Landa Pe User manual

OPERATOR’S MANUAL

For technical assistance or the dealer nearest you consult our web page at

www.landa.com

■PE2A-1500 ■PE3-1100 ■PE4-2000 ■PE4-3000

■PE5-3000

8.913-998.0 - B (10/20)

CONTENTS

Model Number ______________________________

Serial Number ______________________________

Date of Purchase ____________________________

The model and serial numbers will be found on a decal attached

to the pressure washer.You should record both serial number and

date of purchase and keep in a safe place for future reference.

LANDA PE 8.913-998.0

Introduction.............................................................................................. 3

Important Safety Information ................................................................3-4

Component Identiﬁcation......................................................................... 5

Assembly Instructions.............................................................................. 6

Operating Instructions.............................................................................. 7

Detergents and General Operating Techniques....................................... 8

Shut Down and Clean-Up........................................................................ 9

Storage .................................................................................................... 9

Troubleshooting ................................................................................10-11

Preventative Maintenance ..................................................................... 12

Oil Change Record ................................................................................ 12

Exploded View ..................................................................................13-14

Exploded View Parts List ..................................................................15-17

Speciﬁcations....................................................................................18-19

Hose & Spray Gun ................................................................................. 20

LB Pump Exploded View and Parts List ...........................................21-22

LT Pump Exploded View and Parts List ............................................23-24

VRT3 Unloader Exploded View and Parts List....................................... 25

VBT Banjo Unloader Exploded View and Parts List .............................. 26

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

INTRODUCTION & IMPORTANT SAFETY INFORMATION

Thank you for purchasing this Pressure Washer.

We reserve the right to make changes at any time

without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of

the manufacturer’s operating instructions and warnings

before using this pressure washer.Warning information

should be emphasized and understood. If the operator

is not ﬂuent in English, the manufacturer’s instructions

and warnings shall be read to and discussed with

the operator in the operator’s native language by the

purchaser/owner, making sure that the operator com-

prehends its contents.

Owner and/or user must study and maintain for future

reference the manufacturers’ instructions.

The operator must know how to stop the machine

quickly and understand the operation of all controls.

Never permit anyone to operate the engine without

proper instructions.

SAVE THESE INSTRUCTIONS

This manual should be considered a permanent

part of the machine and should remain with it if

machine is resold.

When ordering parts, please specify model and

serial number. Use only identical replacement parts.

This machine is to be used only by trained operators.

IMPORTANT SAFETY

INFORMATION

READ OPERATOR’S

MANUAL THOROUGHLY

PRIOR TO USE.

WARNING: To reduce the risk of

injury, read operating instruc-

tions carefully before using.

1. Read the owner's manual

thoroughly. Failure to follow

instructions could cause mal-

function of the machine and

result in death, serious bodily

injury and/or property dam-

age.

2. Know how to stop the machine and bleed pressure

quickly. Be thoroughly familiar with the controls.

3. Stay alert — watch what you are doing.

4. All installations must comply with local codes.

Contact your electrician, plumber, utility company

or the selling distributor for speciﬁc details. If your

machine is rated 250 volts or less, single phase will

be provided with a ground fault circuit interrupter

(GFCI). If rated more than 250 volts, or more than

single phase this product should only be connected

to a power supply receptacle protected by a GFCI.

DANGER: Improper connection of the equipment-

grounding conductor can result in a risk of elec-

trocution. Check with a qualified electrician or

service personnel if you are in doubt as to whether

the outlet is properly grounded. Do not modify the

plug provided with the product - if it will not ﬁt the

outlet, have a proper outlet installed by a qualiﬁed

electrician. Do not use any type of adaptor with

this product

WARNING

KEEP WATER

SPRAY AWAY FROM

ELECTRICAL WIRING.

WARNING: Keep wand, hose, and

water spray away from electric

wiring or fatal electric shock may

result.

5. To protect the operator from

electrical shock, the machine

must be electrically grounded.

It is the responsibility of the

owner to connect this machine

to a UL grounded receptacle of proper voltage and

amperage ratings. Do not spray water on or near

electrical components. Do not touch machine with

wet hands or while standing in water. Always dis-

connect power before servicing.

RISK OF EXPLOSION:

DO NOT SPRAY

FLAMMABLE LIQUIDS.

WARNING

WARNING: Flammable liquids

can create fumes which can ig-

nite, causing property damage

or severe injury.

WARNING: Risk of explosion —

Do not spray ﬂammable liquids.

6. Do not allow acids,

caustic or abrasive ﬂuids to pass through the pump.

7. Never run pump dry or leave spray gun closed

longer than 1-2 minutes.

8. Keep operating area clear of all persons.

WARNING

USE PROTECTIVE

EYE WEAR

AND CLOTHING

WHEN OPERATING

THIS EQUIPMENT.

WARNING: High pressure spray

can cause paint chips or other

particles to become airborne

and ﬂy at high speeds. To avoid

personal injury, eye, hand and

foot safety devices must be

worn.

9. Eye, hand, and foot protection

must be worn when using this

equipment.

