explosions,electricshocksor
other hazards that may result in damage to property and/or severe or fatal injuries.
Please ensure that everyone who uses the product has read and followed these warnings
and instructions.
• Keepallsafetyinformationandinstructionsforfuturereferenceandpassthemonto
subsequent users of the product.
• Themanufacturerisnotliableforcasesofmaterialdamageorpersonalinjurycaused
by incorrect handling or non-compliance with the safety instructions. In such cases, the
warranty will be voided.
• Thisproductisnotintendedforusebypersons(includingchildren)withrestricted
physical, sensory or intellectual capability or lack of experience and/or knowledge, unless
they are supervised by a person who is responsible for their safety or provides them with
instructions on how to use the product.
• DANGER! Not for use in potentially explosive environments.
• DANGER! Be vigilant at all times, and always take care around this product. Do not use
electrical equipment if you are lacking in concentration or awareness, or are under the
inuenceofdrugs,alcoholormedication.Evenamomentofinattentivenesscanleadto
serious accidents and injuries when using electrical equipment. Check the product and
the cables for any damage before use. If there is any visible damage, a strong odour, or
excessive overheating of components unplug all the connections immediately and stop
using the product.
• DANGER! The MV-F KVM Extender is a Class 1 Laser Product 1 according to
DIN40008/ENandVDE0837.
• Iftheproductisnotinstalledandusedinaccordancewiththismanual,itmaycause
disruptive interference with radio or television reception or affect other electronic
products in residential areas.
• Useshieldedcablesonlytoconnectthecomponentsinordertoavoidsuchinterference.
Non-compliance invalidates the permission to operate this product.
• Onlythemainsadapterincludedwiththeproductshouldbeusedasthepowersupply.
Do not use other adapters.
• Priortoconnectingtothemains,makesureyourlocalmainsvoltagematchestherating
indicated on the product.
• TheproductmustbeconnectedtoapermanentandearthedACwallsocket.

10|kvm-tec kvm-tec | 11
1. introduction 1. introduction
• Protectcablesfrombeingstrained,pinchedorbuckledandplacetheminawayto
prevent people from tripping over the cord.
• Inparticular,ensuretoavoiddamagetothemainsadapter.
• Usetheproductwithasuitable,properlyinstalledandeasilyaccessiblemainspower
socket. Make sure the product can be disconnected from the power socket at all times.
• Unplugtheproductduringelectricalstormsorwhennotinuse.
• DANGER! Never touch the adapter with wet hands.
• Usetheproductwithinthespeciedperformancelimits.
• Keeptheproductawayfromammablematerialssuchascurtainsanddrapes.
• Protectthemainsadapterfromusebythirdparties(particularlychildren).Keepthe
unused mains adapter in a dry, elevated or locked location away from children.
• Donotplacetheproductnearheaters.
• Donotdroporhittheproduct.
• Unplugallconnectionsbeforecleaningtheproduct.Donotusewipesorchemicals
as these could damage the surface. Wipe the housing with a damp cloth. Electrical/
electronic parts must not be cleaned.
• Alterationstotheproductandtechnicalmodicationsarenotpermitted.
1.3 TECHNICAL SPECIFICATIONS
Type: KVM Extender (local unit and remote unit)
Model: masterEASY single and dual copper
   masterEASYsingleanddualber
Powersupplyinputvoltage: 100-240V;50/60HzAC
Power supply output: 12V; 1A (external power supply)
Power requirement: 12W VDC2A redundant pro Extender
(without connected USB devices)
Operatingtemperaturerange: 0ºCto45ºC/32°Fto113°F
Storagetemperaturerange: −25ºCto80ºC/−13°Fto176°F
Relativehumidity: max.80%(non-condensing)
Storagehumidity: max.80%(non-condensing)
Casing Material: Anodized aluminium
Dimension: 109x43x107,5mm/4.29x1.69x4,23inch
Weight:  295g/0,65lbLocal/CPU/295g/0,65lbRemote/CON
Shipmentweight: 1005g/2,21lbpersetsingle
1895 g / 4,17 lb Dual
MTBF  82820calculatedhours/10years

