Kyocera TASKalfa 306ci User manual

TASKalfa 306ci
TASKalfa 356ci
TASKalfa 406ci
PF-5120/5130/5140
DP-5100/5110
AK-5100/JS-5100
DF-5100/5110/5120
PH-5100/5110/MT-5100
FAX System 10/11
SERVICE
MANUAL
Published in February 2016
842R4114
2R4SM064
Rev.4

2R4/2R5/2R6
6-1
6 Maintenance mode
6-1 Maintenance mode
The machine is equipped with a maintenance function which can be used to maintain and service the
machine.
(1) Executing the maintenance mode
Enter “10871087” using
the numeric keys.
Enter the maintenance item
number using the [▲] [▼] keys
or numeric keys.
The selected maintenance item is run.
Press the stop key.
Press the start key.
Start
End
Maintenance mode is entered.
The maintenance item is selected.
Maintenance mode is exited.
Repeat the same
maintenance item?
Run another maintenance
item?
No
No
Yes
Yes
Enter 001 using the [▲] [▼] keys
or numeric keys
and press the start key.

2R4/2R5/2R6-2
6-2
(2) Maintenance modes list (30ppm model)
Section No. Maintenance item Outline
General U000 Printing Maintenance Report Printing the reports and exporting them to a
USB memory
U001 Exiting the maintenance mode Exiting from the maintenance mode
U002 Set Factory Default Initializing to the factory-default setting
U004 Machine serial number Display of the machine serial number and set-
ting
U010 Setting the maintenance mode ID Setting the maintenance mode ID
U019 Firmware Version Displays the firmware version of the PWB
Initializa-
tion
U021 Initializes Memory Initializing the backup RAM
U025 Firmware update (S) Updates the firmware
Drive
Paper
feed
Convey-
ing
Cooling
U030 Motor operation check Drive the drive motor
U031 Check the conveying switch Check the conveying switch On/Off
U032 Clutch operation check Check the paper conveying clutch operation
U033 Solenoid operation check Drive the paper conveying and toner supply
solenoids
U034 Paper timing adjustment Adjusting the leading edge timing and the center
line
U035 Folio size setting Sets the Folio paper length and width.
U037 Fan motor operation check Drive each fan motor.
U051 Registration paper loop amount
adjustment
Adjusts the paper loop amount between the roll-
ers
U053 Adjusting the motor speed Sets each motor's speed correction
U059 Fan mode setting Sets the drive mode of the conveying fan motor
Optical U065 Adjusting the magnification for table
scanning
Adjusting the magnification for table scanning
U066 Adjusting the table scanning timing Adjusting the leading edge timing for table scan-
ning
U067 Adjusting the table scanning center
line
Adjusting the center line for table scanning
U068 DP scanning position adjustment Adjusting the starting position for DP scanning
U070 DP magnification adjustment Adjusting the magnification for DP scanning
U071 Adjusting the DP leading edge Tim-
ing
Adjusting the DP scanning timing
U072 Adjusting the DP original center Adjusting the center line for DP scanning
U089 MIP-PG pattern output Output MIP-PG pattern

2R4/2R5/2R6
6-3
High volt-
age sys-
tem
U100 Main high voltage adjustment Adjust the drum surface potential
U101 Primary transfer voltage adjustment Sets high voltage except the main high voltage
and outputs
U106 Secondary transfer voltage adjust-
ment
Set the secondary transfer voltage correction
U107 Primary transfer cleaning voltage
adjustment
Set the primary transfer belt cleaning voltage
U110 Drum counter Displays/sets the drum counter
U117 Drum unit number Displays the drum number
U118 Drum unit history Displays the drum history
U119 Setting the drum Sets the initial LSU light intensity
U120 Drum drive distance counter Displays the drum drive distance counter
U127 Clearing the transfer count Displaying the counts
U128 Leading edge timing Adjust the transfer high-voltage output ON/OFF
timing
Devel-
oper sys-
tem
U132 Forcible toner supply operation Execute the toner supply in the toner control
level
U135 Checking the toner motor operation Drives the toner motor
U136 Toner level detection setting Sets the number of pages printable at toner near
end
U139 Temperature, humidity Displays the machine inside and outside humid-
ity
U140 Developer bias adjustment Adjust the developer bias values or set the high
altitude mode.
U147 Setting the toner applying mode Sets the overcharge toner removal mode
U148 Drum refresh mode setting Setting auto drum refresh
U155 Toner sensor output Displays the toner sensor output
U156 Toner control level adjustment Displays/adjusts the toner supply level
U157 Developer drive time Displays/sets the developer drive time
U158 Developer counter Displays/sets the developer counter
Fuser U161 Fuser temperature adjustment Sets the fuser control temperature
U167 Clearing the fuser count Displaying/clearing the counts
U199 Fuser temperature Monitor the fuser temperature
Section No. Maintenance item Outline