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

IMPORTANT SAFETY INFORMATION

TRIGGER GUN KICKS

BACK - HOLD WITH

BOTH HANDS

WARNING

WARNING: Grip cleaning wand

securely with both hands before

starting. Failure to do this could

result in injury from a whipping

wand.

RISK OF INJECTION

OR SEVERE INJURY

TO PERSONS. KEEP

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-

oped by these machines will

cause personal injury or equip-

ment damage. Keep clear of

nozzle. Use caution when oper-

ating. Do not direct discharge

stream at people, or severe in-

jury or death will result.

10. To reduce the risk of injury, close supervision is

necessary when a machine is used near children.

Do not allow children to operate the pressure

washer. This machine must be attended during

operation.

11. Never make adjustments on machine while in op-

eration.

12. Be certain all quick coupler ﬁttings are secured

before using pressure washer.

WARNING

PROTECT FROM

FREEZING

WARNING: Protect machine from

freezing.

13. To keep machine in best

operating conditions, it is

important you protect machine

from freezing.Failure to protect

machine from freezing could

cause malfunction of the

machine and result in death,

serious bodily injury, and/or property damage. Fol-

low storage instructions speciﬁed in this manual.

14. Inlet water must be clean fresh water and no hotter

then 90°F.

15. Manufacturer will not be liable for any changes

made to our standard machines or any components

not purchased from us.

16. The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY

FROM FALLS WHEN

USING LADDER.

WARNING: Be extremely careful

when using a ladder, scaffolding

or any other relatively unstable

location. The cleaning area

should have adequate slopes

and drainage to reduce the pos-

sibility of a fall due to slippery

surfaces.

17. Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

18. Do not operate this machine when fatigued or under

the inﬂuence of alcohol, prescription medications,

or drugs.

19. Follow the maintenance instructions

speciﬁed in the manual.

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

COMPONENT IDENTIFICATION

Pressure Nozzle

Soap

Nozzle

GFCI

Power

Supply

Power

Cord

Spray

Gun

Trigger

Start/Stop

Switches

Swivel

Connector

Inlet

Connector

Wand

Detergent

Tube

High Pressure Hose

Oil

Dipstick

Water Supply Hose

(not included)

Oil Level

Sight Glass

Detergent

Injector

Nozzle

Quick

Coupler

Detergent Bucket

(not included)

Detergent Injector - Allows you to siphon and mix

detergents.

High Pressure Hose - Connect one end to water

pump discharge nipple and the other end to spray gun.

Nozzle Quick Coupler - To easily connect the high

pressure hose and soap nozzle to wand.

Oil Level Sight Glass - A quick visual reference to

the oil level in the pump.

Pump - Develops high pressure.

Pump Protector - Cycles fresh cool water through

pump when recirculating water reaches 140°F.

Spray Gun - Must be connected to the high pressure

hose and wand.

Swivel Connector - Connects to the spray gun and

wand. Minimizes hassle of hose coiling.

Wand - Must be connected to the spray gun.

Note:If trigger on spray gun is released for more

than 1-2 minutes, water will leak from valve.Warm

water will discharge from pump protector onto

ﬂoor. This system prevents internal pump damage.

Pump Protector

Pump

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

ASSEMBLY INSTRUCTIONS

STEP 1: Attach the high pressure

hose to the spray gun using teﬂon

tape on hose threads.

STEP 3: Release the coupler collar

and push the nozzle until the collar

clicks. Pull the nozzle to make sure

it is seated properly.

STEP 5: Connect the high pres-

sure hose to the pump discharge

ﬁtting. Push coupler collar forward

until secure.

STEP 2: Pull the spring-loaded

collar of the wand coupler back

to insert your choice of pressure

nozzle.

STEP 6: Connect garden hose to

the cold water source.

STEP 7: Check inlet filters, re-

move debris, then connect the

garden hose to pump water inlet.

CAUTION: Do not run the pump

without water or pump damage

will result.

Safety

Latch

Spray

Gun

High Pressure

Hose

Wand

Coupler

Pressure

Nozzle

Pressure

Nozzle Wand

Coupler

Collar

Pump

Discharge

Fitting

High

Pressure

Hose

Cold

Water

Source

Garden

Hose

Pump

Water Inlet Garden

Hose

Coupler Collar

DipStick

STEP 4: Remove shipping cap and

install oil dipstick. Check pump oil

level by using dipstick or observe

oil level in oil window (if equipped).

Use 30 wt. (non detergent) oil.

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

OPERATING INSTRUCTIONS

STEP 1: Connect garden hose to

the cold water source and turn water

on completely. Never use hot water.

STEP 2: Trigger the spray gun to

eliminate trapped air then wait for a

steady ﬂow of water to emerge from

the spray nozzle.

Cold

Water

Source

Garden

Hose

WARNING! Never replace

nozzles without engaging

the safety latch on the spray gun

trigger.

The four color-coded quick connect nozzles provide a wide array of spray

widths from 15° to 40° and are easily accessible when placed in the con-

venient rubber nozzle holder, which is provided on the front of the machine.

NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle.

To scour the surface, select the yellow 15° nozzle. To apply detergent

select the black nozzle.

