Lanner NCA-4035 User manual

1
NCA-4035
User Manual
Version: 1.0
Date of Release: 2022-11-03
Network Appliance Platforms

NCA-4035 User Manual
2
This manual describes the overview of the various functionalities of this product, and the information you need
to get it ready for operation. It is intended for those who are:
-responsible for installing, administering and troubleshooting this system or Information Technology
professionals.
-assumed to be qualified in the servicing of computer equipment, such as professional system integrators,
or service personnel and technicians.
The latest version of this document can be found on Lanner’s official website, available either through the
product page or through the Lanner Download Center page with a login account and password.
The icons are used in the manual to serve as an indication of interest topics or important messages.
Icon
Usage
This mark indicates that there is something you should pay special
attention to while using the product.
This mark indicates that there is a caution or warning and it is
something that could damage your property or product.
To obtain additional documentation resources and software updates for your system, please visit the Lanner
Download Center. As certain categories of documents are only available to users who are logged in, please be
registered for a Lanner Account at http://www.lannerinc.com/ to access published documents and
downloadable resources.
In addition to contacting your distributor or sales representative, you could submit a request at our Lanner
Technical Support and fill in a support ticket to our technical support department.
Your feedback is valuable to us, as it will help us continue to provide you with more accurate and relevant
documentation. To provide any feedback, comments or to report an error, please email cont[email protected]m.
Thank you for your time.
This document is copyrighted © 2022 by Lanner Electronics Inc. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described in this manual at any time
without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by
any means without the prior written permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility
for its use, nor for any infringements upon the rights of third parties that may result from such use.
Note or Information
Warning or Important

NCA-4035 User Manual
3
Taiwan Corporate Headquarters
Lanner Electronics Inc.
7F, No.173, Sec.2, Datong Rd.
Xizhi District, New Taipei City 22184,
Taiwan
立端科技股份有限公司
221 新北市汐止區
大同路二段 173 號7樓
T: +886-2-8692-6060
F: +886-2-8692-6101
China
Beijing L&S Lancom Platform Tech. Co., Ltd.
Guodong LOFT 9 Layer No. 9 Huinan Road,
Huilongguan Town, Changping District, Beijing
102208 China
T: +86 010-82795600
F: +86 010-62963250
E: service@ls-china.com.cn
USA
Lanner Electronics Inc.
47790 Westinghouse Drive
Fremont, CA 94539
T: +1-855-852-6637
F: +1-510-979-0689
E: sales_us@lannerinc.com
Canada
Lanner Electronics Canada Ltd
3160A Orlando Drive
Mississauga, ON
L4V 1R5 Canada
T: +1 877-813-2132
F: +1 905-362-2369
E: sales_ca@lannerinc.com
Europe
Lanner Europe B.V.
Wilhelmina van Pruisenweg 104
2595 AN The Hague
The Netherlands
T: +31 70 701 3256
E: sales_eu@lannerinc.com

NCA-4035 User Manual
4
Intel® and Intel® Celeron® are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Follow these guidelines to ensure general safety:
Keep the chassis area clear and dust-free during and after installation.
Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your
sleeves.
Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Disconnect all power by turning off the power and unplugging the power cord before installing or removing a chassis
or working near power supplies
Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit; always check the circuit.
Suivez ces consignes pour assurer la sécuritégénérale :
Laissez la zone du châssis propre et sans poussière pendant et après l’installation.
Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre cravate ou
écharpe et remontez vos manches.
1. An unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference
to the nearby radio and television reception. It is essential that only the supplied power cord be used.
2. Use only shielded cables to connect I/O devices to this equipment.
3. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
1. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
2. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

NCA-4035 User Manual
5
Portez des lunettes de sécurité pour protéger vos yeux.
N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement dangereux.
Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon d’alimentation avant
d’installer ou de retirer un châssis ou de travailler à proximité de sources d’alimentation.
Ne travaillez pas seul si des conditions dangereuses sont présentes.
Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil génère, utilise
et émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions des fournisseurs
de composants sans fil, il risque de provoquer des interférences dans les communications radio.
There is risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Installation should be conducted only by a trained electrician or only by an electrically trained person who knows all
installation procedures and device specifications which are to be applied.
Do not carry the handle of power supplies when moving to another place.
Please conform to your local laws and regulations regarding safe disposal of lithium battery.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an
explosion.
Leaving a battery in an extremely high temperature environment can result in an explosion or the leakage of
flammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.
Jetez les piles usagées conformément aux instructions.
L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité connaissant toutes les
spécifications d’installation et d’appareil du produit.
Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.
Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable
operating temperatures without adequate circulation. Be sure that the room in which you choose to operate your
system has adequate air circulation.
Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An open chassis
permits air leaks, which may interrupt and redirect the flow of cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when
electronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow
ESD-prevention procedures when removing and replacing components to avoid these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground
yourself by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour refroidir
l’équipement à une température de fonctionnement acceptable sans circulation adaptée. Vérifiez que votre site
propose une circulation d’air adéquate.
Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de refroidissement de bien
circuler. Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et rediriger le flux d’air frais destiné aux
composants internes.
Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits électriques. Des dégâts
d’ESD surviennent lorsque des composants électroniques sont mal manipulés et peuvent causer des pannes totales
ou intermittentes. Suivez les procédures de prévention d’ESD lors du retrait et du remplacement de composants.
Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est disponible,
reliez votre corps àla terre en touchant la partie métallique du châssis.
Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et 10 mégohms
(Mohms).