2R4/2R5/2R6
6-4
Opera-
tion sec-
tion
/
Support
equip-
ment
U200 All LEDs lighting Light all the LEDs on the operation panel
U201 Initializing the touch panel Correct the X and Y axis position of the touch
panel
U203 Check DP operation Checking the DP paper conveying operation
with the DP alone
U207 Operation key check Check the operation panel key operation
U211 Enhancement unit connection set-
ting
Sets the connection of the enhancement units
U221 USB host lock function setting Sets USB Host lock function ON/OFF
U222 Setting the IC card type Sets the ID card type
U223 Operation panel lock Set On/Off of the operation unit lock
U230 Optional device serial number Displays the optional device serial number
U240 Finisher operation check Checks the drive operation
U241 Finisher switch check Check the switch operation
U243 Checking the DP motor Drive the PF motor and solenoid
U244 DP switch check Drive the DP sensor
U246 Finisher adjustment Sets the finisher adjustment value
U247 Paper feed operation check Drives the PF motor and clutch
Mode
Setting
U250 Checking/clearing the maintenance
cycle
Changes the preset value
U251 Checking/clearing the maintenance
counter
Displaying/clearing/changing the counter value
U252 Destination Sets the machine operation and indication
depending on the specification of the destination
U253 Switching the double/single counts Sets the counter by color mode
U260 Switching the timing for copy count-
ing
Setting the count-up timing
U265 Setting by destination Sets the OEM code
U276 Switching the copy count mode Set the single color copy count mode
U278 Delivery date setting Register Delivery Date
U284 Setting the 2-color copy Switches the 2-color copy mode
U285 Set Service Status Page Setting the print coverage report output
U290 Setting the drive to save the HyPAS
application
Sets the drive to save the HyPAS application
U323 Abnormal temperature and humidity
notification setting
Switches the indication mode of the abnormal
temperature and humidity detection
U325 Paper interval setting Sets the print interval at high coverage
U326 Black line cleaning indication Switch the black line cleaning guidance indica-
tion
U327 Cassette heater On/Off setting Selects the cassette heater control setting
Section No. Maintenance item Outline

2R4/2R5/2R6
6-5
Mode
Setting
U332 Adjusting the black coverage coeffi-
cient
Setting the coefficient of the custom size
U341 Printer cassette setting Sets the cassette to printer output only
U343 Duplex priority mode Switches the duplex printing priority mode
U345 Setting the value for maintenance
due indication
Setting the maintenance timing display
U346 Selecting Sleep Mode Setting the BAM related sleep mode
Image
process-
ing
U402 Adjusting the printing margins Adjusts the scan image margins
U403 Adjusting margins for scanning an
original on the contact glass
Adjusts the margin for scanning originals
U404 Adjusting margins for scanning an
original from the document proces-
sor
Adjusts the margin for scanning originals
U407 Adjusting the writing timing (Duplex/
Reversal)
Adjusting the writing timing when duplex printing
U410 Adjusting the halftone automatically Acquiring the data for the automatic halftone
adjustment and the ID correction
U411 Scanner auto adjustment Adjusting the scanner and DP automatically
U425 Set Target Inputs the Lab value printed on an adjustment
original
U429 Adjusting the color balance offset Adjusts the color balance offset
U464 ID correction setting Sets the ID correction
U465 ID correction data Displays the light intensity control value after the
ID correction
U467 Color registration correction opera-
tion setting
Sets the color registration correction
U468 Color registration correction data Displays the color registration correction data
U469 Color registration adjustment Corrects the color registration
U470 Setting the JPEG compression rate Sets the JPEG compression rate
Image
process-
ing
U474 Checking the LSU cleaning Sets the LSU cleaning operation check and
cleaning cycle
U485 Image process mode setting Sets the image processing
U486 Color/BW mode setting Sets the image processing
U520 TDRS setting Checking/setting the TDRS
Section No. Maintenance item Outline