NOZZLES

Safety

Latch

STEP 3: Connect machine to ad-

equate power source. Push reset

button on GFCI.

STEP 4: Turn machine on.

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

WARNING: Some detergents

may be harmful if inhaled or in-

gested, causing severe nausea,

fainting or poisoning.The harm-

ful elements may cause property

damage or severe injury.

STEP 1: Connect detergent injector to discharge nipple

on machine, Connect high pressure hose to injector

with quick coupler. (Check to make sure locking coupler

sleeves are in proper position before applying water

pressure.)

STEP 2: Use detergent designed

speciﬁcally for pressure washers.

Prepare detergent solution as

required by the manufacturer. Fill

a container with pressure washer

detergent. Place the ﬁlter end of

detergent suction tube into the

detergent container.

STEP 3: With safety latch on

spray gun engaged, se-

cure black detergent nozzle into quick coupler.

NOTE: Detergent cannot be applied using yellow,

green or white nozzles.

STEP 4: With the engine run-

ning, pull trigger to operate

machine. Liquid detergent is

drawn into the machine and

mixed with water. Apply deter-

gent to work area. Do not allow

detergent to dry on surface.

IMPORTANT:You must ﬂush the detergent injection

system after each use by placing the suction tube

into a bucket of clean water, then run the pressure

washer in low pressure for 1-2 minutes.

THERMAL PUMP PROTECTION

If you run the engine on your pressure washer for 1-2

minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach high tempera-

tures. When the water reaches this temperature, the

pump protector engages and cools the pump by dis-

charging the warm water onto the ground.This thermal

device prevents internal damage to the pump.

CLEANING TIPS

Pre-rinse cleaning surface with fresh water. Place de-

tergent suction tube directly into cleaning solution and

apply to surface at low pressure (for best results, limit

your work area to sections approximately 6 feet square

and always apply detergent from bottom to top). Allow

detergent to remain on surface 1-3 minutes. Do not al-

low detergent to dry on surface. If surface appears to

be drying, simply wet down surface with fresh water. If

needed, use brush to remove stubborn dirt. Rinse at

high pressure from top to bottom in an even sweeping

motion keeping the spray nozzle approximately 1 foot

from cleaning surface. Use overlapping strokes as you

clean and rinse any surface. For best surface cleaning

action spray at a slight angle.

Recommendations:

• Before cleaning any surface, an inconspicuous

area should be cleaned to test spray pattern and

distance for maximum cleaning results.

• If painted surfaces are peeling or chipping, use

extreme caution as pressure washer may remove

the loose paint from the surface.

• Keep the spray nozzle a safe distance from the

surface you plan to clean. High pressure wash a

small area, then check the surface for damage. If

no damage is found, continue to pressure washing.

CAUTION - Never use:

• Bleach, chlorine products and other corrosive

chemicals

• Liquids containing solvents (i.e., paint thinner,

gasoline, oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the machine and will dam-

age the surface being cleaned.

RINSING

It will take a few seconds for the detergent to clear. Ap-

ply safety latch to spray gun. Remove black soap nozzle

from quick coupler. Select and install desired high pres-

sure nozzle. NOTE: You can also stop detergent from

ﬂowing by removing detergent siphon tube from bottle.

WARNING

DETERGENTS AND GENERAL CLEANING TECHNIQUES

Discharge

Nipple

Detergent

Injector

Quick

Coupler

Soap

Nozzle

Filter

High Pressure Hose

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

SHUTTING DOWN AND CLEAN-UP

STEP 1: Remove detergent suc-

tion tube from container and insert

into one gallon of fresh water. Slide

nozzle forward for low pressure or

to connect black detergent nozzle.

Pull trigger on spray gun and siphon

water for one minute.

STEP 2: Turn off machine. STEP 3: Turn off water

supply.

STEP 5: Disconnect the garden

hose from the water inlet on the

machine.

STEP 6: Disconnect the high

pressure hose from high pres-

sure outlet.

STEP 7: Engage

the spray gun

safety lock.

STEP 4: Press

trigger to release

water pressure.

Pump

Water

Inlet

High Pressure

Outlet

Safety

Latch

STORAGE

CAUTION

Pump Storage

CAUTION: Always store your pres-

sure washer in a location where the

temperature will not fall below 32° F

(0° C). The pump in this machine is

susceptible to permanent damage if

frozen.

FREEZE DAMAGE IS NOT COVERED BY WAR-

RANTY.

If you must store your pressure washer in a location

where the temperature is below 32° F, you can minimize

the chance of damage to your machine by draining your

machine as follows:

1. Stop the pressure washer and detach supply hose

and high pressure hose. Squeeze the trigger of the

spray gun to drain all water from the wand and

hose.

2. Restart pressure washer and let it run brieﬂy (about

5 seconds) until water no longer discharges from

the high pressure outlet.

LANDA PE 8.913-998.0

PRESSURE WASHER TROUBLESHOOTING GUIDE

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

PUMP RUNNING

NORMALLY BUT

PRESSURE LOW ON

INSTALLATION

Pump sucking air Check water supply and possibility of air

seepage.

Check valves sticking Check and clean or replace if necessary.

Unloader valve seat faulty Check and replace if necessary.

