Lanier Color Developer – Cyan 480-0077 Operating and maintenance instructions

your document management partner
A RICOH COMPANY
Lanier Worldwide, Inc.
2300 Parklake Drive, NE
Atlanta, GA USA 30345-
2979
Emergency Telephone: [phone]
Section 1: Chemical Product and Company Information
Identity: Color Developer –Cyan MSDS No. CP-736
Product ID: 480-0077 Issued: 06/04/2003
Synonyms
& Common
Names:
Uses:
Chemical
Formula:
Developer for Lanier LP036c
Development Unit Type 5000 Color
Cyan
Lanier LP036c
Mixture
Supersedes:
Date:
Prepared by:
Approved by:
European
Contact:
None
06/04/2003
EH&S Department 770-496-9500
Larry Choskey, Manager, CEH&S
Walter Fricke, Manager, Safety &
Environment,
Lanier Worldwide, Inc.
Im Taubental D-41468 Neuss,
Germany [phone]
Section 2: Composition / Information on Ingredients
PERCENT CAS No. EXPOSURE LIMITS SOURCE
Polyester resin > 80 Confidential Not listed N/a
Acrylic resin < 10 Confidential Not listed N/a
Silicon compound < 3 7631-86-9Not listed N/a
Organic pigment < 10 147-14-8Not listed N/a
Section 3: Hazards Identification
HMIS Rating:
FLAMMABILITY = 1 HEALTH = 1
REACTIVITY = 0 SPECIAL = none
Health Hazards, Immediate and Potential):
Primary Entry Routes:
Inhalation: Yes
Skin: No
Ingestion: No
Medical conditions aggravated by exposure: N/A
Chronic Effects:No data isavailable on this product.
Carcinogenicity: This product does not contain the carcinogenic substances, which are listed in NTP, IARC, and are regulated
by OSHA. Section 4: First Aid Measures
Inhalation: Gargle with water. Remove to fresh air if effects occur. Get medical attention if needed. Eye Contact:
In case of contact, immediately flush
eyes with water for 15 minutes. Get
medical attention if needed.
Skin Contact: Wash with soap and water. Ingestion: Dilute stomach contents with several
glasses of water. Get medical attention.
Section 5: Fire Fighting Measures
Suitable extinguishing media: CO2,dry chemical, foam or water.
Extinguishing media which may not be used for safety reasons: none
Special protective equipment for fire fighters: none
UEL: n/a LEL: n/a
MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET
Page 2 of 3CP-736
Section 6: Accidental Release Measures
Spill / leak Procedures: If spilled, sweep up using an approved toner vacuum with a 0.5 micron filter or smaller, such as the
Atrix AAA Toner Vacuum or 3M Toner Vacuum. Use of a vacuum cleaner not rated for toner particles, could result in a fire or
personal injury. Remove residue with soap and cold water.
Miscellaneous: Keep product out of sewers and watercourses.
Personal protection: Avoid inhalation of dust.
Section 7: Handling and Storage
Special Handling: Cleanse skin after contact before breaks or meals, andend of workday.
Do not handle in areas where the wind blows.
Minimize the breathing of dust.
Special Storage: Avoid direct sunlight. Keep out of reach of children. Store in a cool, dry place. Below 35C (95F)
Section 8: Exposure Control and Personal Protection Information:
Respiratory Protection: none required under normal use. Hand Protection: none required under normal use.
Eye Protection: none required under normal use. Skin Protection: none required under normal use.
Section 9: Physical and Chemical Properties
CHARACTERISTICS:
Appearance: Cyan Melting point: N/a
Form: Powder Vapor pressure: N/a
Odor: Slight plastic odor Vapor density: N/a
Solubility in Water: Insoluble Evaporation rate: N/a
Specific gravity: N/a Boiling point: N/a
Density: 1.2 g/cm3
Section 10: Stability and Reactivity
Conditions to avoid: none Materials to avoid: none Stability: Stable
Hazardous decomposition products: will not occur
Section 11: Toxicological Information:
Ames test negative Acute skin irritation: Non-irritant
Acute oral toxicity: 5000mg/kg (rat) Acute allergenic effects: non-skin sensitive
Special effects: Carcinogenicity: No data is available on this product.
Section 12: Environmental / Ecological Information
Acute toxicity to fish: not available Bioaccumulation: Not known in bioaccumulation
Persistence/Degradability: Not known Acute toxicity to daphnia:Not available
Algae inhibition test:Not available
Section 13: Disposal Consideration
Used developer should be disposed of under conditions that meet all federal, state and local environmental regulations.
Disposal regulations vary from locality to locality; therefore consult your local Lanier office or the EPA to determine the proper
method for disposal. Do not incinerate loose or spilled developer.
Section 14: Transportation Information
International regulations:
RID/ADRNot applicable ICAO-TI/ATA-DGR Not applicable
DOT 49 CFR Not applicable UN Classification Number Not applicable
ADNR Not applicable IMDG Code Not applicable
Specific precautionary transport measures: Avoid direct sunlight. Do not keep over 35?C (95?F).
Specific material to avoid: None in normal use.

MATERIAL SAFETY DATA SHEET
Page 2 of 3CP-736
Section 15: Regulatory Information
Regulation: Not known
Section 16: Miscellaneous Information
Judgment as to the suitability of information contained herein for user’s purposes is the responsibility of the purchaser.
Therefore, although reasonable care has been taken in the preparation of this information, Lanier Worldwide, Inc. extends
no warranties, makes no representations, and assumes no responsibility as to the accuracy or suitability of such
information for application to user’s intended purposes or for consequences of its use. All materials may present
unknown hazards and shouldbe used with caution. Although certain hazards are described herein, we do not guarantee
that these are the only hazards that exist.