Labnet BioPette PLUS User manual

This quick guide is intended to provide
a brief overview of the main features
and operation of all Labnet Single- and
Multi-channel Pipettors.
For detailed information, please refer to
the User Manuals that can be found at
www.labnetlink.com in several languages.
Labnet Single- and Multi-
channel Pipettors
Quick Start Guide
Biopette Pro
Biopette Plus
Biopette A
Labpette FX, xed volume

Intended Use
Labnet Pipettors are volumetric instruments designed to
measure and transfer liquids precisely and safely with the
use of disposable pipet tips. The pipettors operate on the
air-cushion principle (i.e., the aspirated liquid does not
come in contact with the shaft or plunger of the pipettor).
Getting started
Know your pipettor
Pushbutton
Ejector button
Volume lock
(Biopette Plus and
Biopette Pro only)
Volume display
Tip ejector
Shaft
Multi-channel
manifold
Labpette FX, xed volume
Variable volume pipettors
Pushbutton
Ejector button
Handle
Tip ejector
Shaft
They can accommodate volumes from 0.1 µL to 10,000 µL
depending on the model. They are available in single-,
8- and 12-channel variable volume as well as xed volume
single-channel versions.

Biopette Plus Biopette A
Step 1
Set the volume
1
2
5
2
1
6
2.16 µL 1.25 mL
Biopette Pro
20.42 µL 1,000 µL
2
0
4
2
1
0
0
0
Lock the volume
Biopette Plus Biopette Pro
NOTE: Biopette A Single- and Multi-channel Pipettors do not
feature a volume lock function.
Step 2
Insert the tip
✓✕
✓✕

Ejector adjustment
Biopette Plus
Biopette A
+1 mm
+2 mm
NOTE: Ejector adjustment is not necessary in Biopette Pro
and Labpette FX pipettors as they feature a long ejector
stroke.
Pipettors 5,000 and 10,000 µL

Step 3
Aspirate the liquid
~1 sec.
Step 4
Dispense the liquid
10-40°
Recommended depth
≤1 mm 2-3 mm 2-4 mm 5-7 mm
0.1-1 µL 1-100 µL 101-1,000 µL > 1,000 µL

Step 5
Eject the tip
NOTE: Before calibration, in the Biopette Plus and Biopette
Pro lines, always remember to lock the volume using the
lock function and for the Biopette A hold the calibration
knob.
Step 6
Calibration
Biopette Plus Biopette A Labpette FX
Calibration key

Biopette Pro
Safety Notes
• The pipettor is designed for the transfer of liquids only
using the tip. Do not aspirate liquids without the tip
attached. The aspirated liquid should not enter the
pipettor, as it may cause damage.
• Single-use tips reduce the risk of contamination of
samples.
• Keep the pipettor clean, avoiding the use of abrasive or
corrosive cleaning agents (e.g., acetone).
• Keep the pipettor upright when there is liquid in the tip.
• Only using the pipettor in accordance with the
manufacturer’s instructions ensures the correct pipettor
parameters are maintained.
• After replacing the plunger or the shaft, the pipettor
should be calibrated.
• In the case of incorrect operation, the device should
be cleaned in accordance with the Instructions for Use
or transferred to a service point.
• Ambient operating temperature is +5°C to 45°C.
• Ambient storage conditions (in the original packaging
during transport and short storage) is -25°C to 55°C.
• Follow general work safety regulations regarding hazards
related to work in the laboratory.
• Take special care when pipetting aggressive substances.
• Use appropriate protective attire (e.g. clothing, goggles
and gloves).
• Avoid pointing the pipettor at yourself or others during
use.
• Only use parts and accessories recommended by the
manufacturer.
Cleaning
• External parts may be cleaned with a swab moistened
with isopropyl alcohol.
• Pipettors can be autoclaved at 121°C for 20 minutes.
Prior to autoclaving, untighten the pipettor shaft,
remove the lter from 5 and 10 mL pipettor shafts.
• The outer body of the pipettor is UV-resistant. The
recommended distance from the radiation source to
exposed element should not be less than 50 cm.
• Prolonged and very intense UV exposure can cause
de-coloration of pipettor parts but does not affect its
performance.
Warranty
Labnet Single- and Multi-channel Pipettors are covered by
a three (3) year limited warranty. For more information on
the warranty limitations refer to the full version of the User
Manuals available at www.labnetlink.com.
“Calibration”
position
“Operating”
position
Calibration key – cross end
Calibration key – flat end

© 2021 Corning Incorporated. All rights reserved.
7/21 CLSLN-AN-1007DOC REV1
Made in Poland
For a listing of trademarks, visit www.corning.com/clstrademarks.
All other trademarks are the property of their respective owners.
For additional product or technical information, visit
www.labnetlink.com or contact your local sales ofce.
NORTH AMERICA
t 800.492.1110
t 978.442.2200
ASIA/PACIFIC
Australia/New Zealand
t 61 427286832
Chinese Mainland
t 86 21 3338 4338
f 86 21 3338 4300
India
t 91 124 4604000
f 91 124 4604099
Japan
t 81 3-3586 1996
f 81 3-3586 1291
Korea
t 82 2-796-9500
f 82 2-796-9300
Singapore
t 65 6572-9740
f 65 6735-2913
Taiwan
t 886 2-2716-0338
f 886 2-2516-7500
EUROPE
[email protected]
France
t 0800 916 882
Germany
t 0800 101 1153
The Netherlands
t 020 655 79 28
United Kingdom
t 0800 376 8660
All Other European
Countries
t [phone]
LATIN AMERICA
[email protected]
Brazil
t 55 (11) 3089-7400
Mexico
t (52-81) 8158-8400