Nozzle incorrectly sized Check and replace if necessary.

Worn piston packing Check and replace if necessary.

FLUCTUATING

PRESSURE

Valves worn Check and replace if necessary.

Blockage in valve Check and clean out if necessary.

Pump sucking air Check water supply connections.

Worn piston packing Check and replace if necessary.

Insufﬁcient water Check ﬁlter and hose for breakage.

PRESSURE LOW

AFTER PERIOD OF

NORMAL USE

Nozzle worn Check and replace if necessary.

Suction or delivery valves worn Check and replace if necessary.

Suction or delivery valves

blocked

Check and clean if necessary.

Unloader valve seat worn Check and replace if necessary.

Worn piston package Check and replace if necessary.

PUMP NOISY Air in suction line Check water supply and connections on

suction line.

Broken or weak suction or deliv-

ery valve spring

Check and replace if necessary.

Foreign matter in valves Check and clean if necessary.

Worn bearings Check and replace if necessary.

Excessive temperature of water Reduce to below 140oF.

PRESENCE OF WATER

IN PUMP OIL

Oil seal worn Check and replace if necessary.

High humidity in air Check and change oil twice as often.

Piston packing worn Check and replace if necessary.

WATER DRIPPING FROM

UNDER PUMP

Piston packing worn Check and replace if necessary.

O-Ring plunger retainer worn Check and replace if necessary.

WATER DRIPPING FROM

PUMP PROTECTOR

Water supply pressure too high

(over 90 psi)

Lower water supply pressure using a

regulator.

Spray gun is in the off position for

over 5 minutes

Turn machine off if not in use for over

1-2 minutes.

OIL DRIPPING Oil seal worn Check and replace if necessary.

EXCESSIVE VIBRATION

IN HIGH-PRESSURE

HOSE

Irregular functioning of the pump

valves

Check and replace if necessary.

LANDA PE 8.913-998.0

PRESSURE WASHER TROUBLESHOOTING GUIDE

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

MOTOR WILL

NOT START

Usually caused by line trouble, such

as single phasing at the starter

Check source of power. Check overloads,

fuses, controls, etc.

MOTOR

OVERHEATING

Overload. Compare actual amps

(measured) with nameplate rating

Locate and remove source of excessive fric-

tion in motor or load.

Reduce load or replace with motor of greater

capacity.

Single phasing Check current at all phases (should be ap-

proximately equal) to isolate and correct

problem.

Improper ventilation Check external cooling fan to be sure air is

moving properly across cooling ﬁns.

Excessive dirt build-up on motor. Clean motor.

Unbalanced voltage Check voltage at all phases (should be ap-

proximately equal) to isolate and correct the

problem.

Over voltage or under voltage Check input voltage at each phase to motor.

Open stator winding Check stator resistance at all three phases for

balance.

Improper connections Inspect all electrical connections for proper

termination, clearance, mechanical strength

and electrical continuity. Refer to wiring dia-

grams.

BEARING

OVERHEATING

Misalignment Check and align motor and driven equipment.

Excessive belt tension Reduce belt tension to proper point for load.

Excessive grease in bearing Remove grease until cavity is approximately

3/4 ﬁlled.

Insufﬁcient grease in bearing Add grease until cavity is approximately 3/4

ﬁlled.

Dirt in bearing Clean bearing cavity and bearing. Repack

with correct grease until cavity is approximate-

ly 3/4 ﬁlled.

GROWLING OR

WHINING

Bad bearing Replace bearing. Clean all grease from cavity

and new bearing. Repack with correct grease

until cavity is approximately 3/4 ﬁlled.

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

PREVENTATIVE MAINTENANCE

This pressure washer was produced with the best available materials and quality craftsmanship. However, you

as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventa-

tive maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer

for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer.

Perform maintenance more often under severe conditions.

OIL CHANGE RECORD

Date Oil Changed

Month/Day/Year

Estimated Operating

Hours Since Last

Oil Change

Pump Oil

(Non foaming)

SAE 10W-40

Inspect Daily inspect the oil level

Change After ﬁrst 50 hours, then every 500 hours or annually

Replace High Pressure Nozzle Every 6 months

Replace Quick Connects Anually

Clean Water Screen/Filter Weekly

Replace HP Hose Anually if there is any sign of wear

Grease Motor Every 10,000 hours or annually

Date Oil Changed

Month/Day/Year

Estimated Operating

Hours Since Last

Oil Change

General Inspection Inspect the motor at regular intervals, approximately every 500 hours of operation,

or every 3 months, whichever occurs ﬁrst. Keep the motor clean and the ventilation

openings clear. The following steps should be performed at each inspection:

WARNING: Do not touch electrical connections before you ﬁrst ensure that power

has been disconnected. Electrical shock can cause serious or fatal injury. Only

qualiﬁed personnel should attempt the installation, operation and maintenance of

this equipment.

1. Check that the motor is clean. Check that the interior and exterior of the motor

is free of dirt, oil, grease, water, etc. Oily vapor, paper pulp, textile lint, etc.

can accumulate and block motor ventilation. If the motor is not properly

ventilated overheating can occur and cause early motor failure.

