lap 2617S-PIR User manual

6. Do not attach any other products or decorations to the lamp.
7. Do not use the luminaire in rooms and adverse surroundings where flammable
gases, vapours, or dusts exist or might exist.
8. In order to prevent fire and eye damage observe following:
- Do not look directly into the light source.
- Keep the luminaire away from flammable materials.
9. Cut the power supply completely and provide a safeguard to prevent reconnection
in case of damages of any kind, particularly in wet conditions when safe operation
is no longer ensured.
10.While using the lamp in commercial areas, additional regulations may apply.
11.Service and maintenance shall be carried out only by specialists under usage of
original replacement parts.
12.This luminaire gets hot whilst in operation. Do not install within reach of children.
Page 2 of 7
Before you start
1. Check the pack and make sure you have all of the parts listed above. If not,
contact your local LAP store who will be able to help you.
2. Decide on an appropriate location for your spotlight (see Siting Instructions below).
3. This product is not suitable for single-handed installation. An assistant will be
required during fitting.
4. If you are in any doubt about installing or assembling this product, consult a
qualified electrician.
Siting Instructions
1. This product is designed with only alternating power supply voltage connection of
220-240V / 50Hz and only use the type of bulb specified (see section "Technical
Data").
2. The Lamp is designed for outdoor use, and it is weatherproof.
3. The light is rain and splash-proof (IP44).
4. IP degree of protection is guaranteed only when properly mounted.
5. For safety reasons, using metallic components of buildings or furniture as a power
conductor is strictly forbidden.
6. Do not modify or redesign the product.
7. Different use than described above might damage the product. Moreover, it can
create hazards, such as short circuit, fire, electrical shock, etc.
8. The safety instructions and technical data must be observed strictly.
Safety Instructions
1. Installation should only be done by a qualified electrician who is familiar with the
associated risks and regulations!
2. Before connecting the device, ensure that the rated voltage and current as
indicated on the data plate match your mains supply.
3. This lamp is a Class I product and must be connected to earth.
4. Make sure that the power supply is switched off before mounting, servicing,
cleaning and maintenance.
5. During all works on the luminaire, wearing conductive jewelry like chains,
necklaces, or rings made of metal is prohibited.

Page 4 of 7
Mounting Assembly
22
7m
2.5m
120°
5cm
12cm

7fo5egaP
Setting up the Sensor
• The operation of the motion sensor is adjustable within certain parameters. For the
limits, please refer to the technical specifications.
• The switches adjustment are from left to right.
Labeling
Trimmer Variable parameters
TIME The unit will be switched off automatically on a certain time after the
last object has been detected. The duration time can be adjusted
)-(ot)+(morfbonkEMITehtgnitatoR.setunim4otsdnoces01morf
will reduce the duration time.
Note: Once the light has been triggered by the PIR sensor any
subsequent detection will start the timed period again from the
beginning.
SENSITIVITY The range of the sensor can be adjusted. The range can be adjusted
ehtnirellortnoccitamotuaehtnrutuoyfI.sretem7ottuo
clockwise direction, the range is increased, reduced with a turn
against the clockwise direction. In addition the range of the sensor
depends on the assembly height, and the sensitivity of motion sensor
will be affected by environment temperature. The more sensitivity for
PIR sensor, the lower environment temperature. So you can adjust
the SENS knob to compensate the change of sensitivity affected by
environment temperature.
LUX The Lux control module has a built-in sensing device (photocell) that
detects daylight and darkness (-☼+).(+) position denotes that the
loading will be turned on by PIR during day and night, (-) position
denotes that the loading will be turned on by PIR only at night. You
can set to operate the unit at the desired level by adjusting the LUX
knob.
Note: If in daytime when it is too light outside and if the light is not
activating during nighttime because of a street light or bright house
light, turn the control towards (+).
Pull down the cover and adjust the sensor by simply rotating in direction of arrows
using the flat screwdriver.
•

Page 6 of 7
Care and Use
• .sehsiloprosrenaelcevisarbaesutonoD.htolcpmadtfosahtiwtinuehtnaelC
Always switch the unit off and allow to cool before cleaning.
Technical Specifications
Model name: 2617S-PIR
Supply Voltage: 220-240V~, 50Hz
Bulb Type: LED 9W
Mounting Height: 2.5 meters
SYMBOL DESCRIPTION
Conformity with all relevant EC Directive requirements.
IP44 Splashproof.
Class I product, must be connected to earth.
Detection Angle: 120°
Detection Distance: up to 7 meters
Duration Time: from 10 sec to 4 mins.
Dimension L.15 x W.19.5 x H.32.5 cm
BATCH CODE EXPLANATION
yyWxx:Manufacturing date code;
year of manufacturing(yy)
and week of manufacturing(Wxx)
• LED lamp is non-replaceable light source, if the lamp is damaged ,the luminaire
must be changed.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or local store for
recycling advice.

Page 7 of 7
As of 1 January 2005, changes to the Building Regulations affected domestic electrical installations in
England and Wales.You don’t need to be a qualified electrician to make changes to your home’s
electrical system, but the work must be done in accordance with the standards in the Regulations.
You do not need to notify your Local Authority if you do minor electrical work such as:-
replacing or repairing a socket, light or cable in any room
adding extra spurs, sockets or lights to an existing circuit (except in a kitchen, bathroom or
outdoors)
adding lights to an outdoor wall on an existing circuit (provided there are no exposed outdoor
connections, and the circuit is not extended from a kitchen/bathroom).
However, the work must be done to the standards in the Wiring Regulations and you should consider
having the work checked by a competent electrician to make sure it is safe.
Before you start other electrical work such as:-
adding new circuits to your existing installation
any work (other than repairs / replacements) in a room where there is water (e.g. kitchen,
bathroom, etc.)
any work (other than repairs / replacements) outdoors (e.g. installing outdoor sockets, or non-
pre-wired garden lighting etc.)
you must notify your Local Authority Building Control Department, which has responsibility for
ensuring the work is inspected and tested.
Where you have any work done by an electrician who is a member of a competent person self-
certification scheme, the electrician will be able to certify the work complies with the Regulations and
you do not need to notify your Local Authority.
We recommend that you make yourself aware of the Regulations before you undertake any work and
if you require any clarification you should contact your Local Authority Building Control Department.
Changes to Wiring Cable Colours in UK
The IEE Wiring Regulations (BS 7671) have changed the colours in cable used for fixed wiring for all
new electrical installations.
The old and the new colours are shown in the table below.
Core colour: WENDLO
nworBdeREVIL
SWITCHED LIVE Red, or
Black with red sleeve
Brown, or
Blue with brown sleeve
eulBkcalBLARTUEN
wolley/neerghtiw,eraBHTRAE
sleeve
Bare, with green/yellow
sleeve (no change)
2-WAY SWITCHED LIVE Red, blue and yellow Brown, black and grey
For new installations after 31st March 2006, only the new colours are permitted. Where new cable is
added to an existing installation of the old type, sp ecial precautions must be taken (including fixing a
warning notice at the distribution board or consumer unit).
When installing this product, please note therefore that you may encounter either of the above types of
cable.
If you are in any doubt whatsoever regarding the above, please consult a qualified electrician.
•
•
•
•
•
•