12 | kvm-tec kvm-tec | 13
1. introduction 1. introduction
1.4 ABOUT YOUR MASTEREASY SINGLE COPPER
Local Extender (CPU)
No. Name Function
1 dvi-in DVI connection to PC
2 dvi-in DVI connection fromPC
3 USB USB to PC
4 audio in Audio in from PC
5 audio out Audio out to PC
6 kvm-link Networkcable redundant
7 kvm-link Networkcable
8 dc connection for 12V1A power supply redundant
9 dc connection 12V1A power supply
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
1
2
3
459
67 8
Remote Extender (CON)
No. Name Function
1 DVI out DVi to monitor .
2 USB USB from keyboard and mause
3 audio in Audio in from microfon etc.
4 audio out Audio to loudspeaker
5 kvm-link connection for 12 V network cable
6 kvm-link connection for CAT5/6/7 cable redundant
7 dc connection power supply 12V1A redundant
8 dc connection power supply 12 V1A
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
12
3 4
5 6 7
8

14 | kvm-tec kvm-tec | 15
1. introduction 1. introduction
1.5 ABOUT YOUR MASTEREASY DUAL COPPER
Local Extender (CPU)
No. Name Function
1 dvi-in DVI in 2 from PC
2 dvi-main DVI connection to PC
3 USB USB to PC
4 audio in Audio Out from PC
5 audio out Audio Out to PC
6 kvm-link connection network cable
7 kvm-link connection network cablel
8 dc connection 12V1A power supply
9 dc connection 12V1A power supply
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
1367
4 9
25
8
Remote Extender (CON)
No. Name Function
1 DVI DVI to Monitor 2
2 DVI DVI to Monitor 1
3 USB USB from Keyboard and mouse
4 audio in Audio in from Microphone.
5 audio out Audio to loudspeakerr
6 kvm-link connection for 12 V networkcable
7 kvm-link connection for CAT5/6/7 cable
8 dc connection power supply 12V1A
9 dc connection power supply 12V1A
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
13
5
6 7 8
9
24

16 | kvm-tec kvm-tec | 17
1. introduction 1. introduction
1.6 ABOUT YOUR MASTEREASY EXTENDER SINGLE IN FIBER
Local Extender (CPU)
No Name Function
1 dvi-out DVI connection to monitor
2 dvi-in DVI in from PC
3 USB USB to PC
4 audio in Audio in from PC
5 audio out Audio out to PC
6 kvm-link connectionbercableredundant
7 kvm-link connectionbercable
8 dc connection power supply redundant
9 dc conenction power supply
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
1
2
36 7 8
459
Remote Extender (CON)
No. Name Function
1 DVI-out DVI to Monitor.
2 USB USB from keyboard and mouse
3 audio in Audio in from microphone
4 audio out Audio out to loudspeaker
5 kvm-link connectionbercable
6 kvm-link connectionbercableredundant
7 dc connection 12V1A powee supply redundant
8 dc connection power supply
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
12567
3 4 8

18 | kvm-tec kvm-tec | 19
1. introduction 1. introduction
1.7 ABOUT YOUR MASTEREASY EXTENDER DUAL IN FIBER
Local Extender (CPU)
No. Name FunCtion
1 dvi-in DVI in 2 from PC
2 dvi-main DVI connection from PC
3 USB USB to PC
4 audio in Audio Out from PC
5 audio out Audio Out to PC
6 kvm-link connection Fibercable redundant
7 kvm-link connectionforbercable
8 dc connection 12V1A power supply redundant
9 dc connection 12V1A power supply
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
1
2
3
4 5
678
9
Remote Extender (CON)
No. Name Function
1 DVI out DVI to Monitor .
2 USB USB from keyboard and mouse
3 kvm-link connectionforbercableredundant
4 kvm-link connectionforbercable
5 dc connection power supply 12V1A redudant
6 dc connection power supply 12V1A
7 audio out Audio to loudspeaker
8 audio in Audio in from microphone etc .
LED STATUS
yellow LINK ok
green Video ok
green blinking Video and USB activity
12
7
3 4 5
6
8