2. Check all electrical connectors to be sure that they are tight.

Lubrication & Bearings Bearing grease will lose its lubricating ability over time, not suddenly. The lubricating

ability of a grease (over time) depends primarily on the type of grease, the size of

the bearing, the speed at which the bearing operates and the severity of the oper-

ating conditions. Good results can be obtained if the following recommendations

are used in your maintenance program.

Type of Grease A high grade ball or roller bearing grease should be used. Recommended greases

for standard service conditions are: Shell Dolium R (Factory installed) or Chevron

SRI.

NOTE: Read engine manual for any maintenance or service questions.

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

EXPLODED VIEW

42,95,

96,104

100

50 49

PE4-3000A

PE3-11024

PE2A-15024

71 73

62,109

38,39

103

102

39 106

38,39

102

49 35

Model

PE3-11024

39, 77, 106

106

101

39, 106

108

107

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

HIGHPRESSURE S

EXPLODED VIEW

34 112

111

12b 13

12a

105

PE3-11024D

PE2A-15024

To Electric

Box

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY

1 8.718-835.0 Nut, Jam, ESNA, NC, 5/8" 2

2 9.802-810.0 Washer, Flat, SAE, 5/8"

(PE4-3000) 8

(All Other PE Models) 8

3 8.758-460.0 Wheel 12 In. Rim Steel 2

8.754-186.0 Qh Wheel Assy, 10"

Gray Steel Rim W/Tube 2

4 8.925-055.0 Handle, Bumper, 1-1/4",

Grey 1

5 9.198-004.0 Washer, 3/8" Uss F/w Zinc

(PE3-11024, 2A-15024) 20

(All Other PE Models) 22

6 9.802-779.0 Nut, ESNA, NC, 3/8"

(PE3-11024) 16

(All Other PE Models) 14

(2A-15024) 18

7 9.802-733.0 Bolt, 3/8" x 3-1/2", Tap 2

8 8.719-905.0 Bracket, Belt Tension 1

9 9.802-771.0 ▲Screw, 10/32” x 3/4”

(4-20024A) 3

10 8.911-293.0 Bracket, Foot, Black 1

11 8.906-774.0 Foot Assembly

(Items 11-17) 2

12a 8.718-684.0 Bolt, 3/8" x 5", NC 2

12b 9.802-817.0 Washer, 3/8" x 1", Steel 2

13 9.802-066.0 Pad, Soft Rubber 2

14 9.802-819.0 Washer, 2-1/2" x 7/16",

Flat Washer 2

15 8.719-954.0 Tube, Foot, Bolt PC 2

16 8.719-091.0 Spring, Foot, Compression 2

17 8.706-557.0 Bellows, Leg (Boot) 2

18 8.911-289.0 Frame, Black, Welded

(3-11024D, A2-15024) 1

8.911-297.0 Frame, Large, Black,

Welded (All Other Models) 1

19 8.758-290.0 Label Label Landa

W/Instruction and Warn 1

8.753-809.0 Label,Landa w/op Instr (PE2A)1

20 8.925-056.0 Grab Assy, Grey 1

21 9.802-170.0 Coupler, 3/8" Plug, Female

Steel/Zinc 1

22 9.802-171.0 Nipple, 3/4" x 3/8" Male 1

23 8.911-244.0 Bracket, Electrical Box (All

Models except 4-30024A) 1

8.911-245.0 Bracket, Electrical Box

(4-30024A) 1

24 8.932-969.0 Label, Warning Service

Cord 1

25 8.932-993.0 Cushion, Pump 2

26 Unloader, See Speciﬁcations Pages

ITEM PART NO. DESCRIPTION QTY

27 9.802-431.0 Cord, w/Gfci, 120V/20 Amp,

36' (3-11024D, 2A-15024) 1

9.802-429.0 Cord, Service 12/4

(4-20024B,C; 4-30024C;

5-30024C) 15 ft

9.802-430.0 Cord w/GFCI, 240V/30 Amp

36' (4-20024A) 1

9.802-437.0 Cord, Service,10/4

(4-30024B) 15 ft

9.802-434.0 GFCI, 240V, 40A, 1 PH, 37'

Cord (4-30024A) 1

9.802-426.0 Cord, Service, 8/4

(5-30024B) 15 ft

28 9.802-436.0 Cord, Service, SEO, 10/3 2.75 ft.

