Lanner NCA-5230 User manual

NCA-5230
User Manual
Version: 1.0
Date of Release:2022-06-14
Network Appliance Platform

NCA-5230 User Manual
2
This manual describes the overview of the various functionalities of this product and the information you need to
get it ready for operation. It is intended for those who are:
-responsible for installing, administering, and troubleshooting this system or Information Technology
professionals.
-assumed to be qualified in the servicing of computer equipment, such as professional system integrators or
service personnel and technicians.
The latest version of this document can be found on Lanner’s official website, available either through the
product page or through the Lanner Download Center page with a login account and password.
This document utilizes different icons in order to make the selected text more transparent and explicable to users.
Please note that this document contains the following icons:
Icon
Usage
This mark indicates that there is something you should pay special
attention to while using the product.
This mark indicates that there is a caution or warning, and it is
something that could damage your property or product.
To obtain additional documentation resources and software updates for your system, please visit the Lanner
Download Center. As certain categories of documents are only available to users who are logged in, please be
registered for a Lanner Account at http://www.lannerinc.com/ to access published documents and
downloadable resources.
For troubleshooting the issues with your system, please check the Lanner Q&A page for a diagnostic
procedure and troubleshooting steps.
In addition to contacting your distributor or sales representative, you could submit a request to our Lanner
Technical Support page to fill in a support ticket to our technical support department.
Your feedback is valuable to us, as it will help us continue to provide you with more accurate and relevant
documentation. To provide any feedback, comments, or to report an error, please email [e-mail].
Thank you for your time.
Note or Information
Warning or Important

NCA-5230 User Manual
3
Taiwan Corporate Headquarters
Lanner Electronics Inc.
7F, No.173, Sec.2, Datong Rd.
Xizhi District, New Taipei City 22184,
Taiwan
立端科技股份有限公司
221 新北市汐止區
大同路二段 173 號7樓
T: [phone]
F: [phone]
E: [email protected]m
China
Beijing L&S Lancom Platform Tech. Co., Ltd.
Guodong LOFT 9 Layer No. 9 Huinan Road,
Huilongguan Town, Changping District, Beijing
102208 China
T: [phone]
F: [phone]
E: [e-mail]
USA
Lanner Electronics Inc.
47790 Westinghouse Drive
Fremont, CA 94539
T: [phone]
F: [phone]
E: [e-mail]
Canada
Lanner Electronics Canada Ltd
3160A Orlando Drive
Mississauga, ON
L4V 1R5 Canada
T: [phone]
F: [phone]
E: [e-mail]
Europe
Lanner Europe B.V.
Wilhelmina van Pruisenweg 104
2595 AN The Hague
The Netherlands
T: [phone]
E: [e-mail]

NCA-5230 User Manual
4
This document is copyrighted © 2022 by Lanner Electronics Inc. All rights are reserved. The original manufacturer reserves the
right to make improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior
written permission of the original manufacturer.
Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no
responsibility for its use, nor for any infringements upon the rights of third parties that may result from such use.
Intel® and Intel® Xeon® are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note
1. An unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby
radio and television reception. It is essential that only the supplied power cord be used.
2. Use only shielded cables to connect I/O devices to this equipment.
3. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Important
1. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
2. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

NCA-5230 User Manual
5
Follow these guidelines to ensure general safety:
Keep the chassis area clear and dust-free during and after installation.
Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.
Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Disconnect all power by turning off the power and unplugging the power cord before installing or removing a chassis or
working near power supplies
Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit; always check the circuit.
Suivez ces consignes pour assurer la sécuritégénérale :
Laissez la zone du châssis propre et sans poussière pendant et après l’installation.
Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre cravate ou écharpe
et remontez vos manches.
Portez des lunettes de sécurité pour protéger vos yeux.
N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement dangereux.
Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon d’alimentation avant
d’installer ou de retirer un châssis ou de travailler à proximité de sources d’alimentation.
Ne travaillez pas seul si des conditions dangereuses sont présentes.
Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil génère, utilise et
émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions des fournisseurs de
composants sans fil, il risque de provoquer des interférences dans les communications radio.
There is risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Installation should be conducted only by a trained electrician or only by an electrically trained person who knows all
installation procedures and device specifications which are to be applied.
Do not carry the handle of power supplies when moving to another place.
Please conform to your local laws and regulations regarding safe disposal of lithium batteries.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion.
Leaving a battery in an extremely high temperature environment can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.

