KW Cages 3690 User manual

THE
APARTMENT
CAGE
RStep by Step Instructions
3690 (12) Hole Apartment Cage
3691 (8) Hole Apartment Cage

RApartment Cage Parts List
Description
Quantity
3690 (12 Hole)
Quantity
3691 (8 Hole)
Cage Front/Floor/Back Subassembly
(with pre-hung doors)
4 4
Cage Top 4 4
Cage Feet 8 8
Cage Partition Subassembly 8 4
Side Deflector 8 8
Back Deflector Guard 12 8
Plastic Door Guard 48 32
Welded Leg Frame 2 2
Frame Cross Member 2 2
Refuse Pan 12 8
3” x 3” Wire Tray Stop 12 8
Screws 12 12
Hat Nut 12 12
Bag, Cage Clips 1 1
Instruction Manual 1 1

RCage Assembly Overview

Attach Cage Ends
Attach Partitions
1
2
Swing the cage front and
back in to position as shown.
Attach the cage ends (with
L-shaped “feet” toward the
ground). Place a cage clip
into a pair of cage clip pliers
with the open part of the clip
facing outward. Hook the
two wires you wish to join in
the small part of the “J” and
squeeze the pliers to make a
connection. Clips should be
placed in each corner, then
spaced out every 4 inches.
Place the partitions in to di-
vide the cage. The deflector
angles should be touching
the cage floor. Using clip pli-
ers apply clips on all 4 sides
using the slots provided.
Turn the cage over to access
the bottom. If you have cage
ring pliers, use cage rings
in bottom four slots. As an
alternative, plastic cable ties
are furnished for the bottom
hard-to-reach holes to make
atatchment easier.

Attach Side Deflectors
Attach Back Deflectors
3
4
Place the side deflectors
inside the cage so that the
beveled edge slopes toward
and touches the floor. Use
one cage clip in each slot
to fasten. Once fastened,
be sure deflector is pressed
fall against wall and in each
corner before proceeding.
Similarly position and attach
the back deflectors using one
clip in each slot.

Attach Cage Top
Attach Subfloor
5
6
Lay the cage top in place
so that the wires spaced 1”
apart are facing upwards.
Use one clip in each cor-
ner and then space clips
out every 4 inches around
perimeter.
This is a good time to snap
the pastic door guards over
the edges of the door open-
ing.
Attach the subfloor so that
it spans between each cage
foot. Be sure the wires
spaced 1” apart are facing
up. Clip the subfloor to each
cage foot using one clip
every four inches.
Note: The subfloor is at-
tached to the base unit
only.
Slide in the individual pans
and the first level is com-
plete!
Repeat steps 1-5 for the
remaining 3 levels.

Setup Cage Frame
7
Place frame cross members
between welded leg frames.
The cross members will
slide over the protrusions on
each leg base. It is okay to
tap on ends using a hammer.
Allow extra space for cage
to fit between legs. It is pos-
sible to tap on frames with
a hammer afterwards for a
snug fit.
Position cage so that it rests
in cage frame. Adjust frame
accordingly. Using the 12
furnished screws and hat
nuts, bolt the cage to frame
uprights as shown. The hat
nut is placed inside the cage
and grips the cage wire. You
will need to remove the pans
temporarily to access the
bottom holes.
If you have ordered an op-
tional caster wheel kit, insert
the wheels posts into the
frame uprights at this time.
X12
X12
Bolt frame to base cage.
8

Stacking Units
9
Begin stacking by placing
the second level on top of
the first. Once aligned use
a cage clip at the front and
rear corners where the cage
feet rest to securely fasten.
Use two clips at each corner,
8 clips total.
Repeat for each subsequent
level.
To prevent pans from push-
ing in too far, attach the pan
stops in the gap at the rear
of each pan. The stop should
be clipped at the far left and
right sides. If there is a cen-
ter pan, the stop is placed in
the center.