10/3 (4-20024A)

9.802-427.0 Cord Service SEO, 12/3 2 ft

(3-11024D)

9.802-429.0 Cord, Service, SEO, 12/4 2.75 ft

(4-20024B,C; 4-30024C;

5-30024C

9.802-437.0 Cord, Service, SEO, 10/4 2.75ft

9.802-425.0 Cord, Service SEO 8/3 4.66ft

(4-30024A)

9.802-426.0 Cord, Service SEO, 8/4 2.75 ft

(5-30024B)

29 9.802-518.0 Fitting, STRT, LQ Tite, Plastic

(4-20024A,B,C; 4-30024B,C;

5-30024C) 2

9.802-521.0 Strain Relief, Water Tight

(5-30024B) 1

8.752-969.0 Strain Relief 1/2", Lt, Str,

Npt 0.39-0.75 ID (2A-15024) 1

30 9.802-064.0 Grommet, Rubber, 1/8" 5

31 8.712-346.0 Nozzle, 1504 Yellow (4-30024) 1

8.712-347.0 Nozzle, 2504 Green(4-30024) 1

8.712-348.0 Nozzle, 4004 White (4-30024) 1

8.712-358.0 Nozzle, 15055 Yellow

(3-11024, 5-30024) 1

8.712-359.0 Nozzle, 25055 Green

(3-11024, 5-30024) 1

8.712-360.0 Nozzle, 4055 White

(3-11024, 5-30024) 1

8.712-362.0 Nozzle, 1506 Yellow (4-20024) 1

8.712-363.0 Nozzle, 2506 Green (4-20024) 1

8.712-364.0 Nozzle, 4006 White (4-20024) 1

8.712-334.0 Nozzle, 2503 Green

(2A-15024) 2

8.712-333.0 Nozzle, 1503, Yellow

(2A-15024) 2

LANDA PE 8.913-998.0

OPERATOR’S MANUAL

PRESSURE WASHER

EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY

32 8.712-398.0 Nozzle, Brass, Soap 1

34 8.757-203.0 Swivel, 1/2" M-NPTF x 3/4"

GHF 1

35 9.800-013.0 Label, Indoor Use 1

36 Overload, See Speciﬁcations Pages

37 Contactor, See Speciﬁcations Pages

38 9.802-759.0 Screw, 10/32" x 1/2"

(3-11024D; 4-02007A; 2A-15024) 4

(4-30024A) 7

(4-20024B,C; 4-30024B,C;

5-30024B,C) 5

39 9.802-695.0 Nut, 10/32" Keps (4-20024A,

4-20024B,C; 4-30024B,C;

5-30024B,C) 6

(2A-15024, 3-11024D) 7

(4-30024A) 10

40 8.707-254.0 Pump Protector, 3/8", PTP

(All Models Except 3-11024) 1

9.804-025.0 Pump Protector 1/4” 145°

(3-11024) 1

8.707-256.0 Pump Protector, 1/2"

(2A-15024) 1

41 Pump, See Speciﬁcations Pages

42 Motor, See Speciﬁcations Pages

43 9.802-710.0 Bolt, 5/16" x 1", NC HH

(3-11021, 2A-15024) 4

9.802-722.0 Bolt, 3/8" x 1-1/4", NC HH

(All Models Except 3-11021,

2A-15024) 4

44 8.718-980.0 Washer, 5/16" Flat

(3-11021, 2A-15024) 4

9.802-807.0 Washer, 3/8" Flat (All Models

Except 3-11021, 2A-15024) 4

45 9.802-776.0 Nut, 5/16" ESNA

(3-11021, 2A-15024) 4

9.802-779.0 Nut, 3/8" ESNA (All Models

Except 3-11021, 2A-15024) 4

46 8.718-980.0 Washer, 5/16" Flat 6

47 9.802-776.0 Nut, 5/16" ESNA, NC 3

48 8.718-674.0 Bolt, 3/8-16 X 2-1/4",GR8.2

Whiz Loc 8

49 9.802-802.0 Washer, 1/4" Flat, SAE 4

50 9.802-773.0 Nut, 1/4" ESNA, NC 2

51 8.718-618.0 Bolt, 5/16" x 3/4", NC HH 1

52 8.933-026.0 Back Plate, Belt Guard,

Large (PE4-2000) 1

8.911-285.0 Back Plate, Belt Guard,

Small (3-11024, 2A-15024) 1

8.920-582.0 Black Plate, Belt Guard,

Large (PE5-3000, PE4-3000) 1

53 8.706-655.0 Belt Guard, Small

(PE3-11024, 2A-15024) 1

8.706-656.0 Belt Guard, Large (PE) 1

54 9.802-710.0 Bolt, 5/16" x 1" NC, HH 2

ITEM PART NO. DESCRIPTION QTY

55 8.900-246.0 ▲Label, PE(Except 2A-15024) 1

56 8.900-403.0 ▲Label, 3-1100 1

8.900-409.0 ▲Label, 4-2000 1

8.900-411.0 ▲Label, 4-3000 1

8.900-414.0 ▲Label, 5-3000 1

57 Pump Bushing, See Speciﬁcations Pages

58 Motor Bushing, See Speciﬁcations Pages

59 Motor Pulley, See Speciﬁcations Pages

60 Pump Pulley, See Speciﬁcations Pages

61 Belt, See Speciﬁcations Pages

62 9.802-478.0 Lid, Plastic, Carlon (3-11024) 1

8.912-227.0 Plate, Switch Remote(2A-15024)1

63 8.716-271.0 Enclosure, Fiberglass, Nema 4X

(except 3-11024, 4-30024A) 1

9.802-476.0 Box, Plastic 10" x 8" x 6"