NCA-5230 User Manual
6
Jetez les piles usagées conformément aux instructions.
L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité connaissant toutes les
spécifications d’installation et d’appareil du produit.
Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.
Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable
operating temperatures without adequate circulation. Be sure that the room in which you choose to operate your system
has adequate air circulation.
Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An open chassis permits
air leaks, which may interrupt and redirect the flow of cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic
components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-prevention
procedures when removing and replacing components to avoid these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground yourself
by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour refroidir
l’équipement à une température de fonctionnement acceptable sans circulation adaptée. Vérifiez que votre site propose
une circulation d’air adéquate.
Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de refroidissement de bien circuler.
Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et rediriger le flux d’air frais destiné aux composants
internes.
Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits électriques. Des dégâts
d’ESD surviennent lorsque des composants électroniques sont mal manipulés et peuvent causer des pannes totales ou
intermittentes. Suivez les procédures de prévention d’ESD lors du retrait et du remplacement de composants.
Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est disponible, reliez
votre corps à la terre en touchant la partie métallique du châssis.
Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et 10 mégohms
(Mohms).
Mounting Installation Precautions
The following should be put into consideration for rack-mount or similar mounting installations:
Do not install and/or operate this unit in any place that flammable objects are stored or used in.
The installation of this product must be performed by trained specialists; otherwise, a non-specialist might create the risk
of the system’s falling to the ground or other damages.
Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for supporting the system
or use of inappropriate installation components.

NCA-5230 User Manual
7
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of
the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the
equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow required for safe
operation of the equipment is not compromised.
Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved
due to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration
of equipment nameplate ratings should be used when addressing this concern.
Reliable Grounding - Reliable grounding of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
Installation & Operation
This equipment must be grounded. The power cord for product should be connected to a socket-outlet with earthing
connection.
Cet équipement doit être mis à la terre. La fiche d'alimentation doit être connectée à une prise de terre correctement
câblée
Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code
and NFPA 75.
Peut être installé dans des salles de matériel de traitement de l'information conformément à l'article 645 du National
Electrical Code et àla NFPA 75.
The machine can only be used in a restricted access location and must be installed by a skilled person.
Les matériels sont destinés àêtre installés dans des EMPLACEMENTS À ACCÈS RESTREINT.
Safety Warning
Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired earth ground
socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts.
“Product shall be used with Class 1 laser device modules.”
Avertissement
Équipement de classe I. Ce matériel doit être relié à la terre. La fiche d’alimentation doit être raccordée à une prise de terre
correctement câblée. Une prise de courant mal câblée pourrait induire des tensions dangereuses sur des parties métalliques
accessibles.
“Le produit doit être utilisé avec des modules de dispositifs laser de classe 1.”

NCA-5230 User Manual
8
Before turning on the device, ground the grounding cable of the equipment. Proper grounding (grounding) is very important
to protect the equipment against the harmful effects of external noise and to reduce the risk of electrocution in the event of
a lightning strike. To uninstall the equipment, disconnect the ground wire after turning off the power. A ground wire is
required and the part connecting the conductor must be greater than 4 mm2 or 10 AWG.
Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.
Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre les effets néfastes
du bruit externe et réduire les risques d’électrocution en cas de foudre.
Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.
Un câble de mise àla terre est requis et la zone reliant les sections du conducteur doit faire plus de 4 mm2 ou 10 AWG.
Loosen the screw of the earthing point.
Connect the grounding cable to the ground.
The protection device for the DC power source must provide 30 A current.
This protection device must be connected to the power source before DC power.
Desserrez la vis du terminal de mise àla terre.
Branchez le câble de mise àla terre àla terre.
L’appareil de protection pour la source d’alimentation CC doit fournir 30 A de
courant.
Cet appareil de protection doit être branché à la source d’alimentation avant
l’alimentation CC.

NCA-5230 User Manual
9
Main Features ....................................................................................................................................11
Package Content.................................................................................................................................11
Optional Accessories Kits ...................................................................................................................11
Ordering Information .........................................................................................................................11
System Specifications.........................................................................................................................12
Front Panel .........................................................................................................................................13
Rear Panel ..........................................................................................................................................14
Motherboard Information..................................................................................................................15
Opening the Chassis ...........................................................................................................................21
Installing the System Memory ...........................................................................................................22
Installing the IPMI Card (Optional).....................................................................................................24
Installing the TPM Module (Optional)................................................................................................25
Installing the M.2 Storage Card..........................................................................................................26
Installing the Disk Drive(s) (Optional) ................................................................................................27
Installing the NIC Modules .................................................................................................................29
Replacing the Power Supply...............................................................................................................30
Mounting the System.........................................................................................................................31
BIOS Setup..........................................................................................................................................36
Main Page...........................................................................................................................................37
Advanced Page...................................................................................................................................38
Chipset................................................................................................................................................65