NCA-4035 User Manual
6
Mounting Installation Precautions
The following should be put into consideration for rack-mount or similar mounting installations:
Do not install and/or operate this unit in any place that flammable objects are stored or used in.
The installation of this product must be performed by trained specialists; otherwise, a non-specialist might create the
risk of the system’s falling to the ground or other damages.
Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for supporting the
system or use of inappropriate installation components.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature
of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the
manufacturer.
Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow required for safe
operation of the equipment is not compromised.
Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
Reliable Grounding - Reliable grounding of rack mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Installation & Operation
This equipment must be grounded. The power cord for product should be connected to a socket-outlet with earthing
connection.
Cet équipement doit être mis à la terre. La fiche d'alimentation doit être connectée à une prise de terre correctement
câblée
Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code
and NFPA 75.
Peut être installé dans des salles de matériel de traitement de l'information conformément à l'article 645 du National
Electrical Code et àla NFPA 75.
The machine can only be used in a restricted access location and must be installed by a skilled person.
Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT.
Warning
Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired earth
ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts.
Product shall be used with Class 1 laser device modules.
Avertissement
Équipement de classe I. Ce matériel doit être relié à la terre. La fiche d’alimentation doit être raccordée à une prise de
terre correctement câblée. Une prise de courant mal câblée pourrait induire des tensions dangereuses sur des parties
métalliques accessibles.
Le produit doit être utiliséavec des modules de dispositifs laser de classe 1.

NCA-4035 User Manual
7
Before turning on the device, ground the grounding cable of the equipment. Proper grounding (grounding) is very
important to protect the equipment against the harmful effects of external noise and to reduce the risk of electrocution in
the event of a lightning strike. To uninstall the equipment, disconnect the ground wire after turning off the power. A
ground wire (green-and-yellow) is required and the part connecting the conductor must be greater than 4 mm2 or 10 AWG.
Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.
Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre les effets
néfastes du bruit externe et réduire les risques d’électrocution en cas de foudre.
Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.
Un câble de mise àla terre est requis et la zone reliant les sections du conducteur doit faire plus de 4 mm2 ou 10 AWG.
Connect the grounding cable to the ground.
The protection device for the DC power source must provide 30 A current.
This protection device must be connected to the power source before DC power.
Branchez le câble de mise à la terre àla terre.
L’appareil de protection pour la source d’alimentation CC doit fournir 30 A de courant.
Cet appareil de protection doit être branché à la source d’alimentation avant
l’alimentation CC.

NCA-4035 User Manual
8
Package Content.............................................................................................................................10
Ordering Information .....................................................................................................................10
Optional Accessories ......................................................................................................................10
System Specifications.....................................................................................................................11
Front Panel .....................................................................................................................................12
Rear Panel.......................................................................................................................................13
Block Diagram.................................................................................................................................14
Jumpers and Connectors................................................................................................................15
Opening the Chassis .......................................................................................................................29
Installing the System Memory .......................................................................................................30
Installing M.2 Memory Cards (Optional)........................................................................................32
Installing IPMI BMC Card (Optional) ..............................................................................................34
Installing TPM.................................................................................................................................35
Installing NIC Modules....................................................................................................................36
Replacing the Power Supply Units .................................................................................................37
Mounting the System.....................................................................................................................38
Overview.........................................................................................................................................44
BMC Main Features........................................................................................................................44
BMC Firmware Functional Description ..........................................................................................45

NCA-4035 User Manual
9
IPMI Commands Support List.........................................................................................................46
Using BMC Web UI .........................................................................................................................48
Wizard Welcome Page Introduction ..............................................................................................50
Web UI Layout Introduction...........................................................................................................51
Main Page.......................................................................................................................................54
Advanced........................................................................................................................................55
Platform..........................................................................................................................................75
Socket .............................................................................................................................................79
Server Mgmt...................................................................................................................................90
Security...........................................................................................................................................95
Boot Menu......................................................................................................................................98
Save and Exit Menu........................................................................................................................99
Warranty Policy ............................................................................................................................108