(4-30024A)(Except 2A-15024) 1

64 8.900-315.0 Label, OFF/ON for Push Button

(All Models Except 3-11024,

2A-15024) 1

65 9.800-016.0 Label, Disconnect

Power Supply 1

66 9.803-974.0 Switch, Green Push Button,

CH E22PB3 (All Models

Except 3-11024, 2A-15024) 1

67 9.802-535.0 Block, Contact, N/O, CH E22B2

(All Models Except 3-11024,

2A-15024) 1

68 9.803-973.0 Switch, Red Push Button, CH

E22EB2(All Models Except

3-11024, 2A-15024) 1

69 9.802-534.0 Block, Contact, N/C, CH

E22B1 (All Models Except

3-11024, 2A-15024) 1

70 9.802-457.0 Din Rail (All Models Except

(3-11024D, 2A-15024) 4"

71 9.802-477.0 Box, Electric (3-11024,2A-15024) 1

72 9.800-034.0 Label, Clear Lexan 1

73 9.802-518.0 Strain Relief, STRT, LQ Tite

Large, 3/4" (3-11024) 2

9.802-517.0 Connector, 1/2" L/T, 90 Drg 2

74 9.802-450.0 Switch, 2 Pos., 1-3 PH

(3-11024) 1

75 9.802-720.0 Bolt, 3/8" x 1", NC 4

76 9.802-789.0 Nut, 3/8" Hex NC 2

77 9.800-040.0 Label, Ground 1

78 8.706-860.0 Tee, 1/2" (4-20024,

4-30024, 5-30024, 2A-15024) 1

79 9.802-259.0 Hose, 1/2" Push-On 1.3 ft

(2A-15024, 4-20024,

4-30024, 5-30024)

80 9.802-151.0 Swivel, 1/2" JIC Fem,

Push-On (2A-15024, 4-20024,

4-30024, 5-30024) 2

LANDA PE 8.913-998.0

PRESSURE WASHER

OPERATOR’S MANUAL

EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY

81 8.757-391.0 Elbow brass 1/2 SAE (M)

x 1/2 NPTF (M) 1

(2A-15024, 4-20024,

4-30024, 5-30024)

82 8.918-424.0 Hose, 3/8" x 25", 2 Wire,

Pressure Loop (4-20024,

4-30024, 5-30024) 1

8.918-422.0 Hose, 3/8" x 20", 2 Wire,

Pressure Loop (2A-15024) 1

83 8.757-616.0 Elbow steel 1/2 JIC (M)

x 3/8 BSPP (M)

(2A-15024, 4-20024, 4-30024,

5-30024) 1

84 8.757-655.0 Adapter steel 1/2 JIC (M)

x 3/8 NPTF (M)

(4-20024, 4-30024, 5-30024) 1

8.757-935.0 Adapter steel 1/2 JIC x 3/8

NPTF (F) 90° (2A-15024) 1

85 8.757-653.0 Nipple steel hex 3/8" NPTF

x 3/8" BSPP (4-20024,

4-30024, 5-30024, 2A-15024)1

86 9.802-870.0 Block, Unloader, 3/8" x 3/8",

1.25, Steel (2A-15024,

4-20024, 4-30024, 5-30024) 1

87 8.757-262.0 Elbow brass 1/2 SAE (M)

x 3/8 NPTF (M)

(2A-15024, 4-20024, 4-30024,

5-30024) 1

88 9.802-728.0 Bolt, 3/8" x 2", NC HH

(4-20024, 4-30024,

5-30024, 2A-15024) 2

89 9.802-744.0 Bolt, 10mm x 20mm, HH

(All Models except 3-11024) 4

9.802-741.0 Bolt, 8mm x 16mm HH

(3-11024, 2A-15024) 4

90 9.802-816.0 Washer, 7/16" Lock, Split

(All Models except 3-11024) 4

9.802-814.0 Washer, 3/8", Lock, Split Ring

(3-11024, 2A-15024) 4

91 9.802-811.0 Washer, 3/8" x 1-1/2", Fender

(All Models Except 3-11024) 6

8.719-000.0 Washer, 5/16” x 1-1/4”

Fender (3-11024) 6

92 9.802-523.0 Locknut, 3/4" 2

93 9.803-098.0 Hanger, Hose & Wand 1

94 9.802-778.0 Nut, 5/16" Whiz Loc, Flange 2

95 9.802-518.0 ▲Strain Relief, Watertite

(3-11024D; 4-20024A,B,C;

4-30024B,C; ) 1

9.803-279.0 ▲Strain Relief, 1" Metal

(4-30024A, 5-30024C) 1

8.716-565.0 Strain Relief, 1" (5-30024B) 1

96 9.803-280.0 Locknut, 1"(4-30024A;

5-30024B,C) 1

97 9.802-521.0 Strain Relief, 3/4 Watertight

(4-30024A) 1

ITEM PART NO. DESCRIPTION QTY

98 9.802-518.0 Strain Relief, 3/4 Watertight

Plastic (4-30024A) 1

99 9.800-049.0 Label, Manufacturer’s

Cleaning Solution 1

100 8.757-793.0 Label Landa 50th

anniversary 1

101 9.803-032.0 Stand-Off Electrical Box

(4-30024A) 1

102 8.718-708.0 Eye Bolt, 1/4" x 1" 2

103 8.719-073.0 Spring, Pull, Belt Guard 1

104 9.800-040.0 ▲Label, Ground (Motor) 1

105 9.802-225.0 Chemical Injector Assy. 1

106 9.802-762.0 Screw, 10/32" x 1-1/4" 1

Ground

(All Models Except 3-11024D)