NCA-5230 User Manual
10
Security...............................................................................................................................................76
Boot Menu..........................................................................................................................................79
Save and Exit Menu............................................................................................................................80
Remote Server Management.............................................................................................................82
Warranty Policy..................................................................................................................................87

NCA-5230 User Manual
11
Powered by Intel® Xeon® i9/i7/i5/i3/Pentium/Celeron CPU (Codenamed Comet Lake S), NCA-5230 supports up
to eight GbE RJ45 ports, eight SFP ports, with four bypass features. In addition to 2x NIC module slots for
expansion, 2x 2.5” HDD/SDD bays for addition storage support and up to 128GB of DDR4 system memory. NCA-
5230 is a high-performance, high-throughput network security platform designed to be optimized as the
NGFW/UTM for deployment in SMB, branch office, enterprise and cloud data centers for advanced intrusion
prevention, application/user visibility, SSL inspection and threat detection.
Intel® Xeon® i9/i7/i5/Pentium/Celeron CPU (Codenamed Comet Lake S)
8x GbE RJ45, 8x SFP, 4x Pairs of Bypass
DDR4 2933MHz ECC or Non-ECC UDIMM, max. 128GB
2x NIC Module slots, 1x RJ45 Console port, 2x USB 3.0, and 4x Keypads
350W 1+1 ATX Redundant PSUs (SKU A)
1x NCA-5230 Network Security Platform
1x Power Cable
1x Console Cable
1x SATA Cable
Nameplate
1x Short Ear Rack Mount Kit with screws
Model
Description
IAC-AST2500E
IPMI Card
Riser Card Kit
M.2 to U.2 Mini SAS NVMe Module Card and Cable (By project)
IAC-TPM04A
TPM Module Card
Slide Rail Kit
1U Slide Rackmount Rail Kit
Power Module Kit
Redundant DC Power Module Kit
SKU
Description
NCA-5230A
Intel® Comet Lake CPU, W480E CML-S PCH, 8x GbE, 8x SPF, 2x NIC Module, and
350W Redundant PSU
NCA-5230B
Intel® Comet Lake CPU, W480E CML-S PCH, 8x GbE, 8x SPF, 2x NIC Module, and
350W Single PSU

NCA-5230 User Manual
12
Form Factor
1U 19“Rackmount
Platform
Processor Options
Intel® Xeon® i9/i7/i5/i3/Pentium/Celeron CPU
(Codenamed Comet Lake S)
CPU Socket
1x LGA 1200 Socket
Chipset
CML-S W480E PCH
BIOS
AMI SPI Flash BIOS
System Memory
Technology
DDR4 ECC or Non-ECC UDIMM, up to 2933MHz
Max. Capacity
128GB
Socket
4x 288-pin DIMM
Networking
Ethernet Ports
8x GbE RJ45, with 4x bypass feature
8x SFP
NIC Module Slot
2 Slots
LOM
IO Interface
Share Ports with MGMT Ports,
No IPMI Card (Default),
Auto LOM Function with IPMI Card (Optional)
OPMA slot
Yes
I/O Interface
Reset Button
1x Reset Button (Software reset control by GPIO)
LED Indicator
Power/Status/Storage, refer to Appendix A
Power Button
1x ATX Power Switch
Console Port
1x RJ45 Console Port
USB Port
2x USB 3.0 Ports
LCD Module
4x Keypads, 16x2 Character LCD
Display
From OPMA Slot (Optional)
Power Input
AC Power Inlet on PSU
Storage
HDD/SSD Support
2x 2.5” Internal Bays
Onboard Slots
1x M.2 (SATA) 2242/2280 B+M Key
Expansion
PCIe
1x PCI-E*8 FH/HL (Optional)
mini-PCIe
N/A
SIM card Slot
N/A
Miscellaneous
Watchdog
Yes
Internal RTC with Li Battery
Yes
TPM
Yes (Optional)
Cooling
Processor
Passive CPU heat sink
System
4x cooling fans with smart fan
Environmental Parameters
Temperature
0~40ºC Operating,
-40~70ºC Non-Operating
Humidity (RH)
5~90% Operating,
5~ 95% Non-Operating
System Dimensions
Size (WxDxH)
438mm x 468mm x 44mm
Weight
7.6kg
Package Dimensions
Size (WxDxH)
739mm x 582mm x215mm
Weight
15.8 kg
Power
Type/Watts
SKU A: 350W 1+1 ATX Redundant PSUs
SKU B: 350W Single PSU
Input
AC 90V~264V @47~63Hz
Approvals and Compliance
RoHS, CE/FCC Class A, UL, UKCA