NCA-4035 User Manual
10
The NCA-4035 is based on Intel® Xeon D, a branch of Xeon processors optimized for delivering ultra-low
power consumption and robust performance. This appliance comes with the most innovative System-on-a-
Chip built for the edge and is ideal for applications in networking, 5G and IoT/IIoT Edge computing, delivering
improvement in packet processing performance, virtualized Customer Premise Equipment (vCPE) usages.
Your package contains the following items:
1x NCA-4035Network Security Platform
1x Power Cable
2x Console Cable
1x Short Ear Rackmount Kit (with screws)
SKU No.
Main Features
NCA-4035A
Intel® Ice Lake D HCC D2798NT, 20C, 125W CPU w/ 100G QAT; 1x GbE RJ45 Console
Port, 10x GbE RJ45 Ports w/ 2 Pairs of Bypass, 4x 10G SFP+ Ports, 1x NIC Module,
300W Redundant Power Supply
NCA-4035B
Intel® Ice Lake D HCC D-2776NT, 16C, 117W CPU w/ 100G QAT, 1x GbE RJ45 Console
Port, 10x GbE RJ45 Ports w/ 2 Pairs of Bypass, 4x 10G SFP+ Ports, 1x NIC Module,
300W Redundant Power Supply
NCA-4035C
Intel® Ice Lake D HCC D-2753NT, 12C, 87W CPU w/ 50G QAT, 1x GbE RJ45 Console
Port, 10x GbE RJ45 Ports w/ 2 Pairs of Bypass, 4x 10G SFP+ Ports, 1x NIC Module,
300W Redundant Power Supply
NCA-4035D
Intel® Ice Lake D HCC D-2733NT, 8C, 80W CPU w/ 50G QAT, 1x GbE RJ45 Console
Port, 10x GbE RJ45 Ports w/ 2 Pairs of Bypass, 4x 10G SFP+ Ports, 1x NIC Module,
300W Redundant Power Supply
NCA-4035E
Intel® Ice Lake D HCC D-2712T, 4C, 65W CPU w/ QAT, 1x GbE RJ45 Console Port, 10x
GbE RJ45 Ports w/ 2 Pairs of Bypass, 4x 10G SFP+ Ports, 1x NIC Module, 350W Single
Power Supply
Model
Description
IO-2520IXM401A
Uplayer NIC Module Kit
IAC-AST2500E
IPMI Card Kit
DC Power Supply
DC Redundant Power Supply Module
Slide Rackmount Rail Kit
1U Rackmount kit

NCA-4035 User Manual
11
Form Factor
1U 19” Rackmount
Platform
Processor Options
SKU A: Intel® D-2798NT, 20C, 125W
SKU B: Intel® D-2776NT, 16C, 117W
SKU C: Intel® D-2753NT, 12C, 87W
SKU D: Intel® D-2733NT, 8C, 80W
SKU E: Intel® D-2712T, 4C, 65W
CPU Socket
1x Onboard
Security Acceleration
Intel® QuickAssist Technology (By SKU)
BIOS
AMI SPI Flash BIOS
System Memory
Technology
DDR4 3200 MHz REG, ECC or non-ECC UDIMM/RDIMM
Max. Capacity
256GB
Socket
4x 288pin DIMM
Networking
Ethernet Ports
2x GbE RJ45 via I210-AT;
4x GbE RJ45 via I350-AM4;
4x GbE RJ45 via I350-AM4 w/ 2 pair bypass;
4x 10 SFP+
NIC Module Slot
1x NIC Module Slot
LOM
I/O Interface
1x NCSI share-link w/ i210-AT (dedicated LOM port if IPMI
card inserted)
OPMA Slot
Yes
I/O Interface
Reset Button
1x Reset Button
LED Indicator
Power/Status/Storage, refer to Appendix A
Power Button
1x ATX Power Button
Console Port
1x RJ45 Consol Port
USB Port
2x USB 3.0 Ports
Power Input
1x AC Power Inlet on PSU
Storage
Onboard Slots
1x M.2 2242 B-Key;
2x M.2 2280 B-Key
Expansion
PCIe
1x Gen4 PCI-E*8 for front NIC via 1x SlimSAS connector;
1x Gen4 PCIe*16 for Rear Standard PCIe card via 2x Slim SAS
Connector (FHHL)
Miscellaneous
Watchdog
Yes
Internal RTC with Li Battery
Yes
TPM
Yes, onboard
Cooling
Processor
Passive CPU Heatsink
System
4x Individual Cooling Fans with Smart Fan
Environmental Parameters
Temperature
0~40ºC Operating,
-20~70ºC Non-Operating
Humidity (RH)
5~90% Operating; 5~95% Non-Operating
System Dimensions
Size (WxDxH)
438 x 44 x 321mm
Weight
8.6kg
Package Dimensions
(WxDxH)
739 x 215 x 582 mm
Weight
15 kg
Power
Type/Watts
SKU A/B/C/D: 300W 1+1 Redundant PSU;
SKU E: 350W Single PSU
Input
Redundant: AC 100~240V @50~60 Hz
Single: AC 100~240V @47~63Hz
OS Support
Linux
Approvals and Compliance
CE/FCC Class A, UL, RoHS