2R4/2R5/2R6
6-6
FAX U600 Initialize: All Data Initializes all data and image memory.
U601 Initialize: Keep data Initializing the software switches of other than
the machine data
U603 User data 1 Makes user settings to enable the use as a FAX
U604 User data 2 Makes user settings to enable the use as a FAX
U605 Data clear Initializing the FAX communication data
U610 System 1 Set the number of lines to be ignored when
receiving a FAX at 100% magnification and in
the auto reduction mode.
U611 System 2 Number of adjustment lines for automatic reduc-
tion.
U612 System 3 Setting regarding the FAX communication oper-
ation
U620 FAX system Sets the signal detection method for remote
switching
U625 Communication settings Sets the auto redialing interval and the number
of times of auto redialing
U630 Communication control procedures
1
Setting the FAX communication
U631 Communication control procedures
2
Sets the FAX communication
U632 Communication control procedures
3
Setting the FAX communication
U633 Communication control procedures
4
Setting the FAX communication
U634 Communication control procedures
5
Set the acceptable error when judging the
received TCF signal
U640 Communication time setting 1 Setting the detection time by remote switching
mode
U641 Communication time setting 2 Sets the time-out time for the fax communication
U650 Modem 1 Sets the G3 transmission cable equalizer
U651 Modem 2 Sets the modem output level
U660 Ring setting Setting the NCU (network control unit)
U670 List output Outputting the list of the FAX communication
data
U695 FAX function customization FAX batch transmission is set up.
U699 Software switch: Set Sets the software switches individually
Section No. Maintenance item Outline

2R4/2R5/2R6-4
6-7
Others U901 Clearing the counters by paper
source
Displays/clears the counters by paper source
U903 Clearing the jam counter Displays/clears number of occurrence by jam
trigger code
U904 Clearing the service call error coun-
ter
Displays/clears the service call error and system
error counts
U905 Optional counter Displaying the counts
U906 Resetting the partial operation Resets the partial operation
U908 Total counter Displays the FAX count
U910 Black rate data Clearing the print coverage data and its period
U911 Counter by media type Displays/clears the counts by media type
U917 Read/Write Backup Data Reading/writing the backup data to a USB mem-
ory
U920 Billing counter Displays the billing count
U927 Clearing all the billing/life counters Clearing the billing count and machine life count
U928 Machine life counter Displays the machine life count
U930 Clear the main charger roller counts Displaying/setting the counts
U952 MMaintenance mode workflow Execute the maintenance flow with the Work-
Flow data
U964 Log check Transfer the log files to a USB memory
U969 Toner area code Displays the toner area code
U977 Setting the data capture mode Stores the data sent to the main unit into a USB
memory
U984 Developer unit number Displays the developer unit number
U985 Developer unit history Displays the developer unit number history
U991 Scanner counter Displays the scanner count
Section No. Maintenance item Outline