20|kvm-tec kvm-tec | 21
1. introduction 1. introduction
1.8 ABOUT YOUR MASTEREASY BACKPANEL
BACKSIDE masterEASY Single & masterEASY Dual
No. Name Function
1 LED Status display LED Status
2 Reset Button for Reset
4
12
1.9 ABOUT THE STATUS LED
The Status LED (8/15) can light red, orange or green. Table 1 shows the meaning of each colour.
Also see chapter Troubleshooting.
Normal Operation
* MX only ** Rem. Only
Meaning of LED indicators
Colour Blinking Physical
Link
Active
Connection
Video
Extended
USB
Initialisation
USB Data
Received
Identify
Command
Autoupdate
Mode
Red - Yes No No Update Failed
Red Slow No No No
Orange - Yes Yes No
Orange Fast Update in Progress
Green -Yes Yes Yes Update Succedded
Green V. fast Yes**
Red/Green V. fast Yes
Yellow - No
Yellow Slow Yes
Green -Yes
Green V. fast Yes
Main LED
RJ45 Socket
LEDs *

22 | kvm-tec kvm-tec | 23
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
kvm-tec | 22
2. INSTALLATION OF THE EXTENDER
2.1 UNPACKING AND CHECKING THE CONTENTS
Beforeusingtheproductforthersttimeitshouldbecheckedfordamage.Incaseof
damage due to transport inform the carrier immediately. Before delivery the product is
checked for its function and its operating safety.
• Makesurethatthepackagingcontainsthefollowingcontent:
masterEASY single copper
delivery content - Local (CPU)
1 x ME1 local (CPU)
1 x wall power supply 12V 1A (EU-plug or int plug))
1 x DVI - DVI cable 1,8m/5.9 ft)
1 x USB cable 1,8m/ 5.9 ft
1xVGA-DVIcable1,8m/5.9ft(opt)
2 x Audio cable 1,8m/5.9ft (opt)
delivery content - Remote (CON)
1 x ME1 remote (CON)
1 x wall power supply 12V 1A (EU-plug or int plug)
4 x rubber feet
masterEASY dual copper
delivery content - Local (CPU)
1 x ME2 local (CPU)
1 x wall power supply 12V 1A (EU-plug or int plug)
2 x DVI - DVI cable 1,8m/5.9ft
1 x USB cable 1,8m/5.9ft
2xVGA-DVIcable1,8m/5.9ft(opt)
2 x Audio cable 1,8m/5.9ft (opt)
delivery content - Remote (CON)
1 x ME2 remote (CON)
1 x wall power supply 12V 1A (EU-plug or int plug)
4 x rubber feet
Make sure that the packaging contains the following content:
masterEASY single ber
Delivery content - Local (CPU)
1 x ME1-F local (CPU)
1 x wall power supply 12V 1A (EU-plug or Int plug))
1 x DVI - DVI cable 1,8m/5.9ft
1 x USB cable 1,8m/5.9ft
1xVGA-DVIcable1,8m/5.9ft(opt)
2 x Audio cable 1,8m/5.9 ft (opt)
2xSFPModule-Multimodeupto500m/1640ftduplexLC
alternativwithSingle-Modeupto20km/12mi/ItemNr6835
4 x rubber feets
Delivery content- Remote (CON)
1 x ME1-F Remote (CON)
1 x wall power supply 12V 1A (EU-plug or INT plug)
2xSFPModuleMultimodeupto500m/1640ftduplexLC
AlternativwithSingle-Modeuptp20km/12miItemNr6831
4 x rubber feet
masterEASY dual ber
Delivery content- Local (CPU)
1 x ME2-F local (CPU)
1 x wall power supply 12V 1A (EU-plug or INT plug)
2 x DVI - DVI cable 1,8m/5.9ft
1 x USB cable 1,8m/5.9 ft
2xVGA-DVIcable1,8m/5.9ft
2 x Audio cable 1,8m/5.9ft (opt)
2xSFPModule-Multimodeupto500m/1640ft
(alternativSingle-Modeupto20km/12miItemNr6831)
4 x rubber feet
Delivery content Remote (CON)
1 x ME2 remote (CON)
1 x wall power supply 12V 1A (EU-plug or INT plug)
4 x rubber feet