NCA-5230 User Manual
13
No.
Description
F1
LCM
16x2 character LCM
F2
Keypad
4x keypad
F3
Reset Button
1x Reset Button
F4
USB Port
2x USB 3.0 ports
F5
Console Port
1x RJ45 Console Port
F6
MGMT Port
1x RJ45 MGMT Port; Shared IPMI port (Optional)
F7
LED Indicators
F8
LAN Port
8x RJ45 Ports, 8x SFP Ports
F9
NCS2 Module
2x STD NIC Module
F6
F1
F2
F4
F5
F7
F8
F9
System Power
System Status
Storage Status
F3

NCA-5230 User Manual
14
No.
Description
R1
Cooling Fan
4x cooling fans with SMART function
R2
PCIe Expansion Slot
Optional FH/HL Size PCIe Slot for 1x PCIex8 or 2x PCIE4
R3
Redundant PSU
SKU A: 2x 350W AC Redundant PSU (N+1 design); or
SKU B: 1x 350W Single PSU
R4
Power Switch
1x Slim Type ATX Power Switch
R5
Grounding Hole
1x Semi-shearing hole for grounding screws
R6
ESD Jack
1x Semi-shearing hole for ESD screws
R1
R4
6
R3
6
R5
6
R2
6
R6
6

NCA-5230 User Manual
15
The motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a
reference for the pin assignments and the internal connectors.
The pin headers on the motherboard are often associated with essential functions. With the shunt (Jumper)
pushed down on the designated pins (the pin numbers are printed on the circuit board, surrounding the pin
header), particular features can be enabled or disabled. While changing the jumpers, make sure your system is
turned off.
Jumper Setting
To short the designated pins, push the jumper down on them so that they become SHORT. To make the pins
setting OPEN, simply remove the jumper cap.
2-pin Header
3-pin Header
4-pin Header
Open Short
Open (1-2) Jumped
Open (1-2) Jumped
1
2
1
2
3
4
1
3
2

NCA-5230 User Manual
16
1. JRST1: Reset (Default 2-3)
Controls the reset method of the Reset button on the panel
Pin No.
Description
1-2
HW Reset
2-3
SW Reset (Default)
2. JPWR1: Power –ON Button (Must be connected)
3. JUSB3: USB 3.0 Pin Header (2 Ports)
4. DP1 (not stuff): Display Port Connector
5. JATX1: 8-Pin ATX 12V Power CONN (must be connected)
6. J1: For setting JPCIESL3 / JPCIESL4 PCIe x8/x16 Setting
J1
Pin 1-2 Jumped
Pin 2-3 Jumped (Default)
JPCIESL3
x16
x8 or x4x4
JPCIESL4
x8
7. JFAN4: PWM FAN 4
8. JFAN3: PWM FAN3
9. JFAN2: PWM FAN2
10. JFAN1: PWM FAN 1
11. M.2_CN1: M.2 (SATA) 2242/2280 B-Key
12. XDP1 (not stuff): XDP Connectors
13. JDDR0: DDR4 Channel 0 DIMM0
14. JDDR1: DDR4 Channel 0 DIMM1
15. JDDR2: DDR4 Channel 1 DIMM0
16. JDDR3: DDR4 Channel 1 DIMM1
17. JCOM1: Serial Port COM2 Pin Header (Optional with JLCM1)
18. JBMC1 (only for BMC debug): BMC Debug Connector
19. U9: Super I/O NCT6776F
20. U3311: Comet Lake S CPU LGA1200 Socket
21. Power I2C: Power I2C Debug Connector
22. JPMBUUS1: ATX PMBus Pin Header
Pin No.
Description
1
TTL1
2
TTL2
3
NC
4
GND
5
NC
6
PMBUS_CLK
7
PMBUS_DATA
8
NC