NCA-4035 User Manual
12
No.
Description
F1
LED Indicators
Power/Status/Storage, pls refer to Appendix A
F2
Reset Button
1x Reset Button
F3
Console Port
1x RJ45 Console Port
F4
USB Port
2x USB 3.0 Ports
F5
LAN Port
1x RJ45 GbE LAN via I210-AT
F6
LOM Port
1x RJ45 GbE LOM Port
F7
LAN Port
4x RJ45 GbE LAN via I350-AM4
F8
LAN Port
4x 10G SFP+
F9
LAN Port
4x RJ45 GbE LAN via I350-AM4
F10
NIC Slot
1x NIC NCS2 Slim Module Slot
F5
F1
F3
F7
F4
F2
F8
F9
F10
F6

NCA-4035 User Manual
13
No.
Description
R1
PCIe Expansion Slot
PCIe*16 via 2x Slim SAS Connector (FHHL) (Optional)
R2
Cooling Fan
4x Cooling Fans
R3
Redundant PSU
SKU A/B/C/D : 2x 300W AC Redundant PSU (N+1 design)
SKU E : 1x 350W Single AC PSU
R4
Grounding Hole
1x Semi-shearing hole for grounding screws
R5
ESD Jack
1x Semi-shearing hole for ESD screws
R6
Power Switch
1x Slim Type ATX Power Switch
R1
R3
R4
R6
R2
R5

NCA-4035 User Manual
14
Ice Lake-D HCC
DDR4
GPIOUSB3.0
RJ-45
Console Reset Bottom
2xSATA 3.0
2x SATA3.0
I350-AM4
2x PCIEx1 1x PCIEx4
LPC
USB2.0
SIO
2nd console
USB3.0
2x M.2 2280 SATA SSD
eSPI
80 debug ports
SATA3.0
M.2 2242 SATA SSD
SPI
SPI
ROM
BIOS
BIOS
PCIe
USB
LPC
GPIO
ADC
UART
others
NCSI
I210 I210 I350-AM4
1x PCIEx4
4x10G SFP+ or 2x25G
SFP28
SlimSAS
1xPCIex16 or
2xPCIex8
4xSGMII or SFI
4 Port 1G 4x10G Maxlinear
4x2.5G
XL82788E1543
1xPCIex8
SlimSAS
Intel not support.
Lanner should request
Bypass Bypass

NCA-4035 User Manual
15
The following references the pin assignments and internal connectors of the system.

NCA-4035 User Manual
16
CMOS1: Clear CMOS
CMOS1
Description
1-2
Normal (Default)
2-3
Clear CMOS
JPWR1: External Power Button (1x2 Pin 2.43mm Wafer)
PIN
Description
1
PS_IN
2
GND
JRST1: Reset Mode Select
PIN
Description
1-2
Hardware Reset
2-3
Software Reset
JDUAL1: Select CS for Flash Fixture
Pin/Switch
Description
1-2 Short,
3-4 Short
Flash 1st SPI ROM (Default)
1-3 Short,
2-4 Short
Flash 2nd SPI ROM
J13: BIOS Boot Up / Function Select
Pin/Switch
Description
1-3 Short
Boot Up from 1st SPI ROM (Default)
3-5 Short
Boot Up from 2nd SPI ROM
Pin/Switch
Description
2-4 Short
Enable Dual BIOS (Default)
4-6 Short
Disable Dual BIOS