24 | kvm-tec kvm-tec | 25
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
2.2. MOUNTING OPTIONS
2.2.1 MOUNTING PADS AND RUBBER FEET
The mounting pads and rubber feet can be used to hold the extenders in place and prevents
them from sliding and falling.
To attach the mounting pads or rubber feet:
1. Remove the protection layer from the mounting pads or rubber feet(G).
2. Attach the mounting pads or rubber feet(G)tothebottomtheunits.
2.2.2 MOUNTING KITS (OPTIONAL)
The following mounting kits are available:
Rackmounting RMK-EASY-F Part Nr. 6232 RMK-EASY-F
The rack mounting kit RMK-EASY- F is for mounting kvm-tec smartEASY single and dual
extenders. It consists of a19“ rack shelf and an alu-faceplate.
Rackmounting RMK- EASY- FN - T Part-Nr. 6232 RMK- EASY-FN
The rack mounting kit RMK-EASY-FN is for assembling kvm-tec smartEASY extenders. It consists
of 19“ Rack Shelf, an alu-faceplate and a power supply. For 4 Single or dual Extender in one
Rack
Under table mounting kit Part Nr 6231 UMK EASY
The Under Desk Mounting kit is for underdesk mounting of the MX extender.
Din Rail mounting Part-Nr. 6235 DINMK- EASY
The DIN rail mounting is used for space-saving installation in control cabinets or on DIN rails.
The attachment to the smartEASY Extenders is possible in several ways.
Vesa mounting Part-Nr. 6236 VH-EASY
The robust VESA mounting is used to attach an extender to a monitor with existing VESA
mounting points. The Extender becomes one unit with the monitor and saves a lot of space
and cable clutter.
.
2.3 INSTALLING THE EXTENDER
WARNING! Read and understand all safety information before installing the product.
The units can be set up to access one host computer, or to access numerous host computers.
In the case of the latter, an additional Network Switch must be installed. With a Network Switch,
each user can gain quick access to any of the required computers.
point to point connection & Matrix Switching System

26 | kvm-tec kvm-tec | 27
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
2.4 QUICKINSTALLATION MASTEREASY SINGLE COPPER
Power plug 12V 1A
Power plug
12V 1A
USB to PC
DVI in from PC
DVI to Monitor
USB from Keyboard and mouse
Quick Installation masterEASY Single local / CPU – remote / CON
1. Connect the CON / Remote and the CPU / Local Unit to the included 12V 1A power supply.
2. Now connect the USB cable to a USB port on your PC and connect the other end of the USB cable to the CPU / Local Unit.
Connect keyboard and mouse to the CON / Remote Unit.
3. Connect the CPU / Local and the CON / Remote Unit with a network cable.
4. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU Local Unit (PC-in).
5. Opt: Connect PC audio/out with the audio cable to local audio/in. Connect audio/out via the audio cable
6. Almost done! Opt: Connect the audio cable local audio/out to the PC audio/in and remote audio/out with audio cable to
the microphone
7. Ifyouareusingaswitch:Connectallendpointstotheswitch.Ensurethatallconnectionshaveabandwithof1Gbit/sec.For
videosharingthenetworkhastosupportIGMPsnooping.
HAVE FUN - your kvm-tec Extender is now in use for many years (MTBF approx 10 years)
Network cable CAT5e/6/7/ up to 150m/492ft (redundant)
DVI out to Monitor
Network cable CAT5e/6/7/ up to 150m/492ft - main link
Audio from PC
Audio to PC
Audio to speaker
Audio from microfone
Power plug
12V 1A (redundant)
Power plug 12V 1A (redundant)
2.5 QUICKINSTALLATION MASTEREASY DUAL IN COPPER
Power plug 12V 1A
Power plug
12V 1A
USB to PC
DVI in 1 from PC
DVI to Monitor 1
USB from Keyboard and mouse
Quick Installation masterEASY Dual local / CPU – remote / CON
1. Connect the CON / Remote and the CPU / Local Unit to the included 12V 1A power supply.
2. Now connect the USB cable to a USB port on your PC and connect the other end of the USB cable to the CPU / Local Unit.
Connect keyboard and mouse to the CON / Remote Unit.
3. Connect the CPU / Local and the CON / Remote Unit with a network cable.
4. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in).
5. Connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CON / Local Unit (PC-in 2).
Then connect the monitor to the CON / Remote Unit using the DVI cable.
6. Opt: Connect PC Audio out with the audio cable to local audio/in. Connect audio/out via the audio cable
7. Almost done! Opt: Connect the audio cable local audio/out to the PC audio/in and remote audio/out with audio cable to
the microphone
8. Ifyouareusingaswitch:Connectallendpointstotheswitch.Ensurethatallconnectionshaveabandwithof1Gbit/sec.
ForvideosharingthenetworkhastosupportIGMPsnooping.
HAVE FUN - your kvm-tec Extender is now in use for many years (MTBF approx 10 years)
Network cable CAT5e/6/7/ up to 150m/492ft
Power plug
12V 1A (redundant)
Network cable CAT5e/6/7/ up to 150m/492ft - main link
Audio from PC
Audio to PC
Audio to speaker
Audio from microphone
DVI in 2 from PC
DVI to Monitor 2
Power plug 12V 1A redundant