2R4/2R5/2R6
6-8
(2-1) Content of the maintenance mode (30ppm model)
Contents
Prints the list of the current settings of the maintenance items, paper jam and service call error
occurrences. Output the event log and service status page.
Also, sends output data to a USB memory.
Purpose
Checks the current settings of the maintenance items, paper jam and service call error occur-
rences.
Before initializing or replacing the backup memory, print the list of the current settings of the
maintenance items to reenter the settings after initialization or replacement.
Method
1.Press the [Start] key.
2.Select the item to output.
3.Turn it On/Off by the [Ż] [Ź] keys.
4.Press the [Start] key.
* :Insert a USB memory into the USB memory slot to output to it.
5.Select the item to output.
6.Press the [Start] key to output the list.
* :If A4 paper is available, it is output with this size. If A4 paper is unavailable, sekect the paper
source. Output status is displayed.
* :The output data is sent to the USB memory.
Completion
Press the [Stop] key.
* :The screen for selecting a maintenance item No. is displayed.
U000 Printing Maintenance Report
(Message: Mainte Report)
Items Output list
Maintenance Maintenance mode setting list
User Status Output User Status Page
Service Status Output Service Status Page
Event Output the event log report
Network Status Output Network Status Page
All All reports output
Items Output list
Print A report is printed.
USB(Text) Destination: send to USB memory (text format)
USB(HTML) Destination: send to USB memory (HTML format)

2R4/2R5/2R6
6-9
Detail of event log
Figure 6-1
2014/10/19 15:15
[XXXXXXXX]
[XXXXXXXX] [XXXXXXXX]
Paper Jam Log Counter Log
J0000:
J0100:
J0101:
J0104:
J0105:
J0106:
J0107:
J0110:
J0111:
J0211:
J0212:
J0213:
J0501:
J0502:
J0503:
J0504:
J0508:
J0509:
J0512:
J0511:
J0513:
J0514:
J0518:
J0519:
J1403:
J1404:
J1413:
J1414:
J1604:
J1614:
J4002:
J4003:
J4004:
J4009:
J4012:
J4013:
J4014:
J4019:
J4201:
J4202:
J4203:
J4204:
0
1
11
222
1
1
1
1
1
1
1
999
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
J9200:
J9210:
J9220:
0
1
1
11
2
J4302:
J4303:
J4304:
J4309:
J9000:
0
J9004 0
1
1
1
2
J9010:
J9060:
J9061:
J9062:
2
1J9110:
J9120: 0
1
1
2
C0000:
C0001:
C0002:
C0003:
C0004:
C0005:
C0006:
C0007:
C0008:
C0009:
C0010:
C0011:
C0012:
C0013:
C0014:
C0015:
C0016:
C0017:
C0018:
C0019:
C0020:
C0021:
C0022:
C0023:
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
T00:
M00:
M02:
10
20
30
#
12
11
10
9
8
7
6
5
4
3
2
1
Count.
5555555
4444444
3333333
2222222
1111111
999999
888888
777777
666666
555555
444444
1
Event Descriprions Date and Time
0501.01.08.01.00 2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
4002.01.08.01.00
0501.01.08.01.00
4002.01.08.01.00
0501.01.08.01.00
4002.01.08.01.00
0501.01.08.01.00
4002.01.08.01
0501.01.08.01
4002.01.08.01
0501.01.08.01.00
4002.01.08.01.00
Service Call Log
#
8
7
6
5
4
3
2
1
Count.
1111111
999999
888888
777777
666666
555555
444444
1
Service Code
01.6000
01.2100
01.4000
01.6000
01.2100
01.4000
01.6000
01.2100
Maintenance Log
# Count. Item.
Unknown toner Log
#
5
4
3
2
1
Count.
1111111
999999
888888
777777
666666
Item.
01.00
01.00
01.00
01.00
01.00
Event Log
MFP
TASKalfa 406ci
Firmware version 2R6_2000.000.000 2014.09.19
[XXXXXXXXXX]
7
6
5
4
3
2
1
999999
888888
777777
666666
555555
444444
1
01.21
01.40
01.60
01.21
01.40
01.60
01.21
Data and Time
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
Data and Time
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
Data and Time
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
2014/02/12 17:30
0
1
1
J4208:
J4209:
J4211:
J4218:
0
1
1
J4212:
J4213:
11
222
J4214:
1
2
J4301:
J4219:
1
2
(2)
(4)
(3) (5)
(f)
(g)
(h)
(11)
(7)
(8)
(9)
(10)
(1)
(6)
0501.01.08.01.00
(a) (b) (c) (d) (e)