Lantech IWMR-3003 User manual

IWMR-3003
Industrial Multifunction VPN Router w/up to 2x WiFi 11ac + up to 2
LTE 4G + 2/4 serial ports + 3 Gigabit Ethernet Switch
IMR-3003
Industrial Multifunction VPN Router w/up to 2 LTE 4G + 2/4 serial
ports + 3 Gigabit Ethernet Switch
IWAP-3003
Industrial Multifunction VPN Router w/up to 2x WiFi 11ac + 2/4
serial ports + 3 Gigabit Ethernet Switch
User Manual (Hardware)
Dec. 2021

Recommendation for Shielded network
cables
STP cables have additional shielding material that is used to reduce external
interference. The shield also reduces the emission at any point in the path of the cable.
Our recommendation is to deploy an STP network cable in demanding electrical
environments. Examples of demanding indoor environments are where the network
cable is located in parallel with electrical mains supply cables or where large inductive
loads such as motors or contactors are in close vicinity to the camera or its cable. It is
also mandatory to use an STP cable where the power device (like IP camera) is used
outdoors or where the network cable is routed outdoors.

2
Important Notice
Lantech Communications Global, Inc. reserves the right to modify the
equipment, its specification or this manual without prior notice, in the
interest of improving performance, reliability, or servicing. At the time of
publication all data is correct for the operation of the equipment at the
voltage and/or temperature referred to. Performance data indicates typical
values related to the particular product.
No part of this documentation or information supplied may be divulged to
any third party without the express written consent of Lantech
Communications Global Inc. Products offered may contain software which
is proprietary to Lantech Communications Global Inc. The offer or supply of
these products and services does not include or infer any transfer of
ownership.
Interference Issues
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a commercial or industrial installation. This equipment generates, uses,
and can radiate radio frequency energy. It may cause harmful interference
to radio communications if the equipment is not installed and used in
accordance with the instructions.

3
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy. It may cause harmful
interference to radio communications if the equipment is not installed and
used in accordance with the instructions. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Content
1. Hardware Description ............................3
1.1. Physical Dimension..................................... 3
1.2. IP Protection................................................. 8
1.3. Front Panel ................................................. 11
1.4. LED Indicators............................................ 14
2. Hardware Installation –RJ45 Models.16
2.1. Hardware installation................................. 16
2.2. DIN-Rail Mounting...................................... 16
2.3. Wall Mount Plate Mounting....................... 18
2.4. Wiring the Power Inputs............................ 20
2.4.1. Steps to Insert the Power Wire ................... 20
2.4.2. Grounding .................................................... 21
2.5. Wiring the Fault Alarm Contact ................ 22
2.6. Cabling........................................................ 23
2.7. SIM............................................................... 23
2.8. Serial Ports................................................. 25
3. Hardware Installation –M12 Models...26
3.1. Hardware installation................................. 26
3.2. Wall Mount Plate Mounting....................... 27
3.3. Wiring the Power Inputs............................ 28
3.4. Wiring the Reset or USB............................ 30
3.5. Cabling........................................................ 31
3.6. SIM............................................................... 32

4. Console Management ..........................34
4.1. Connecting to the Console Port............... 34
4.1.1. RJ45 Models................................................. 34
4.1.2. M12 models.................................................. 35
4.2. Login in the Console Interface.................. 35

3
1.Hardware Description
Lantech IWMR-3003 / IMR-3003 / IWAP-3003 are next generation industrial multi-
function VPN routers.
In this paragraph, it will describe the Industrial multi-function VPN router’s hardware
spec, port, cabling information, and wiring installation.
1.1.Physical Dimension
IWMR-3003, RJ-45 model
Metal case. IP-30,
74 (W) x 114 (D) x 152 (H) mm (12V/24V model)

4
82 (W) x 172 (D) x 152 (H) mm (WV model)
IWMR-3003, M12 model
Metal case. IP-43,
74(W) x 122(D) X 152 (H) mm

5
IMR-3003, RJ-45 model
Metal case. IP-30,
74 (W) x 114 (D) x 152 (H) mm (12V/24V model)
82 (W) x 172 (D) x 152 (H) mm (WV model)

6
IMR-3003, M12 model
Metal case. IP-43,
74(W) x 122(D) X 152 (H) mm
IWAP-3003, RJ-45 model
Metal case. IP-30,
74 (W) x 114 (D) x 152 (H) mm (12V/24V model)