28 | kvm-tec kvm-tec | 29
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
2.6 QUICKINSTALLATION MASTERFLEX SINGLE IN FIBER
Power plug 12V 1A
Power plug
12V 1A
USB to PC
DVI in from PC
DVI to Monitor
USB from Keyboard and mouse
Quick Installation masterEASY Single Fiber local / CPU – remote / CON
1. Connect the CON / Remote and the CPU / Local Unit to the included 12V 1A power supply.
2. Now connect the USB cable to a USB port on your PC and connect the other end of the USB cable to the CPU / Local Unit.
Connect keyboard and mouse to the CON / Remote Unit.
3. Connect the CPU / Local and the CON / Remote Unit with a network cable.
4. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in).
5. Then connect the monitor with the DVI cable to the CON / Remote Unit.
6. Opt: Connect PC audio/out with the audio cable to local audio/in. Connect audio/out via the audio cable
7. Almost done Opt: Connect the audio cable local audio/out to the PC audio/in and remote audio/out with audio cable to the
microphone
8. Ifyouareusingaswitch:Connectallendpointstotheswitch.Ensurethatallconnectionshaveabandwithof1Gbit/sec.For
videosharingthenetworkhastosupportIGMPsnooping.
HAVE FUN - your kvm-tec Extender is now in use for many years (MTBF approx 10 years)
OM3-Fiber cable up to 500m/1640ft (redundant)
OM3-Fiber cable up to 500m/1640ft - main link
Audio to PC
Audio from PC
Audio from Microphone
Audio to Speaker
DVI out to Monitor
Power plug 12V 1A (redundant)
Power plug
12V 1A (redundant)
2.7 QUICKINSTALLATION MASTEREASY DUAL IN FIBER
Power plug 12V 1A
Power plug
12V 1A
USB to PC
DVI in 1 from PC
DVI to Monitor 1
USB from Keyboard and mouse
Quick Installation masterEASY Dual Fiber local / CPU – remote / CON
1. Connect the CON / Remote and the CPU / Local Unit to the included 12V 1A power supply.
2. Now connect the USB cable to a USB port on your PC and connect the other end of the USB cable to the CPU / Local Unit.
Connect keyboard and mouse to the CON / Remote Unit.
3. Connect the CPU / Local and the CON / Remote Unit with a network cable.
4. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in).
5. Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU / Local Unit (PC-in 2).
Then connect the monitor with the DVI cable to the CON / Remote Unit.
6. Connect PC audio/out with the audio cable to local audio/in. Connect audio/out via the audio cable
7. Almost done! Connect the audio cable local audio/out to the PC audio/in and remote audio/out with audio cable to the
microphone
8. Ifyouareusingaswitch:Connectallendpointstotheswitch.Ensurethatallconnectionshaveabandwithof1Gbit/sec.For
videosharingthenetworkhastosupportIGMPsnooping.
HAVE FUN - your kvm-tec Extender is now in use for many years (MTBF approx 10 years)
OM3-Fiber cable up to 500m/1640ft
OM3-Fiber cable up to 500m/1640ft - main link
Audio from PC
Audio to PC
Audio to speaker
Audio from
Microfone
DVI to Monitor 2
DVI in 2 from PC
Power plug
12V 1A (redundant)
Power plug 12V 1A (redundant)

