lap Bronx Spike 4503R User manual

Bronx Spike Floor Light
4503R, 2491R, 9444R, 7591R
12/11/2019
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
The bulb is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
In normal circumstances, stainless steel is very resistant to corrosion. It does however require maintenance to
preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse
with clear water and with a soft cloth, wipe dry. In some cases, surface corrosion may arise after installation. This is
normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed
above. Then with a soft cloth soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash
and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
Care and cleaning: 9444R & 7591R
Care and cleaning: 4503R & 2491R
The batch date is shown on the product in the format yyWxx. The first two numbers represent the year of production
and the last two numbers after the 'W' represent the week of production within that particular year.
Batch date
This fitting has been designed to use energy efficient
LED bulbs. Ensure that the minimum distance to the
illuminated surface is not less than 0.5m (50 cm).
When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose
of used bulbs carefully. Do not exceed the wattage
stated or use a different shape bulb from that indicated
on the fitting. Use of the incorrect bulb will damage the
product and invalidate the guarantee.
Fitting/replacing bulbs: Max. 5W LED GU10
0.5m
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands.
Bronx Spike Floor Light
4503R, 2491R, 9444R, 7591R
12/11/2019
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
The bulb is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
In normal circumstances, stainless steel is very resistant to corrosion. It does however require maintenance to
preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse
with clear water and with a soft cloth, wipe dry. In some cases, surface corrosion may arise after installation. This is
normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed
above. Then with a soft cloth soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash
and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
Care and cleaning: 9444R & 7591R
Care and cleaning: 4503R & 2491R
The batch date is shown on the product in the format yyWxx. The first two numbers represent the year of production
and the last two numbers after the 'W' represent the week of production within that particular year.
Batch date
This fitting has been designed to use energy efficient
LED bulbs. Ensure that the minimum distance to the
illuminated surface is not less than 0.5m (50 cm).
When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose
of used bulbs carefully. Do not exceed the wattage
stated or use a different shape bulb from that indicated
on the fitting. Use of the incorrect bulb will damage the
product and invalidate the guarantee.
Fitting/replacing bulbs: Max. 5W LED GU10
0.5m
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands.
Bronx Spike Floor Light
4503R, 2491R, 9444R, 7591R
12/11/2019
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
The bulb is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
In normal circumstances, stainless steel is very resistant to corrosion. It does however require maintenance to
preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse
with clear water and with a soft cloth, wipe dry. In some cases, surface corrosion may arise after installation. This is
normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed
above. Then with a soft cloth soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash
and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
Care and cleaning: 9444R & 7591R
Care and cleaning: 4503R & 2491R
The batch date is shown on the product in the format yyWxx. The first two numbers represent the year of production
and the last two numbers after the 'W' represent the week of production within that particular year.
Batch date
This fitting has been designed to use energy efficient
LED bulbs. Ensure that the minimum distance to the
illuminated surface is not less than 0.5m (50 cm).
When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose
of used bulbs carefully. Do not exceed the wattage
stated or use a different shape bulb from that indicated
on the fitting. Use of the incorrect bulb will damage the
product and invalidate the guarantee.
Fitting/replacing bulbs: Max. 5W LED GU10
0.5m
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands.
Bronx Spike Floor Light
4503R, 2491R, 9444R, 7591R
12/11/2019
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
The bulb is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
In normal circumstances, stainless steel is very resistant to corrosion. It does however require maintenance to
preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse
with clear water and with a soft cloth, wipe dry. In some cases, surface corrosion may arise after installation. This is
normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed
above. Then with a soft cloth soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash
and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.
Care and cleaning: 9444R & 7591R
Care and cleaning: 4503R & 2491R
The batch date is shown on the product in the format yyWxx. The first two numbers represent the year of production
and the last two numbers after the 'W' represent the week of production within that particular year.
Batch date
This fitting has been designed to use energy efficient
LED bulbs. Ensure that the minimum distance to the
illuminated surface is not less than 0.5m (50 cm).
When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose
of used bulbs carefully. Do not exceed the wattage
stated or use a different shape bulb from that indicated
on the fitting. Use of the incorrect bulb will damage the
product and invalidate the guarantee.
Fitting/replacing bulbs: Max. 5W LED GU10
0.5m
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands.
V21220 BX220IM
Manufacturer:
UK Manufacturer:
Kingfisher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E,
1011 VM Amsterdam, The Netherlands
www.kingfisher.com/products
www.diy.com | www.screwfix.com | www.screwfix.ie
To view instruction manuals online, visit www.kingfisher.com/products
KNG2048283_ONLINE.indd 1 17/12/2020 11:01

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
This product is rated at IP44.
This product is not suitable for location in or near a marine environment.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 1 x MAX 5W LED GU10
IP rating: 44
• You have correctly identified
the wires.
• The connections are tight.
• No loose strands have been
left out of the connection
block.
If not fitting to a plug, then the product must be wired to a IP44 rated terminal block.
Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect to the
connection block inside the product in the following way:
Wiring - Terminal Block
Check that...
Layout
• Decide on the position of the luminaire. Depending on the location, an approved outdoor rated plug and socket
may be required. Alternatively an approved outdoor rated external terminal block may be used.
• Avoid locating any cables in positions that would cause a hazard. Position cables and connector block away
from areas where they may be at risk from being cut, trapped or damaged.
• Cables that are to be in walls and concealed underground must be protected using suitable conduit or plastic
trunking.
• Ensure that the ground is suitable for pushing the spike into, and can support the luminaire. Do not install in
very wet or boggy areas.
Wiring - Plug
• Theappliancemustbeconnectedtoa240voltsAC
supply.
• Theappliancecanbefittedtoarewireable3pin
plug fitted with a 3 amp fuse. Should the fuse
require replacement, it must be replaced with a fuse
rated at 3 amp and approved to BS1362.
•Thewiresinthemainsleadonthisapplianceare
coloured in accordance with the following code:
Blue – Neutral
Green / Yellow - Earth
Brown – Live
Commissioning
• Fitthebulbasperthedetailsoverleaf
• Ensurethatthegroundissuitableforpushingthespikeinto,andcansupporttheluminaire.Donotinstallinvery
wet or boggy areas. Push the spike into the ground.
• Replacefuseorcircuitbreakerandswitchon.Yourlightisnowreadyforuse.
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY LIGHT FITTING
E
L
N
GREEN/ YELLOW
Earth
Fuse
3 Amps
Cord Clamp
BLUE
Neutral
BROWN
Live
KNG2048283_ONLINE.indd 2 17/12/2020 11:01