NCA-4035 User Manual
17
RJ1: Dual RJ-45 with LED
Pin No.
Description
Fast E-Net
Giga Net
1
TX+
MD0+
2
TX-
MD0-
3
RX+
MD1+
4
T45
MD2+
5
T45
MD2-
6
RX-
MD1-
7
T78
MD3+
8
T78
MD3-
10-/100-/1000+
10
10+/100+/1000-
11
Link+/ACT-
12
Link-/ACT+
LAN1: 2x2 Port RJ-45 with LED
Pin No.
Description
Fast E-Net
Giga Net
N1
TX+
MD0+
2
TX-
MD0-
3
RX+
MD1+
4
T45
MD2+
5
T45
MD2-
6
RX-
MD1-
7
T78
MD3+
8
T78
MD3-
10-/100-/1000+
10
10+/100+/1000-
11
Link+/ACT-
12
Link-/ACT+
LAN2: 1x4 Port RJ-45 with LED
Pin No.
Description
Fast E-Net
Giga Net
N1
TX+
MD0+
2
TX-
MD0-

NCA-4035 User Manual
18
3
RX+
MD1+
4
T45
MD2+
5
T45
MD2-
6
RX-
MD1-
7
T78
MD3+
8
T78
MD3-
10-/100-/1000+
10
10+/100+/1000-
11
Link+/ACT-
12
Link-/ACT+
SFP1/SFP2: SFP28 2x1 Assy with LED
PIN
Description
PIN
Description
1
VeeT
11
VeeR
2
TxFault
12
RD-
3
TxDis
13
RD+
4
SDA
14
VeeR
5
SCL
15
VCCR
6
MOD_ABS
16
VCCT
7
RS0
17
VeeT
8
RX_LOS
18
TD+
9
RS1
19
TD-
10
VeeR
20
VeeT
JLAN1: Minimezz Connector
PIN
Description
PIN
Description
1
5VSB
2
GND
3
NC
4
CR_RX0-
5
NC
6
CR_RX0+
7
GND
8
GND
9
CR_RX1-
10
NC
11
CR_RX1+
12
NC
13
GND
14
GND
15
NC
16
CR_RX2-
17
NC
18
CR_RX2+
19
GND
20
GND
21
CR_RX3-
22
NC
23
CR_RX3+
24
NC

NCA-4035 User Manual
19
25
GND
26
GND
27
NC
28
NC
29
NC
30
PLT_RST#
31
GND
32
3VSB
33
GND
34
GND
35
PRESNT#
36
MDIO
37
12VSB
38
12VSB
39
NC
40
MDC
41
NC
42
INT#
43
GBE_SCL
44
GBE_RST#
45
GBE_SDA
46
GND
47
NC
48
CR_TX0+
49
NC
50
CR_TX0-
51
GND
52
GND
53
CR_TX2+
54
NC
55
CR_TX2-
56
NC
57
GND
58
59
NC
60
CR_TX1+
61
NC
62
CR_TX1-
63
GND
64
GND
65
CR_TX3+
66
NC
67
CR_TX3-
68
NC
69
GND
70
GND
71
NC
72
NC
73
NC
74
NC
75
GND
76
GND
77
GND
78
GND
79
12VSB
80
12VSB

NCA-4035 User Manual
20
JUSBCOM1: USB3.0 Double Stack Type A+ Console Port Connector
PIN
Description
1
NC
2
NC
3
NC
4
GND
5
TXD
6
RXD
7
RTS
8
CTS
PIN
Description
1
USB_VCC1
2
D1-
3
D1+
4
GND
5
USB3.0_RX-
6
USB3.0_RX+
7
GND
8
USB3.0_TX-
9
USB3.0_X+
JCOM2: COM2 (Pin Header)
PIN
Description
1
DCD#
2
DSR#
3
RX
4
RTS
5
TX
6
CTS#
7
DTR
8
RI#
9
GND
This manual suits for next models
5
Table of contents
Other Lanner Network Hardware manuals

Lanner
Lanner IIOT-I330 User manual

Lanner
Lanner FX-3420 User manual

Lanner
Lanner NCA-1010 User manual

Lanner
Lanner ICS-I372 User manual

Lanner
Lanner LWR-X8460 User manual

Lanner
Lanner EAI-I130 User manual

Lanner
Lanner NCA-5210 User manual

Lanner
Lanner FW-8771 User manual

Lanner
Lanner NCA-1040SE User manual

Lanner
Lanner ECA-4027 User manual

Lanner
Lanner NCA-6530 User manual

Lanner
Lanner NCA-1525 User manual

Lanner
Lanner R6S User manual

Lanner
Lanner NCA-4112A User manual

Lanner
Lanner NCA-1516 User manual

Lanner
Lanner NCA-5710 User manual

Lanner
Lanner NCA-5230 User manual

Lanner
Lanner NCA-1040 User manual

Lanner
Lanner FX-3230 User manual

Lanner
Lanner NCA-1611A User manual