30|kvm-tec kvm-tec | 31
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
2.8 START UP
To start up the system without switch:
1. Make sure that the two monitors and the computer are switched on.
2. If you are using a Network Switch, connect the power supply to an earthed wall socket.
3. Connect both extender power supplies (C) to an earthed wall socket. Both extenders will
start an initialisation process. The red status LED blinks a few seconds. After a few seconds
the status LED lights green. The monitor will displays your computer’s desktop or any open
applications.
2.9 REPLACING THE SFP MODULE
The masterEASy Fiber is delivered with a multimode SFP module.
To replace an SFP module with a different SFP module:
1. Remove the black dust protector from the SFP module.
2. Pull the metal latch of the SFP module forwards until it is at a right angle.
3. Replace the SFP module with the other module. Put the metal latch back in position. Only
use SFP modules from kvm-tec, or recommended by kvm-tec.
2.10 REMOVING A CATX CABLE
To remove a CATx cable:
• Pressthelatchdownandslowlypullthecableout.
2.11 REMOVING A FIBER CABLE
To remove a ber cable:
• Pressthelatchdownandslowlypullthecableout.

32 | kvm-tec kvm-tec | 33
2. INSTALLATION Of The exTeNder 2. INSTALLATION Of The exTeNder
2.12 BEST PRACTICE FOR WINDOWS 10
Disable USB Energy Savings in Windows 10

34 | kvm-tec
2. INSTALLATION Of The exTeNder
kvm-tec | 35
3. EXTENDER SETTINGS
3.1 USING THE ON SCREEN MENU
Use the monitor and keyboard to use the main menu.
To access the main menu:
1. Make sure the extenders, the monitors and the computer are switched on.
2. Press the Scroll Lockkeyonyourkeyboardquicklyvetimes.
3. If your keyboard doesn‘t have a Scroll Lock key, open the on-screen keyboard from the PC.
Select Start > Settings > Ease of Access > Keyboard.
4. The main menu appears with an overview of the sub-menus.
5 To open a sub-menu press the applicable key.
Main menu short cuts :
S Status Overview Menu Status / current Status
U Update Flash FW Firmware update
F Features Overview Overview all Features
D DDCOption DDCOptionFixeSetting1920x1080
L Local Settings Setting Local Overview
R Remote Settings Setting Remote Overview
A About Overview Overview all Upgrades
Key „ESC“ Exit

36 | kvm-tec kvm-tec | 37
3. EXTENDER sETTiNgs 3. EXTENDER sETTiNgs
3.2 VIEWING THE CURRENT FIRMWARE VERSION
Under„A“-Aboutthecurrentlyinstalledrmwareversionoftheremote(CON)andlocal(CPU)
Extender is displayed (e.g. ‚4267‘)
Youwillndthescreenshotinmenuitem3.10
3.3 FEATURES
By pressing the F button the Fatures menu is displayed
Features Menu
The individual menu items are described in more detail in chapter 4 (page 52).
3.4 DIAGNOSIS MENU
In the Diagnosis menu, the runtimes of the individual connected channels are displayed. Both
Remote Unit and Partner Local Unit are listed.
Additionally you get the CPU temperature information of both units.
Another feature is the cable test

38 | kvm-tec kvm-tec | 39
3. EXTENDER sETTiNgs 3. EXTENDER sETTiNgs
As soon as a connection to the partner has been established, the test can be started with the
„Enter“ key or the arrow key on the right „→“.
After a valid synchronization process, the test is started and the test run time and errors are
displayed.
The test can be ended at any time by pressing the “Enter” or “→” key. If no error has occurred,
the status reports: “Test OK! If errors occurred during the test, the status displays the sum of all
errors that occurred.
3.5 DDC MENU
The DDC Information menu allows the user to specify which DDC information is used by the PC.
DenitionoftheDDCinformationusedbythePC:
1. make sure that the main menu is open.
Press the O button and the DDC option menu will be displayed.
-Press0todisplaytheDDCinformationofthemonitorconnectedtotheremote(CON)
Extender is connected.
- Press 2 to save the current DDC information. The system will
applies the same settings after restarting the Extender
-Pressthekeys3to8touseapredenedresolution,which
is saved.
3. press ESC to return to the main menu