9.802-699.0 Screw, 10/32" x 3/4" Ground

(3-11024D) 1

107 9.802-514.0 Strain Relief 1/2", Lt, Str. Npt 3

(2A-15024)

108 8.706-733.0 Bushing, 1/2" Snap 2

(2A-15024)

109 8.900-840.0 Label, Remote Switch, 1

Home Depot (2A-15024)

111 8.756-874.0 Adapter steel 1/2 NPTF(F)

x 1/2 BSPP(M) (2A-15024) 1

112 9.804-016.0 Filter Screen Washer,

Garden Hose/30MESH

▲Not Shown

LANDA PE 8.913-998.0

PRESSURE WASHER SPECIFICATIONS

SPECIFICATIONS

PARTS SPECIFICATIONS

MOTOR

PUMP

Pump Unloader Pump Pump Pulley Pump Bushing Motor Motor Motor Motor Pulley Motor Bushing Belt Belt Contactor Overload

Model Pump Part No. Part No. Pulley Part No. Bushing Part No. Size Voltage/ph Hz Model Model Pulley Part No. Bushing Part No. Size Part No. Part No. Part No.

2A-15024D LB3030 8.923-753.0 8.754-696.0 AK74H 9.802-369.0 24MM 9.802-402.0 2HP 120V/1PH 60 2A-15024D 8.754-710.0 AK32X5/8" 9.804-004.0 N/A N/A AX35 (1) 9.803-683. 0 9.802-543.0 N/A

3-11024D LB3030 8.923-753.0 8.754-696.0 AK74H 9.802-369.0 24MM 9.802-402.0 2HP 120V/1PH 60 3-11024D 8.754-710.0 AK32X5/8" 9.804-004.0 N/A N/A AX35 (1) 9.803-683. 0 9.802-543.0 N/A

4-20024A LT6036 8.921-712.0 8.750-299.0 2AK74H 9.802-374.0 25MM 9.802-403.0 6.2HP 230V/1PH 60 4-20024A 9.802-336.0 2AK46H 8.715-547.0 HX1-1/8" 9.802-400.0 AX40 (2) 9.804-005.0 8.724-282.0 N/A

4-20024B LT6036 8.921-712.0 8.750-299.0 2AK74H 9.802-374.0 25MM 9.802-403.0 6.2HP 230V/3PH 60 4-20024B 8.751-004.0 2AK46H 8.715-547.0 HX1-1/8" 9.802-400.0 AX40 (2) 9.804-005.0 8.724-273.0 8.724-304.0

4-20024C LT6036 8.921-712.0 8.750-299.0 2AK74H 9.802-374.0 25MM 9.802-403.0 6.2HP 460V/3PH 60 4-20024C 8.751-004.0 2AK46H 8.715-547.0 HX1-1/8" 9.802-400.0 AX40 (2) 9.804-005.0 8.724-271.0 8.724-303.0

4-30024A LT6036 8.921-712.0 8.750-299.0 2BK80H 8.715-592.0 25MM 9.802-403.0 7.5HP 230V/1PH 60 4-30024A 8.715-097.0 2BK40H 9.802-384.0 HX1-3/8" 9.802-401.0 BX38 (2) 9.802-417.0 8.724-282.0 8.724-306.0

4-30024B LT6036 8.921-712.0 8.750-299.0 2BK80H 8.715-592.0 25MM 9.802-403.0 7.5HP 230V/3PH 60 4-30024B 8.755-604.0 2BK40H 9.802-384.0 HX1-3/8" 9.802-401.0 BX38 (2) 9.802-417.0 8.724-273.0 8.724-304.0

4-30024C LT6036 8.921-712.0 8.750-299.0 2BK80H 8.715-592.0 25MM 9.802-403.0 7.5HP 460V/3PH 60 4-30024C 8.755-604.0 2BK40H 9.802-384.0 HX1-3/8" 9.802-401.0 BX38 (2) 9.802-417.0 8.724-271.0 8.724-312.0

5-30024B LT6036 8.921-712.0 8.750-299.0 2BK60H 9.802-387.0 25MM 9.802-403.0 10HP 230V/3PH 60 5-30024B 8.755-605.0 2BK36H 9.802-383.0 HX1-3/8" 9.802-401.0 BX38 (2) 9.802-417.0 8.724-277.0 8.724-305.0

5-30024C LT6036 8.921-712.0 8.750-299.0 2BK60H 9.802-387.0 25MM 9.802-403.0 10HP 460V/3PH 60 5-30024C 8.755-605.0 2BK36H 9.802-383.0 HX1-3/8" 9.802-401.0 BX38 (2) 9.802-417.0 8.724-278.0 8.724-312.0

LANDA PE 8.913-998.0

PRESSURE WASHER SPECIFICATIONS

SPECIFICATIONS

MOTOR (CON'T)