NCA-5230 User Manual
17
23. JRISER1: PCH PCIe GEN3 Slot (only x4)
24. JVGA1: BMC VGA CONN1
Pin No.
Description
Pin No.
Description
1
CRT_RED
2
GND
3
CRT_GREEN
4
GND
5
CRT_BLUE
6
GND
7
HSYNC
8
NC
9
VSYNC
10
GND
11
DDC_DATA
12
DDC_CLK
25. OPMA1: IPMI AST2500 Socket
26. J80P1: 80Port Pin Header
Pin No.
Description
Pin No.
Description
1
CLK
2
LPC AD1
3
PLTRST
4
LPC AD0
5
LPC FRAME
6
3.3V
7
LPC AD3
8
--
9
LPC AD2
10
GND
27. JSPI_TPM1: BIOS Update / TPM 2.0 Pin Header
Pin No.
Description
Pin No.
Description
1
--
2
NC
3
SPI CS0
4
3.3V
5
SPI MISO
6
SPI HOLD
7
--
8
SPI CLK
9
GND
10
SPI MOSI
11
TPM IRQ
12
--
13
TPM CS
14
PLTRST
28. JLCM1: UART LCM Connector (Optional with JCOM1)
Pin No.
Description
1
TXD
2
RXD
3
GND
4
5V
29. JOPEN1: Case Open Function Pin Header
30. JCMOS1: Clear the RTC CMOS
Pin No.
Description
1-2
Normal
2-3
Clear CMOS
31. JATX2: 24 Pin ATX Power CONN (must be connected)
32. U3313: PCH W480E
33. JIO1: I/O Connector for IO-52301

NCA-5230 User Manual
18
34. JSATA PW1: SATA 5V Power Connector (only provide 5V)
35. JSATAPW2: SATA 5V Power Connector (only provide 5V)
Pin No.
Description
1
NC
2
GND
3
GND
4
5V
36. U4: I210 for MGMT (via PCIe) or IPMI LOM Port (via NCSI)
37. JSATA1: SATA3 CONN
38. JSATA2: SATA3 CONN
39. JUSB2: USB 3.0 Connector (only for IO-52301)
40. JPCIESL1: PCH PCIe GEN3 Slot, support x2x2
41. JPCIESL2: PCH PCIe GEN3 Slot, support x2x2
42. BAT1: Battery
43. JPCIESL3: CPU PCIe GEN3 Slot, support x8 (if J1 short Pin 2/3) or x16 (if J1 short Pin 1/2)
44. JPCIESL4: CPU PCIe GEN3 Slot, support x8 (if J1 short Pin 2/3) or x16 (if J1 short Pin 1/2)
J1
Pin 1-2 Jumped
Pin 2-3 Jumped (Default)
JPCIESL3
x16
x8 or x4x4
JPCIESL4
x8

NCA-5230 User Manual
19
1. JUSB3: INT USB 3.0 Pin Header (2 Ports)
2. JIO1: 3.3V / USB OVC / LED / MDI / Console / Reset Connector
Pin No.
Description
Pin No.
Description
50
+V3P3S
25
GND
49
+V3P3S
24
GND
48
+V3P3S
23
I210_MDI_0P
47
+V3P3S
22
I210_MDI_0N
46
NC
21
GND
45
NC
20
I210_MDI_1P
44
+V3P3A
19
I210_MDI_1N
43
+V3P3A
18
GND
42
+V3P3A
17
I210_MDI_2P
41
+V3P3A
16
I210_MDI_2N
40
+V3P3A
15
GND
39
+V3P3A
14
I210_MDI_3P
38
+V3P3A
13
I210_MDI_3N
37
+V3P3A
12
GND
36
+V3P3A
11
I210_LINK_100M_N
35
+V3P3A
10
I210_LINK_ACT_N
34
+V3P3A
9
I210_LINK_1G_N
33
+V3P3A
8
GND
32
NC
7
NC
31
USB_OC_0_N
6
FP_COM1_CTS_N
30
CTR_YLM_R
5
FP_COM1_RXD
29
CTR_GRN_R
4
FP_COM1_TXD
28
HD_LED_N
3
FB_RESET#
27
GND
2
FP_COM1_RTS_N
26
GND
1
GND

NCA-5230 User Manual
20
3. LAN2: INT MGMT Port Pin Header
4. JRST1: Reset Button
5. JUSB1: USB 3.0 5G
6. JUSB2: USB 3.0 5G
7. JCOM1: Console Port (Baud Rate: 115200)
8. JLOM1: MGMT/IPMI LOM Port
9. JLAN1: MGMT Port (Reserved)
10. LED1: Power / Status / HDD LED
LED1
Top
Power
Green
Middle
Status
Green/Red
Bottom
HDD
Yellow